A unit with valves for three phases, together with unit control equipment, essential protective and switching devices, DC storage capacitors, phase reactors and auxiliaries, if any, used for conversion.
A DC electrical connection point at the AC/DC converter.
A DC electrical connection point at the AC/DC converter. The AC/DC converter is electrically connected also to the AC side. The AC connection is inherited from the AC conducting equipment in the same way as any other AC equipment. The AC/DC converter DC terminal is separate from generic DC terminal to restrict the connection with the AC side to AC/DC converter and so that no other DC conducting equipment can be connected to the AC side.
Reference to the superclass object.
Represents the normal network polarity condition.
undocumented
An electrical connection point (AC or DC) to a piece of conducting equipment.
An electrical connection point (AC or DC) to a piece of conducting equipment. Terminals are connected at physical connection points called connectivity nodes.
Reference to the superclass object.
The connected status is related to a bus-branch model and the topological node to terminal relation. True implies the terminal is connected to the related topological node and false implies it is not.
The orientation of the terminal connections for a multiple terminal conducting equipment. The sequence numbering starts with 1 and additional terminals should follow in increasing order. The first terminal is the "starting point" for a two terminal branch.
The bus name marker used to name the bus (topological node).
A wire or combination of wires, with consistent electrical characteristics, building a single electrical system, used to carry alternating current between points in the power system.
A wire or combination of wires, with consistent electrical characteristics, building a single electrical system, used to carry alternating current between points in the power system. For symmetrical, transposed 3ph lines, it is sufficient to use attributes of the line segment, which describe impedances and admittances for the entire length of the segment. Additionally impedances can be computed by using length and associated per length impedances.
Reference to the superclass object.
Zero sequence shunt (charging) susceptance, uniformly distributed, of the entire line section.
Positive sequence shunt (charging) susceptance, uniformly distributed, of the entire line section. This value represents the full charging over the full length of the line.
Zero sequence shunt (charging) conductance, uniformly distributed, of the entire line section.
Positive sequence shunt (charging) conductance, uniformly distributed, of the entire line section.
Positive sequence series resistance of the entire line section.
Zero sequence series resistance of the entire line section.
Maximum permitted temperature at the end of SC for the calculation of minimum short-circuit currents. Used for short circuit data exchange according to IEC 60909
Positive sequence series reactance of the entire line section.
Zero sequence series reactance of the entire line section.
Ground action involving clamp usage (for the case when the ground is applied along the line segment instead of at its terminals).
Jumper action involving clamp usage (for the case when the jumper is applied along the line segment instead of at its terminals).
Per-length impedance of this line segment.
Represents a single wire of an alternating current line segment.
Represents a single wire of an alternating current line segment.
Reference to the superclass object.
The phase connection of the wire at both ends.
The line segment to which the phase belongs.
Models Ancillary Service Requirements.
Models Ancillary Service Requirements. Describes interval for which the requirement is applicable.
Reference to the superclass object.
The start of the time interval for which requirement is defined.
Acceptance test for assets.
Acceptance test for assets.
Reference to the superclass object.
Date and time the asset was last tested using the 'type' of test and yielding the current status in 'success' attribute.
True if asset has passed acceptance test and may be placed in or is in service. It is set to false if asset is removed from service and is required to be tested again before being placed back in service, possibly in a new location. Since asset may go through multiple tests during its lifecycle, the date of each acceptance test may be recorded in 'Asset.ActivityRecord.status.dateTime'.
Type of test or group of tests that was conducted on 'dateTime'.
A permit is sometimes needed to provide legal access to land or equipment.
A permit is sometimes needed to provide legal access to land or equipment. For example, local authority permission for road works.
Reference to the superclass object.
Permit application number that is used by municipality, state, province, etc.
Date that permit became official.
Permit expiration date.
Total cost of permit.
Permit identifier.
Credit/debit movements for an account.
Credit/debit movements for an account.
Reference to the superclass object.
Amount that was credited to/debited from an account. For example: payment received/interest charge on arrears.
Date and time when the credit/debit transaction was performed.
Reason for credit/debit transaction on an account. Example: payment received/arrears interest levied.
Unit for accounting; use either 'energyUnit' or 'currencyUnit' to specify the unit for 'value'.
Unit for accounting; use either 'energyUnit' or 'currencyUnit' to specify the unit for 'value'.
Reference to the superclass object.
Unit of service.
Unit of currency.
Multiplier for the 'energyUnit' or 'monetaryUnit'.
Value expressed in applicable units.
Accumulator represents an accumulated (counted) Measurement, e.g.
Accumulator represents an accumulated (counted) Measurement, e.g. an energy value.
Reference to the superclass object.
Normal value range maximum for any of the MeasurementValue.values. Used for scaling, e.g. in bar graphs or of telemetered raw values.
A measurement may have zero or more limit ranges defined for it.
Limit values for Accumulator measurements.
Limit values for Accumulator measurements.
Reference to the superclass object.
The value to supervise against. The value is positive.
The set of limits.
An AccumulatorLimitSet specifies a set of Limits that are associated with an Accumulator measurement.
An AccumulatorLimitSet specifies a set of Limits that are associated with an Accumulator measurement.
Reference to the superclass object.
This command reset the counter value to zero.
This command reset the counter value to zero.
Reference to the superclass object.
The accumulator value that is reset by the command.
AccumulatorValue represents an accumulated (counted) MeasurementValue.
AccumulatorValue represents an accumulated (counted) MeasurementValue.
Reference to the superclass object.
The value to supervise. The value is positive.
Measurement to which this value is connected.
The command that reset the accumulator value.
The Area Control Error tariff type that is applied or used.
The Area Control Error tariff type that is applied or used.
Reference to the superclass object.
The coded type of an ACE tariff.
undocumented
undocumented
Action request against an existing Trade.
Action request against an existing Trade.
Reference to the superclass object.
Action name type for the action request.
Limit on active power flow.
Limit on active power flow.
Reference to the superclass object.
Value of active power limit.
Records activity for an entity at a point in time; activity may be for an event that has already occurred or for a planned activity.
Records activity for an entity at a point in time; activity may be for an event that has already occurred or for a planned activity.
Reference to the superclass object.
Date and time this activity record has been created (different from the 'status.dateTime', which is the time of a status change of the associated object, if applicable).
Reason for event resulting in this activity record, typically supplied when user initiated.
Severity level of event resulting in this activity record.
Information on consequence of event resulting in this activity record.
Type of event resulting in this activity record.
Goups Adjacent Control Areas
Goups Adjacent Control Areas
Reference to the superclass object.
end effective date
Loss percentage
start effective date
undocumented
undocumented
An aggregated node can define a typed grouping further defined by the AnodeType enumeratuion.
An aggregated node can define a typed grouping further defined by the AnodeType enumeratuion. Types range from System Zone/Regions to Market Energy Regions to Aggregated Loads and Aggregated Generators.
Reference to the superclass object.
Type of aggregated node
end effective date
Processing Order for AS self-provisions for this region. The priority of this attribute directs the awards of any resource that resides in overlapping regions. The regions are processed in priority manner.
start effective date
undocumented
undocumented
undocumented
An aggregated pricing node is a specialized type of pricing node used to model items such as System Zone, Default Price Zone, Custom Price Zone, Control Area, Aggregated Generation, Aggregated Particpating Load, Aggregated Non-Participating Load, Trading Hub, Designated Control Area(DCA) Zone
An aggregated pricing node is a specialized type of pricing node used to model items such as System Zone, Default Price Zone, Custom Price Zone, Control Area, Aggregated Generation, Aggregated Particpating Load, Aggregated Non-Participating Load, Trading Hub, Designated Control Area(DCA) Zone
Reference to the superclass object.
Aggregate Price Node Types
Designated Control Area participation in LMP price measurement 'Y' - Participates in both Local Market Power Mitigation (LMPM) and System Market Power Mitigation (SMPM) 'N' - Not included in LMP price measures 'S' - Participatesin SMPM price measures 'L' - Participatesin LMPM price measures
undocumented
undocumented
Formal agreement between two parties defining the terms and conditions for a set of services.
Formal agreement between two parties defining the terms and conditions for a set of services. The specifics of the services are, in turn, defined via one or more service agreements.
Reference to the superclass object.
Date this agreement was consummated among associated persons and/or organisations.
Date and time interval this agreement is valid (from going into effect to termination).
Combustion turbine air compressor which is an integral part of a compressed air energy storage (CAES) plant.
Combustion turbine air compressor which is an integral part of a compressed air energy storage (CAES) plant.
Reference to the superclass object.
Rating of the CAES air compressor.
An air compressor may be a member of a compressed air energy storage plant.
A CAES air compressor is driven by combustion turbine.
Models Market clearing results.
Models Market clearing results. Indicates market horizon, interval based. Used by a market quality system for billing and settlement purposes
Reference to the superclass object.
undocumented
undocumented
undocumented
Models Market clearing results in terms of price and MW values
Models Market clearing results in terms of price and MW values
Reference to the superclass object.
"1" -- "Detail", "2" -- "Aggregate by Market service type", in which case, the "AllocationEnergyType" field will not be filled; "3" -- "Aggregate by "AllocationEnergyType", in which case "MarketServiceType" will not be filled.
undocumented
undocumented
undocumented
Choices are: ME - Market Energy Capacity; SR - Spinning Reserve Capacity; NR - Non-Spinning Reserve Capacity; DAC - Day Ahead Capacity; DEC - Derate Capacity
undocumented
undocumented
A prioritized measurement to be used for the generating unit in the control area specificaiton.
A prioritized measurement to be used for the generating unit in the control area specificaiton.
Reference to the superclass object.
Priority of a measurement usage. Lower numbers have first priority.
The specific analog value used as a source.
The control aread generating unit to which the prioritized measurement assignment is applied.
A prioritized measurement to be used for the tie flow as part of the control area specification.
A prioritized measurement to be used for the tie flow as part of the control area specification.
Reference to the superclass object.
Priority of a measurement usage. Lower numbers have first priority.
The specific analog value used as a source.
The tie flow of the alternate measurements.
Analog represents an analog Measurement.
Analog represents an analog Measurement.
Reference to the superclass object.
Normal value range maximum for any of the MeasurementValue.values. Used for scaling, e.g. in bar graphs or of telemetered raw values.
Normal value range minimum for any of the MeasurementValue.values. Used for scaling, e.g. in bar graphs or of telemetered raw values.
Normal measurement value, e.g., used for percentage calculations.
If true then this measurement is an active power, reactive power or current with the convention that a positive value measured at the Terminal means power is flowing into the related PowerSystemResource.
A measurement may have zero or more limit ranges defined for it.
An analog control used for supervisory control.
An analog control used for supervisory control.
Reference to the superclass object.
Normal value range maximum for any of the Control.value. Used for scaling, e.g. in bar graphs.
Normal value range minimum for any of the Control.value. Used for scaling, e.g. in bar graphs.
The MeasurementValue that is controlled.
Limit values for Analog measurements.
Limit values for Analog measurements.
Reference to the superclass object.
The value to supervise against.
The set of limits.
An AnalogLimitSet specifies a set of Limits that are associated with an Analog measurement.
An AnalogLimitSet specifies a set of Limits that are associated with an Analog measurement.
Reference to the superclass object.
Measurement quality flags for Analog Values.
Measurement quality flags for Analog Values.
Reference to the superclass object.
The quality code for the given Analog Value.
undocumented
AnalogValue represents an analog MeasurementValue.
AnalogValue represents an analog MeasurementValue.
Reference to the superclass object.
The value to supervise.
Measurement to which this value is connected.
The Control variable associated with the MeasurementValue.
Model of results of market clearing with respect to Ancillary Service products
Model of results of market clearing with respect to Ancillary Service products
Reference to the superclass object.
undocumented
Apparent power limit.
Apparent power limit.
Reference to the superclass object.
The apparent power limit.
Meeting time and location.
Meeting time and location.
Reference to the superclass object.
True if requested to call customer when someone is about to arrive at their premises.
Date and time reserved for appointment.
All works for this appointment.
AreaLoadBid is not submitted by a market participant into the Markets.
AreaLoadBid is not submitted by a market participant into the Markets. Instead, it is simply an aggregation of all LoadBids contained wtihin a specific SubControlArea. This entity should inherit from Bid for representation of the timeframe (startTime, stopTime) and the market type.
Reference to the superclass object.
The Demand Bid Megawatt for the area case. Attribute Usage: This is Scheduled demand MW in Day Ahead
Area load curve definition.
Area load curve definition.
Reference to the superclass object.
Load forecast area type.
undocumented
undocumented
undocumented
The control area's reserve specification.
The control area's reserve specification.
Reference to the superclass object.
Lower regulating margin requirement in MW, the amount of generation that can be dropped by control in 10 minutes
Operating reserve requirement in MW, where operating reserve is the generating capability that is fully available within 30 minutes. Operating reserve is composed of primary reserve (t less than 10 min) and secondary reserve (10 less than t less than 30 min).
Primary reserve requirement in MW, where primary reserve is generating capability that is fully available within 10 minutes. Primary reserve is composed of spinning reserve and quick-start reserve.
Raise regulating margin requirement in MW, the amount of generation that can be picked up by control in 10 minutes
Spinning reserve requirement in MW, spinning reserve is generating capability that is presently synchronized to the network and is fully available within 10 minutes
Description of the object or instance.
Tangible resource of the utility, including power system equipment, various end devices, cabinets, buildings, etc.
Tangible resource of the utility, including power system equipment, various end devices, cabinets, buildings, etc. For electrical network equipment, the role of the asset is defined through PowerSystemResource and its subclasses, defined mainly in the Wires model (refer to IEC61970-301 and model package IEC61970::Wires). Asset description places emphasis on the physical characteristics of the equipment fulfilling that role.
Reference to the superclass object.
Information on acceptance test.
True if asset is considered critical for some reason (for example, a pole with critical attachments).
Electronic address.
Condition of asset in inventory or at time of installation. Examples include new, rebuilt, overhaul required, other. Refer to inspection data for information on the most current condition of the asset.
Whenever an asset is reconditioned, percentage of expected life for the asset when it was new; zero for new devices.
Lifecycle dates for this asset.
Lot number for this asset. Even for the same model and version number, many assets are manufactured in lots.
Purchase price of asset.
Serial number of this asset.
Status of this asset.
Utility-specific classification of Asset and its subtypes, according to their corporate standards, practices, and existing IT systems (e.g., for management of assets, maintenance, work, outage, customers, etc.).
Uniquely tracked commodity (UTC) number.
All activity records created for this asset.
Container of this asset.
Data applicable to this asset.
undocumented
undocumented
undocumented
undocumented
undocumented
Location of this asset.
All roles an organisation plays for this asset.
All power system resources used to electrically model this asset. For example, transformer asset is electrically modelled with a transformer and its windings and tap changer.
Asset that is aggregation of other assets such as conductors, transformers, switchgear, land, fences, buildings, equipment, vehicles, etc.
Asset that is aggregation of other assets such as conductors, transformers, switchgear, land, fences, buildings, equipment, vehicles, etc.
Reference to the superclass object.
Function performed by an asset.
Function performed by an asset.
Reference to the superclass object.
Configuration specified for this function.
Firmware version.
Hardware version.
Password needed to access this function.
Name of program.
Set of attributes of an asset, representing typical datasheet information of a physical device that can be instantiated and shared in different data exchange contexts: - as attributes of an asset instance (installed or in stock) - as attributes of an asset model (product by a manufacturer) - as attributes of a type asset (generic type of an asset as used in designs/extension planning).
Set of attributes of an asset, representing typical datasheet information of a physical device that can be instantiated and shared in different data exchange contexts: - as attributes of an asset instance (installed or in stock) - as attributes of an asset model (product by a manufacturer) - as attributes of a type asset (generic type of an asset as used in designs/extension planning).
Reference to the superclass object.
Asset model described by this data.
Potential hazard related to the location of an asset.
Potential hazard related to the location of an asset. Examples are trees growing under overhead power lines, a park being located by a substation (i.e., children climb fence to recover a ball), a lake near an overhead distribution line (fishing pole/line contacting power lines), dangerous neighbour, etc.
Reference to the superclass object.
The location of this hazard.
Model of an asset, either a product of a specific manufacturer or a generic asset model or material item.
Model of an asset, either a product of a specific manufacturer or a generic asset model or material item. Datasheet characteristics are available through the associated AssetInfo subclass and can be shared with asset or power system resource instances.
Reference to the superclass object.
Data applicable to this asset model.
Catalogue of available types of products and materials that are used to build or install, maintain or operate an Asset.
Catalogue of available types of products and materials that are used to build or install, maintain or operate an Asset. Each catalogue item is for a specific product (AssetModel) available from a specific supplier.
Reference to the superclass object.
undocumented
Provides pricing and other relevant information about a specific manufacturer's product (i.e., AssetModel), and its price from a given supplier.
Provides pricing and other relevant information about a specific manufacturer's product (i.e., AssetModel), and its price from a given supplier. A single AssetModel may be availble from multiple suppliers. Note that manufacturer and supplier are both types of organisation, which the association is inherited from Document.
Reference to the superclass object.
Unit cost for an asset model from a specific supplier, either for a unit cost or cost per unit length. Cost is for material or asset only and does not include labor to install/construct or configure it.
undocumented
undocumented
Role an organisation plays with respect to asset.
Role an organisation plays with respect to asset.
Reference to the superclass object.
Owner of the asset.
Owner of the asset.
Reference to the superclass object.
An Asset Property that is described through curves rather than as a data point.
An Asset Property that is described through curves rather than as a data point. The relationship is to be defined between an independent variable (X-axis) and one or two dependent variables (Y1-axis and Y2-axis).
Reference to the superclass object.
undocumented
Organisation that is a user of the asset.
Organisation that is a user of the asset.
Reference to the superclass object.
An assignment is given to an ErpPerson, Crew, Organisation, Equipment Item, Tool, etc.
An assignment is given to an ErpPerson, Crew, Organisation, Equipment Item, Tool, etc. and may be used to perform Work, WorkTasks, Procedures, etc. TimeSchedules may be set up directly for Assignments or indirectly via the associated WorkTask. Note that these associations are all inherited through the recursive relationship on Document.
Reference to the superclass object.
Period between the assignment becoming effective and its expiration.
A rotating machine whose shaft rotates asynchronously with the electrical field.
A rotating machine whose shaft rotates asynchronously with the electrical field. Also known as an induction machine with no external connection to the rotor windings, e.g squirrel-cage induction machine.
Reference to the superclass object.
Indicates the type of Asynchronous Machine (motor or generator).
Indicates whether the machine is a converter fed drive. Used for short circuit data exchange according to IEC 60909
Efficiency of the asynchronous machine at nominal operation in percent. Indicator for converter drive motors. Used for short circuit data exchange according to IEC 60909
Ratio of locked-rotor current to the rated current of the motor (Ia/Ir). Used for short circuit data exchange according to IEC 60909
Nameplate data indicates if the machine is 50 or 60 Hz.
Nameplate data. Depends on the slip and number of pole pairs.
Number of pole pairs of stator. Used for short circuit data exchange according to IEC 60909
Rated mechanical power (Pr in the IEC 60909-0). Used for short circuit data exchange according to IEC 60909.
Indicates for converter drive motors if the power can be reversible. Used for short circuit data exchange according to IEC 60909
Damper 1 winding resistance.
Damper 2 winding resistance.
Locked rotor ratio (R/X). Used for short circuit data exchange according to IEC 60909
Transient rotor time constant (greater than tppo).
Sub-transient rotor time constant (greater than 0).
Damper 1 winding leakage reactance.
Damper 2 winding leakage reactance.
Magnetizing reactance.
Transient reactance (unsaturated) (greater than or equal to xpp).
Sub-transient reactance (unsaturated) (greather than Xl).
Synchronous reactance (greather than xp).
Asynchronous machine dynamics model used to describe dynamic behavior of this asynchronous machine.
Asynchronous machine whose behaviour is described by reference to a standard model expressed in either time constant reactance form or equivalent circuit form <font color="#0f0f0f">or by definition of a user-defined model.</font>
Asynchronous machine whose behaviour is described by reference to a standard model expressed in either time constant reactance form or equivalent circuit form <font color="#0f0f0f">or by definition of a user-defined model.</font>
Parameter Notes:
Reference to the superclass object.
Asynchronous machine to which this asynchronous machine dynamics model applies.
Mechanical load model associated with this asynchronous machine model.
Turbine-governor model associated with this asynchronous machine model.
Wind generator type 1 or 2 model associated with this asynchronous machine model.
The electrical equations of all variations of the asynchronous model are based on the AsynchronousEquivalentCircuit diagram for the direct and quadrature axes, with two equivalent rotor windings in each axis.
The electrical equations of all variations of the asynchronous model are based on the AsynchronousEquivalentCircuit diagram for the direct and quadrature axes, with two equivalent rotor windings in each axis.
Equations for conversion between Equivalent Circuit and Time Constant Reactance forms: Xs = Xm + Xl X' = Xl + Xm * Xlr1 / (Xm + Xlr1) X'' = Xl + Xm * Xlr1* Xlr2 / (Xm * Xlr1 + Xm * Xlr2 + Xlr1 * Xlr2) T'o = (Xm + Xlr1) / (omega0 * Rr1) T''o = (Xm * Xlr1 + Xm * Xlr2 + Xlr1 * Xlr2) / (omega0 * Rr2 * (Xm + Xlr1) Same equations using CIM attributes from AsynchronousMachineTimeConstantReactance class on left of = sign and AsynchronousMachineEquivalentCircuit class on right (except as noted): xs = xm + RotatingMachineDynamics.statorLeakageReactance xp = RotatingMachineDynamics.statorLeakageReactance + xm * xlr1 / (xm + xlr1) xpp = RotatingMachineDynamics.statorLeakageReactance + xm * xlr1* xlr2 / (xm * xlr1 + xm * xlr2 + xlr1 * xlr2) tpo = (xm + xlr1) / (2*pi*nominal frequency * rr1) tppo = (xm * xlr1 + xm * xlr2 + xlr1 * xlr2) / (2*pi*nominal frequency * rr2 * (xm + xlr1).
Reference to the superclass object.
Damper 1 winding resistance.
Damper 2 winding resistance.
Damper 1 winding leakage reactance.
Damper 2 winding leakage reactance.
Magnetizing reactance.
Parameter Notes:
Parameter Notes:
The parameters used for models expressed in time constant reactance form include:
Reference to the superclass object.
Transient rotor time constant (T'o) (> To). Typical Value = 5.
Subtransient rotor time constant (To) (> 0). Typical Value = 0.03.
Transient reactance (unsaturated) (X') (>=X). Typical Value = 0.5.
Subtransient reactance (unsaturated) (X) (> Xl). Typical Value = 0.2.
Synchronous reactance (Xs) (>= X'). Typical Value = 1.8.
Asynchronous machine whose dynamic behaviour is described by a user-defined model.
Asynchronous machine whose dynamic behaviour is described by a user-defined model.
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
A class used to provide information about an attribute.
A class used to provide information about an attribute.
Reference to the superclass object.
The identification of the formal name of an attribute.
The instance value of the attribute.
A sequential value representing a relative sequence number.
undocumented
Property for a particular attribute that contains name and value
Property for a particular attribute that contains name and value
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
A class providing the identification and type of an auction.
A class providing the identification and type of an auction.
Reference to the superclass object.
Identification of the method of allocation in an auction.
An indicator that signifies that the auction has been cancelled.
The product category of an auction.
The terms which dictate the determination of the bid payment price.
The rights of use the transmission capacity acquired in an auction.
The kind of the Auction (e.g. implicit, explicit ...).
undocumented
Variable and dynamic part of auxiliary agreement, generally representing the current state of the account related to the outstanding balance defined in auxiliary agreement.
Variable and dynamic part of auxiliary agreement, generally representing the current state of the account related to the outstanding balance defined in auxiliary agreement.
Reference to the superclass object.
The total amount currently remaining on this account that is required to be paid in order to settle the account to zero. This excludes any due amounts not yet paid.
Current amounts now due for payment on this account.
Details of the last credit transaction performed on this account.
Details of the last debit transaction performed on this account.
The initial principle amount, with which this account was instantiated.
Auxiliary agreement regulating this account.
All charges levied on this account.
An ad-hoc auxiliary account agreement associated with a customer agreement, not part of the customer's account, but typically subject to formal agreement between customer and supplier (utility).
An ad-hoc auxiliary account agreement associated with a customer agreement, not part of the customer's account, but typically subject to formal agreement between customer and supplier (utility). Typically this is used to collect revenue owed by the customer for other services or arrears accrued with the utility for other services. It is typically linked to a prepaid token purchase transaction, thus forcing the customer to make a payment towards settlement of the auxiliary account balance whenever the customer needs to purchase a prepaid token for electricity.
Reference to the superclass object.
The interest per annum to be charged prorata on 'AuxiliaryAccount.dueArrears' at the end of each 'payCycle'.
The frequency for automatically recurring auxiliary charges, where 'AuxiliaryAccount.initialCharge' is recursively added to 'AuxiliaryAccount.dueCurrent' at the start of each 'auxCycle'. For example: on a specified date and time; hourly; daily; weekly; monthly; 3-monthly; 6-monthly; 12-monthly; etc.
The coded priority indicating the priority that this auxiliary agreement has above other auxiliary agreements (associated with the same customer agreement) when it comes to competing for settlement from a payment transaction or token purchase.
The fixed amount that has to be collected from each vending transaction towards settlement of this auxiliary agreement. Note that there may be multiple tokens vended per vending transaction, but this is not relevant.
The minimum amount that has to be paid at any transaction towards settling this auxiliary agreement or reducing the balance.
The contractually expected payment frequency (by the customer). Examples are: ad-hoc; on specified date; hourly, daily, weekly, monthly. etc.
Sub-classification of the inherited 'type' for this AuxiliaryAgreement.
The percentage of the transaction amount that has to be collected from each vending transaction towards settlement of this auxiliary agreement when payments are not in arrears. Note that there may be multiple tokens vended per vending transaction, but this is not relevant.
The percentage of the transaction amount that has to be collected from each vending transaction towards settlement of this auxiliary agreement when payments are in arrears. Note that there may be multiple tokens vended per vending transaction, but this is not relevant.
Customer agreement this (non-service related) auxiliary agreement refers to.
Models Market clearing results for Auxillary costs
Models Market clearing results for Auxillary costs
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
AuxiliaryEquipment describe equipment that is not performing any primary functions but support for the equipment performing the primary function.
AuxiliaryEquipment describe equipment that is not performing any primary functions but support for the equipment performing the primary function. AuxiliaryEquipment is attached to primary eqipment via an association with Terminal.
Reference to the superclass object.
The Terminal at the equipment where the AuxiliaryEquipment is attached.
Models Auxillary Values
Models Auxillary Values
Reference to the superclass object.
undocumented
undocumented
Models Auxillary Values
Models Auxillary Values
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
Boiling water reactor used as a steam supply to a steam turbine.
Boiling water reactor used as a steam supply to a steam turbine.
Reference to the superclass object.
High power limit.
In-core thermal time constant.
Integral gain.
Low power limit.
Initial lower limit.
Pressure limit.
Pressure setpoint gain adjuster.
Pressure setpoint time constant.
Pressure setpoint time constant.
Proportional gain.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Coefficient for modeling the effect of off-nominal frequency and voltage on recirculation and core flow, which affects the BWR power output.
Rod pattern.
Constant associated with rod pattern.
Initial upper limit.
Organisation that is a commercial bank, agency, or other institution that offers a similar service.
Organisation that is a commercial bank, agency, or other institution that offers a similar service.
Reference to the superclass object.
Bank identifier code as defined in ISO 9362; for use in countries wher IBAN is not yet in operation.
International bank account number defined in ISO 13616; for countries where IBAN is not in operation, the existing BIC or SWIFT codes may be used instead (see ISO 9362).
Bank account.
Bank account.
Reference to the superclass object.
Account reference number.
Bank that provides this BankAccount.
ServiceSupplier that is owner of this BankAccount.
Details of a bank account.
Details of a bank account.
Reference to the superclass object.
Operational account reference number.
Name of bank where account is held.
Branch of bank where account is held.
National identity number (or equivalent) of account holder.
Name of account holder.
Possibly time-varying max MW or MVA and optionally Min MW limit or MVA limit (Y1 and Y2, respectively) assigned to a contingency analysis base case.
Possibly time-varying max MW or MVA and optionally Min MW limit or MVA limit (Y1 and Y2, respectively) assigned to a contingency analysis base case. Use CurveSchedule XAxisUnits to specify MW or MVA. To be used only if the BaseCaseConstraintLimit differs from the DefaultConstraintLimit.
Reference to the superclass object.
undocumented
The class describe a base frequency for a power system network.
The class describe a base frequency for a power system network. In case of multiple power networks with different frequencies, e.g. 50 or 60 Hertz each network will have it's own base frequency class. Hence it is assumed that power system objects having different base frequencies appear in separate documents where each document has a single base frequency instance.
Reference to the superclass object.
The base frequency.
The BasePower class defines the base power used in the per unit calculations.
The BasePower class defines the base power used in the per unit calculations.
Reference to the superclass object.
Value used as base power.
Common representation for reading values.
Common representation for reading values. Note that a reading value may have multiple qualities, as produced by various systems ('ReadingQuality.source').
Reference to the superclass object.
(used only when there are detailed auditing requirements) Date and time at which the reading was first delivered to the metering system.
System that originally supplied the reading (e.g., customer, AMI system, handheld reading system, another enterprise system, etc.).
Start and end of the period for those readings whose type has a time attribute such as 'billing', seasonal' or 'forTheSpecifiedPeriod'.
Value of this reading.
Defines a system base voltage which is referenced.
Defines a system base voltage which is referenced.
Reference to the superclass object.
The power system resource's base voltage.
Common representation for work and work tasks.
Common representation for work and work tasks.
Reference to the superclass object.
Kind of work.
Priority of work.
Kind of work status.
Location for this work/task.
Top level element.
Top level element.
Not all elements really have an mRID (classes in package Common like PositionPoint and PostalAddress) But Spark needs identifiers for joins, so, for now all elements have an mRID.
Reference to the superclass object.
Master resource identifier issued by a model authority. By convention, this is used as the RDF id in the CIM XML.
Schedule of values at points in time.
Schedule of values at points in time.
Reference to the superclass object.
The time for the first time point.
Multiplier for value1.
Value1 units of measure.
Multiplier for value2.
Value2 units of measure.
A collection of power system resources (within a given substation) including conducting equipment, protection relays, measurements, and telemetry.
A collection of power system resources (within a given substation) including conducting equipment, protection relays, measurements, and telemetry. A bay typically represents a physical grouping related to modularization of equipment.
Reference to the superclass object.
Indicates the presence/absence of energy measurements.
Indicates the presence/absence of active/reactive power measurements.
Breaker configuration.
Bus bar configuration.
Substation containing the bay.
The voltage level containing this bay.
Represents both bids to purchase and offers to sell energy or ancillary services in an RTO-sponsored market.
Represents both bids to purchase and offers to sell energy or ancillary services in an RTO-sponsored market.
Reference to the superclass object.
The market type, DAM or RTM.
Start time and date for which bid applies.
Stop time and date for which bid is applicable.
undocumented
undocumented
undocumented
undocumented
This class allows SC to input different time intervals for distribution factors
This class allows SC to input different time intervals for distribution factors
Reference to the superclass object.
End of the time interval n which bid is valid (yyyy-mm-dd hh24: mi: ss)
Start of the time interval in which bid is valid (yyyy-mm-dd hh24: mi: ss).
undocumented
This class represent the error information for a bid that is detected during bid validation
This class represent the error information for a bid that is detected during bid validation
Reference to the superclass object.
undocumented
hour wihthin the bid for which the error applies
error message
Priority number for the error message
undocumented
undocumented
undocumented
hour wihthin the bid for which the error applies
undocumented
Containment for bid parameters that are dependent on a market product type.
Containment for bid parameters that are dependent on a market product type.
Reference to the superclass object.
undocumented
Containment for bid hourly parameters that are not product dependent.
Containment for bid hourly parameters that are not product dependent.
Reference to the superclass object.
undocumented
This class represent the bid price cap.
This class represent the bid price cap.
Reference to the superclass object.
Bid Ceiling ($/MWH)
Bid Ceiling ($/MWH) for generic AS versus a specific market product
Bid Floor, ($/MWH)
Bid Floor ($/MWH) for generic AS versus a specific market product
Bid Default Price($/MWH)
Market Type of the cap (DAM or RTM)
undocumented
Relationship between unit operating price in $/hour (Y-axis) and unit output in MW (X-axis).
Relationship between unit operating price in $/hour (Y-axis) and unit output in MW (X-axis).
Reference to the superclass object.
Defines bid schedules to allow a product bid to use specified bid price curves for different time intervals.
Defines bid schedules to allow a product bid to use specified bid price curves for different time intervals.
Reference to the superclass object.
BID Type: I - Initial Bid; F - Final Bid
Mitigation Status: 'S' - Mitigated by SMPM because of "misconduct" 'L; - Mitigated by LMPM because of "misconduct" 'R' - Modified by LMPM because of RMR rules 'M' - Mitigated because of "misconduct" both by SMPM and LMPM 'B' - Mitigated because of "misconduct" both by SMPM and modified by LMLM because of RMR rules 'O' - original
undocumented
undocumented
Defines self schedule values to be used for specified time intervals.
Defines self schedule values to be used for specified time intervals.
Reference to the superclass object.
This is a Y/N flag for a self-schedule of a resource per market per date and hour, using a specific TR ID. It indicates whether a self-schedule using a TR is balanced with another self-schedule using the same TR ID.
bidType has two types as the required output of requirements and qualified pre-dispatch.
This is a Y/N flag for a self-schedule of a resource per market per date and hour, using a specific TR ID. It indicates whether a self-schedule using a TR has scheduling priority in DAM/RTM.
Contains the PriceTaker, ExistingTransmissionContract, TransmissionOwnershipRights pumping self schedule quantity. If this value is not null, then the unit is in pumping mode.
Indication of which type of self schedule is being referenced.
Self scheduled value
Price Taker Export Self Sched Support Resource
This attribute is used to specify if a bid includes a self sched bid. If so what self sched type is it. The possible values are shown as follow but not limited to:
undocumented
A unique identifier of a wheeling transaction. A wheeling transaction is a balanced Energy exchange among Supply and Demand Resources.
undocumented
undocumented
undocumented
undocumented
undocumented
As set of mutually exclusive bids for which a maximum of one may be scheduled.
As set of mutually exclusive bids for which a maximum of one may be scheduled. Of these generating bids, only one generating bid can be scheduled at a time.
Reference to the superclass object.
The formal specification of specific characteristics related to a bid.
The formal specification of specific characteristics related to a bid.
Reference to the superclass object.
Indication that the values in the period are considered as a whole. They cannot be changed or subdivided.
The coded identification of the energy flow.
An indication whether or not each element of the bid may be partially accepted or not.
Unique identification associated with all linked bids.
The minimum quantity of energy that can be activated at a given time interval.
The minimum increment that can be applied for an increase in an activation request.
Bilateral transaction
Bilateral transaction
Reference to the superclass object.
Maximum curtailment time in number of trading intervals
Minimum curtailment time in number of trading intervals
Market type (default=DA) DA - Day Ahead RT - Real Time HA - Hour Ahead
Maximum purchase time in number of trading intervals
Minimum purchase time in number of trading intervals
Transaction scope: 'Internal' (default) 'External'
Maximum total transmission (congestion) charges in monetary units
Transaction type (default 1) 1 - Fixed 2 - Dispatchable continuous 3 - Dispatchable block-loading
Model various charges to support billing and settlement of
Model various charges to support billing and settlement of
Reference to the superclass object.
Level in charge calculation order.
The version of configuration of calculation logic in the settlement.
undocumented
undocumented
undocumented
undocumented
undocumented
Number of intervals of bill determiant in trade day, eg 300 for five minute intervals.
undocumented
The level of precision in the current value.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
The UOM for the current value of the Bill Determinant.
undocumented
undocumented
Dynamic flows and ratings associated with a branch end.
Dynamic flows and ratings associated with a branch end.
Reference to the superclass object.
The Load Dump Rating for the branch
The Long Term Rating for the branch
The MVAR flow on the branch Attribute Usage: Reactive power flow at the series device, transformer, phase shifter, or line end
The MW flow on the branch Attribute Usage: Active power flow at the series device, transformer, phase shifter, or line end
The Normal Rating for the branch
The Short Term Rating for the branch
A group of branch terminals whose directed flow summation is to be monitored.
A group of branch terminals whose directed flow summation is to be monitored. A branch group need not form a cutset of the network.
Reference to the superclass object.
The maximum active power flow.
The maximum reactive power flow.
The minimum active power flow.
The minimum reactive power flow.
Monitor the active power flow.
Monitor the reactive power flow.
A specific directed terminal flow for a branch group.
A specific directed terminal flow for a branch group.
Reference to the superclass object.
The flow into the terminal is summed if set true. The flow out of the terminanl is summed if set false.
The branch group to which the directed branch group terminals belong.
The terminal to be summed.
A mechanical switching device capable of making, carrying, and breaking currents under normal circuit conditions and also making, carrying for a specified time, and breaking currents under specified abnormal circuit conditions e.g.
A mechanical switching device capable of making, carrying, and breaking currents under normal circuit conditions and also making, carrying for a specified time, and breaking currents under specified abnormal circuit conditions e.g. those of short circuit.
Reference to the superclass object.
The transition time from open to close.
Properties of breaker assets.
Properties of breaker assets.
Reference to the superclass object.
Phase trip rating.
Used to apply user standard names to topology buses.
Used to apply user standard names to topology buses. Typically used for "bus/branch" case generation. Associated with one or more terminals that are normally connected with the bus name. The associated terminals are normally connected by non-retained switches. For a ring bus station configuration, all busbar terminals in the ring are typically associated. For a breaker and a half scheme, both busbars would normally be associated. For a ring bus, all busbars would normally be associated. For a "straight" busbar configuration, normally only the main terminal at the busbar would be associated.
Reference to the superclass object.
Priority of bus name marker for use as topology bus name. Use 0 for don t care. Use 1 for highest priority. Use 2 as priority is less than 1 and so on.
The reporting group to which this bus name marker belongs.
A conductor, or group of conductors, with negligible impedance, that serve to connect other conducting equipment within a single substation.
A conductor, or group of conductors, with negligible impedance, that serve to connect other conducting equipment within a single substation. Voltage measurements are typically obtained from VoltageTransformers that are connected to busbar sections. A bus bar section may have many physical terminals but for analysis is modelled with exactly one logical terminal.
Reference to the superclass object.
Maximum allowable peak short-circuit current of busbar (Ipmax in the IEC 60909-0). Mechanical limit of the busbar in the substation itself. Used for short circuit data exchange according to IEC 60909
A VoltageControlZone is controlled by a designated BusbarSection.
Busbar section data.
Busbar section data.
Reference to the superclass object.
Rated current.
Rated voltage.
Bushing asset.
Bushing asset.
Reference to the superclass object.
Factory measured capacitance, measured between the power factor tap and the bushing conductor.
Factory measured insulation power factor, measured between the power factor tap and the bushing conductor.
Factory measured capacitance measured between the power factor tap and ground.
Factory measured insulation power factor, measured between the power factor tap and ground.
Kind of insulation.
undocumented
Bushing insulation power factor condition as a result of a test.
Bushing insulation power factor condition as a result of a test. Typical status values are: Acceptable, Minor Deterioration or Moisture Absorption, Major Deterioration or Moisture Absorption, Failed.
Reference to the superclass object.
undocumented
Kind of test for this bushing.
undocumented
undocumented
Business justification for capital expenditures, usually addressing operations and maintenance costs as well.
Business justification for capital expenditures, usually addressing operations and maintenance costs as well.
Reference to the superclass object.
A codified representation of the business case (i.e., codes for highway relocation, replace substation transformers, etc.).
A BusinessPlan is an organized sequence of predetermined actions required to complete a future organizational objective.
A BusinessPlan is an organized sequence of predetermined actions required to complete a future organizational objective. It is a type of document that typically references a schedule, physical and/or logical resources (assets and/or PowerSystemResources), locations, etc.
Reference to the superclass object.
A business role that this organisation plays.
A business role that this organisation plays. A single organisation typically performs many functions, each one described as a role.
Reference to the superclass object.
undocumented
Classification by utility's corporate standards and practices.
Compressed air energy storage plant.
Compressed air energy storage plant.
Reference to the superclass object.
The rated energy storage capacity.
The CAES plant's gross rated generating capacity.
An air compressor may be a member of a compressed air energy storage plant.
A thermal generating unit may be a member of a compressed air energy storage plant.
Congestion Revenue Rights (CRR) class that is inherited from a Document class.
Congestion Revenue Rights (CRR) class that is inherited from a Document class. A CRR is a financial concept that is used to hedge congestion charges.
Reference to the superclass object.
CRR category represents 'PTP' for a point-to-point CRR, or 'NSR' for a Network Service Right . If CRR category is 'PTP', both Source ID and Sink ID fields are required. If CRR category is 'NSR' only one field, either Source ID or Sink ID, shall be not null and the other shall be null. However, the 'NSR' category will include at least three records
Type of the CRR, from the possible type definitions in the CRR System (e.g. 'LSE', 'ETC').
hedger type Obligation or Option
Time of Use flag of the CRR - Peak (ON), Offpeak (OFF) or all 24 hours (24HR).
Segment of the CRR described in the current record
undocumented
undocumented
Model that describes the Congestion Revenue Rights Auction Market
Model that describes the Congestion Revenue Rights Auction Market
Reference to the superclass object.
labelID - an ID for a set of apnodes/pnodes used in a CRR market
Identifies a way in which an organisation may participate with a defined Congestion Revenue Right (CRR).
Identifies a way in which an organisation may participate with a defined Congestion Revenue Right (CRR).
Reference to the superclass object.
Kind of role the organisation is with regards to the congestion revenue rights.
Status of congestion revenue rights organisation role.
undocumented
undocumented
CRRSegment represents a segment of a CRR in a particular time frame.
CRRSegment represents a segment of a CRR in a particular time frame. The segment class contains CRR kind, type, quantity, hedger type, time of use flag, and segment period.
Reference to the superclass object.
Dollar amount = quantity x clearingPrice
Clearing price of a CRR
segment end date time
The MW amount associated with the CRR
segment start date time
undocumented
Relationship between the combustion turbine's power output rating in gross active power (X-axis) and the ambient air temperature (Y-axis).
Relationship between the combustion turbine's power output rating in gross active power (X-axis) and the ambient air temperature (Y-axis).
Reference to the superclass object.
A combustion turbine may have an active power versus ambient temperature relationship.
Allowed actions: Install, Remove, Transfer, Abandon, etc.
Allowed actions: Install, Remove, Transfer, Abandon, etc.
Reference to the superclass object.
undocumented
Compatible unit for various types of assets such as transformers switches, substation fences, poles, etc..
Compatible unit for various types of assets such as transformers switches, substation fences, poles, etc..
Reference to the superclass object.
Quantity of the type asset within the CU.
undocumented
The code for this type of asset.
undocumented
Compatible unit contractor item.
Compatible unit contractor item.
Reference to the superclass object.
Activity code identifies a specific and distinguishable unit of work.
The amount that a given contractor will charge for performing this unit of work.
undocumented
undocumented
A Compatible Unit Group identifies a set of compatible units which may be jointly utilized for estimating and designating jobs.
A Compatible Unit Group identifies a set of compatible units which may be jointly utilized for estimating and designating jobs.
Reference to the superclass object.
undocumented
undocumented
Labor code associated with various compatible unit labor items.
Labor code associated with various compatible unit labor items.
Reference to the superclass object.
Labor code.
undocumented
Compatible unit labor item.
Compatible unit labor item.
Reference to the superclass object.
Activity code identifies a specific and distinguishable unit of work.
Estimated time to perform work.
The labor rate applied for work.
undocumented
undocumented
undocumented
undocumented
Compatible unit of a consumable supply item.
Compatible unit of a consumable supply item. For example, nuts, bolts, brackets, glue, etc.
Reference to the superclass object.
Code for material.
Quantity of the TypeMaterial for this CU, used to determine estimated costs based on a per unit cost or a cost per unit length specified in the TypeMaterial.
undocumented
undocumented
undocumented
Compatible unit for various types of WorkEquipmentAssets, including vehicles.
Compatible unit for various types of WorkEquipmentAssets, including vehicles.
Reference to the superclass object.
The equipment type code.
Standard usage rate for the type of vehicle.
undocumented
undocumented
undocumented
Enclosure that offers protection to the equipment it contains and/or safety to people/animals outside it.
Enclosure that offers protection to the equipment it contains and/or safety to people/animals outside it.
Reference to the superclass object.
Cable data.
Cable data.
Reference to the superclass object.
Kind of construction of this cable.
Diameter over the core, including any semi-con screen; should be the insulating layer's inside diameter.
Diameter over the insulating layer, excluding outer screen.
Diameter over the outermost jacketing layer.
Diameter over the outer screen; should be the shield's inside diameter.
True if wire strands are extruded in a way to fill the voids in the cable.
Maximum nominal design operating temperature.
Kind of outer jacket of this cable.
True if sheath / shield is used as a neutral (i.e., bonded).
Material of the shield.
Capabilities of a crew.
Capabilities of a crew.
Reference to the superclass object.
Capability performance factor.
undocumented
Classification by utility's work management standards and practices.
Date and time interval for which this capability is valid (when it became effective and when it expires).
undocumented
undocumented
undocumented
Documentation of the tender when it is a type of card (credit, debit, etc).
Documentation of the tender when it is a type of card (credit, debit, etc).
Reference to the superclass object.
Name of account holder.
The card verification number.
The date when this card expires.
The primary account number.
Payment tender this card is being used for.
The operator of the point of sale for the duration of CashierShift.
The operator of the point of sale for the duration of CashierShift. Cashier is under the exclusive management control of Vendor.
Reference to the superclass object.
Electronic address.
The operating shift for a cashier, during which the cashier may transact against the cashier shift, subject to vendor shift being open.
The operating shift for a cashier, during which the cashier may transact against the cashier shift, subject to vendor shift being open.
Reference to the superclass object.
The amount of cash that the cashier brings to start the shift and that will be taken away at the end of the shift; i.e. the cash float does not get banked.
Cashier operating this shift.
Point of sale that is in operation during this shift.
A single path for the collection or reporting of register values over a period of time.
A single path for the collection or reporting of register values over a period of time. For example, a register which measures forward energy can have two channels, one providing bulk quantity readings and the other providing interval readings of a fixed interval size.
Reference to the superclass object.
If true, the data is being calculated by an enterprise system rather than metered directly.
Reading type for register values reported/collected by this channel.
Register whose values are collected/reported by this channel.
A charge element associated with other entities such as tariff structures, auxiliary agreements or other charge elements.
A charge element associated with other entities such as tariff structures, auxiliary agreements or other charge elements. The total charge amount applicable to this instance of charge is the sum of fixed and variable portion.
Reference to the superclass object.
The fixed portion of this charge element.
The kind of charge to be applied.
The variable portion of this charge element, calculated as a percentage of the total amount of a parent charge.
Parent of this charge sub-component.
A Charge Component is a list of configurable charge quality items to feed into settlement calculation and/or bill determinants.
A Charge Component is a list of configurable charge quality items to feed into settlement calculation and/or bill determinants.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
A BillDeterminant can have 0-n ChargeComponent and a ChargeComponent can associate to 0-n BillDeterminant.
Charge Group is the grouping of Charge Types for settlement invoicing purpose.
Charge Group is the grouping of Charge Types for settlement invoicing purpose. Examples such as Ancillary Services, Interests, etc.
Reference to the superclass object.
undocumented
undocumented
undocumented
A ChargeGroup instance can have relationships with other ChargeGroup instances.
undocumented
A type of profile for financial charges
A type of profile for financial charges
Reference to the superclass object.
The calculation frequency, daily or monthly.
The number of intervals in the profile data.
The type of profile. It could be amount, price, or quantity.
The unit of measure applied to the value attribute of the profile data.
undocumented
undocumented
undocumented
Model of various charges associated with an energy profile to support billing and settlement
Model of various charges associated with an energy profile to support billing and settlement
Reference to the superclass object.
The sequence number of the profile.
The date and time of an interval.
The value of an interval given a profile type (amount, price, or quantity), subject to the UOM.
undocumented
undocumented
Charge Type is the basic level configuration for settlement to process specific charges for invoicing purpose.
Charge Type is the basic level configuration for settlement to process specific charges for invoicing purpose. Examples such as: Day Ahead Spinning Reserve Default Invoice Interest Charge, etc.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
A ChargeType can have 0-n ChargeComponent and a ChargeComponent can associate to 0-n ChargeType
A ChargeGroup can have 0-n ChargeType. A ChargeType can associate to 0-n ChargeGroup.
undocumented
The actual tender when it is a type of cheque.
The actual tender when it is a type of cheque.
Reference to the superclass object.
Details of the account holder and bank.
Cheque reference number as printed on the cheque.
Date when cheque becomes valid.
Kind of cheque.
The magnetic ink character recognition number printed on the cheque.
Payment tender the cheque is being used for.
A Clamp is a galvanic connection at a line segment where other equipment is connected.
A Clamp is a galvanic connection at a line segment where other equipment is connected. A Clamp does not cut the line segment.
Reference to the superclass object.
The length to the place where the clamp is located starting from side one of the line segment, i.e. the line segment terminal with sequence number equal to 1.
The line segment to which the clamp is connected.
Action on clearance document as a switching step.
Action on clearance document as a switching step.
Reference to the superclass object.
Clearance action to perform.
Clearance associated with this clearance action.
Group to which this step belongs.
Safety document used to authorise work on conducting equipment in the field.
Safety document used to authorise work on conducting equipment in the field. Tagged equipment is not allowed to be operated.
Reference to the superclass object.
If true, the equipment must be deenergised.
If true, the equipment must be grounded.
Clearance action associated with this clearance.
All power system resources tagged through this clearance.
Participation factors per Cnode.
Participation factors per Cnode. Used to calculate "participation" of Cnode in an AggregateNode. Each Cnode associated to an AggregateNode would be assigned a participation factor for its participation within the AggregateNode.
Reference to the superclass object.
Used to calculate "participation" of Cnode in an AggregateNode
Point of delivery loss factor
undocumented
undocumented
undocumented
undocumented
A set of thermal generating units for the production of electrical energy and process steam (usually from the output of the steam turbines).
A set of thermal generating units for the production of electrical energy and process steam (usually from the output of the steam turbines). The steam sendout is typically used for industrial purposes or for municipal heating and cooling.
Reference to the superclass object.
The high pressure steam sendout.
The high pressure steam rating.
The low pressure steam sendout.
The low pressure steam rating.
The rated output active power of the cogeneration plant.
A cogeneration plant has a steam sendout schedule.
Communication function of communication equipment or a device such as a meter.
Communication function of communication equipment or a device such as a meter.
Reference to the superclass object.
Communication ID number (e.g. serial number, IP address, telephone number, etc.) of the AMR module which serves this meter.
Communication ID number (e.g. port number, serial number, data collector ID, etc.) of the parent device associated to this AMR module.
Kind of communication direction.
Kind of communication technology.
Module performing this communication function.
Communication media such as fibre optic cable, power-line, telephone, etc.
Communication media such as fibre optic cable, power-line, telephone, etc.
Reference to the superclass object.
An asset having communications capabilities that can be paired with a meter or other end device to provide the device with communication ability, through associated communication function.
An asset having communications capabilities that can be paired with a meter or other end device to provide the device with communication ability, through associated communication function. An end device that has communications capabilities through embedded hardware can use that function directly (without the communication module), or combine embedded communication function with additional communication functions provided through an external communication module (e.g. zigbee).
Reference to the superclass object.
Automated meter reading (AMR) system communicating with this com module.
If true, autonomous daylight saving time (DST) function is supported.
Time zone offset relative to GMT for the location of this com module.
Configuration options for combined cycle units.
Configuration options for combined cycle units. For example, a Combined Cycle with (CT1, CT2, ST1) will have (CT1, ST1) and (CT2, ST1) configurations as part of(1CT + 1STlogicalconfiguration).
Reference to the superclass object.
Whether this CombinedCycleConfiguration is the primary configuration in the associated Logical configuration?
undocumented
Whether Combined Cycle Plant can be shut-down in this Configuration?
Whether Combined Cycle Plant can be started in this Logical Configuration?
Configuration Member of CCP Configuration.
Configuration Member of CCP Configuration.
Reference to the superclass object.
primary configuration.
Steam plant.
undocumented
undocumented
Logical Configuration of a Combined Cycle plant.
Logical Configuration of a Combined Cycle plant. Operating Combined Cycle Plant (CCP) configurations are represented as Logical CCP Resources. Logical representation shall be used for Market applications to optimize and control Market Operations. Logical representation is also necessary for controlling the number of CCP configurations and to temper performance issues that may otherwise occur.
Reference to the superclass object.
undocumented
A set of combustion turbines and steam turbines where the exhaust heat from the combustion turbines is recovered to make steam for the steam turbines, resulting in greater overall plant efficiency.
A set of combustion turbines and steam turbines where the exhaust heat from the combustion turbines is recovered to make steam for the steam turbines, resulting in greater overall plant efficiency.
Reference to the superclass object.
The combined cycle plant's active power output rating.
Defines the available from and to Transition States for the Combine Cycle Configurations.
Defines the available from and to Transition States for the Combine Cycle Configurations.
Reference to the superclass object.
Flag indicating whether this is an UP transition. If not, it is a DOWN transition.
undocumented
undocumented
A prime mover that is typically fueled by gas or light oil.
A prime mover that is typically fueled by gas or light oil.
Reference to the superclass object.
Default ambient temperature to be used in modeling applications.
Off-nominal frequency effect on turbine auxiliaries. Per unit reduction in auxiliary active power consumption versus per unit reduction in frequency (from rated frequency).
Off-nominal voltage effect on turbine auxiliaries. Per unit reduction in auxiliary active power consumption versus per unit reduction in auxiliary bus voltage (from a specified voltage level).
Off-nominal frequency effect on turbine capability. Per unit reduction in unit active power capability versus per unit reduction in frequency (from rated frequency).
Flag that is set to true if the combustion turbine is associated with a heat recovery boiler.
Per unit change in power per (versus) unit change in ambient temperature.
Reference temperature at which the output of the turbine was defined.
The time constant for the turbine.
A CAES air compressor is driven by combustion turbine.
A combustion turbine may have an active power versus ambient temperature relationship.
A combustion turbine may have a heat recovery boiler for making steam.
A Command is a discrete control used for supervisory control.
A Command is a discrete control used for supervisory control.
Reference to the superclass object.
Normal value for Control.value e.g. used for percentage scaling.
The value representing the actuator output.
The MeasurementValue that is controlled.
The ValueAliasSet used for translation of a Control value to a name.
Models results of market clearing which call for commitment of units.
Models results of market clearing which call for commitment of units.
Reference to the superclass object.
Provides the necessary information (on a resource basis) to capture the Startup/Shutdown commitment results.
Provides the necessary information (on a resource basis) to capture the Startup/Shutdown commitment results. This information is relevant to all markets.
Reference to the superclass object.
the type of UC status (self commitment, ISO commitment, or SCUC commitment)
Total cost associated with changing the status of the resource.
Indicator of either a Start-Up or a Shut-Down.
End time for the commitment period. This will be on an interval boundary.
Start time for the commitment period. This will be on an interval boundary.
SCUC commitment period start-up time. Calculated start up time based on the StartUpTimeCurve provided with the Bid.
Unit no load cost in case of energy commodity
undocumented
undocumented
undocumented
undocumented
The connection to remote units is through one or more communication links.
The connection to remote units is through one or more communication links. Reduntant links may exist. The CommunicationLink class inherit PowerSystemResource. The intention is to allow CommunicationLinks to have Measurements. These Measurements can be used to model link status as operational, out of service, unit failure etc.
Reference to the superclass object.
A pre-planned job model containing labor, material, and accounting requirements for standardized job planning.
A pre-planned job model containing labor, material, and accounting requirements for standardized job planning.
Reference to the superclass object.
Estimated total cost for perfoming CU.
The quantity, unit of measure, and multiplier at the CU level that applies to the materials.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
Compliance events are used for reporting regulatory or contract compliance issues and/or variances.
Compliance events are used for reporting regulatory or contract compliance issues and/or variances. These might be created as a consequence of local business processes and associated rules. It is anticipated that this class will be customised extensively to meet local implementation needs.
Reference to the superclass object.
The deadline for compliance.
A model of a set of individual Switches normally enclosed within the same cabinet and possibly with interlocks that restrict the combination of switch positions.
A model of a set of individual Switches normally enclosed within the same cabinet and possibly with interlocks that restrict the combination of switch positions. These are typically found in medium voltage distribution networks.
Reference to the superclass object.
An alphanumeric code that can be used as a reference to extra information such as the description of the interlocking scheme if any.
Properties of a composite switch.
Properties of a composite switch.
Reference to the superclass object.
True if multi-phase switch controls all phases concurrently.
Initial operating mode, with the following values: Automatic, Manual.
Breaking capacity, or short circuit rating, is the maximum rated current which the device can safely interrupt at the rated voltage.
Kind of composite switch.
Phases carried, if applicable.
Supported number of phases, typically 0, 1 or 3.
Rated voltage.
True if device is capable of being operated by remote control.
Number of switch states represented by the composite switch.
Concentric neutral cable data.
Concentric neutral cable data.
Reference to the superclass object.
Diameter over the concentric neutral strands.
Number of concentric neutral strands.
Geometric mean radius of the neutral strand.
DC resistance per unit length of the neutral strand at 20 �C.
Outside radius of the neutral strand.
This is to specify the various condition factors for a design that may alter the cost estimate or the allocation.
This is to specify the various condition factors for a design that may alter the cost estimate or the allocation.
Reference to the superclass object.
The actual value of the condition factor, such as labor flat fee or percentage.
Kind of this condition factor.
undocumented
The parts of the AC power system that are designed to carry current or that are conductively connected through terminals.
The parts of the AC power system that are designed to carry current or that are conductively connected through terminals.
Reference to the superclass object.
Base voltage of this conducting equipment. Use only when there is no voltage level container used and only one base voltage applies. For example, not used for transformers.
Action involving grounding operation on this conducting equipment.
Jumper action involving jumping operation on this conducting equipment.
The status state variable associated with this conducting equipment.
Combination of conducting material with consistent electrical characteristics, building a single electrical system, used to carry current between points in the power system.
Combination of conducting material with consistent electrical characteristics, building a single electrical system, used to carry current between points in the power system.
Reference to the superclass object.
Segment length for calculating line section capabilities
Used to report details on creation, change or deletion of an entity or its configuration.
Used to report details on creation, change or deletion of an entity or its configuration.
Reference to the superclass object.
Date and time this event has or will become effective.
Source/initiator of modification.
Free text remarks.
Asset whose change resulted in this configuration event.
Document whose change resulted in this configuration event.
Location whose change resulted in this configuration event.
Organisation role whose change resulted in this configuration event.
Person role whose change resulted in this configuration event.
Service category whose change resulted in this configuration event.
Usage point whose change resulted in this configuration event.
ConformLoad represent loads that follow a daily load change pattern where the pattern can be used to scale the load with a system load.
ConformLoad represent loads that follow a daily load change pattern where the pattern can be used to scale the load with a system load.
Reference to the superclass object.
Group of this ConformLoad.
A group of loads conforming to an allocation pattern.
A group of loads conforming to an allocation pattern.
Reference to the superclass object.
A curve of load versus time (X-axis) showing the active power values (Y1-axis) and reactive power (Y2-axis) for each unit of the period covered.
A curve of load versus time (X-axis) showing the active power values (Y1-axis) and reactive power (Y2-axis) for each unit of the period covered. This curve represents a typical pattern of load over the time period for a given day type and season.
Reference to the superclass object.
The ConformLoadGroup where the ConformLoadSchedule belongs.
Designated Congestion Area Definition (DCA)
Designated Congestion Area Definition (DCA)
Reference to the superclass object.
undocumented
A function that will disconnect and reconnect the customer's load under defined conditions.
A function that will disconnect and reconnect the customer's load under defined conditions.
Reference to the superclass object.
Running cumulative count of connect or disconnect events, for the lifetime of this function or until the value is cleared.
True if this function is in the connected state.
If set true, the switch may disconnect the service at the end of a specified time delay after the disconnect signal has been given. If set false, the switch may disconnect the service immediately after the disconnect signal has been given. This is typically the case for over current circuit-breakers which are classified as either instantaneous or slow acting.
If set true and if disconnection can be operated locally, the operation happens automatically. Otherwise it happens manually.
If set true and if reconnection can be operated locally, then the operation happens automatically. Otherwise, it happens manually.
If set true and if disconnection can be operated remotely, then the operation happens automatically. If set false and if disconnection can be operated remotely, then the operation happens manually.
If set true and if reconnection can be operated remotely, then the operation happens automatically. If set false and if reconnection can be operated remotely, then the operation happens manually.
Information on remote connect disconnect switch.
undocumented
Connectivity nodes are points where terminals of AC conducting equipment are connected together with zero impedance.
Connectivity nodes are points where terminals of AC conducting equipment are connected together with zero impedance.
Reference to the superclass object.
Container of this connectivity node.
The topological node to which this connectivity node is assigned. May depend on the current state of switches in the network.
A base class for all objects that may contain connectivity nodes or topological nodes.
A base class for all objects that may contain connectivity nodes or topological nodes.
Reference to the superclass object.
A conductor, or group of conductors, with negligible impedance, that serve to connect other conducting equipment within a single substation and are modelled with a single logical terminal.
A conductor, or group of conductors, with negligible impedance, that serve to connect other conducting equipment within a single substation and are modelled with a single logical terminal.
Reference to the superclass object.
Groups all items associated with Binding Constraints and Constraint Violations per interval and market.
Groups all items associated with Binding Constraints and Constraint Violations per interval and market.
Reference to the superclass object.
Provides the Market results for the constraint processing for either the DAM or RTM.
Provides the Market results for the constraint processing for either the DAM or RTM. The data includes the constraint type (binding or violated), the solved value for the constraint, and the associated shadow price.
Reference to the superclass object.
Branch base Power Flow.
MW Limit.
Cleared MW.
Non-competitive path constraint Flag"(Y/N) indicating whether the shadow price on a non-competitive path was non-zero.
Type of constraint.
Limit flag ('Maximum', 'Minimum').
Included in optimization Y/N.
Transmission overload MW.
Actual MW flow as percent of limit.
Shadow Price ($/MW) for the commodity. Shadow price for the corresponding constraint.
Update time stamp.
MQS change type.
Updated user.
This value is determined in DA and RTM. The SCUC optimization ensures that the MW flow on the Branch Group will not exceed this limit in the relevant direction.
Branch Group TR Reservation Capacity - This value is determined in DA and RTM. It is the amount of spare transmission capacity that is left for the TR holder to use.
undocumented
undocumented
undocumented
A constraint term is one element of a linear constraint.
A constraint term is one element of a linear constraint.
Reference to the superclass object.
undocumented
The function is an enumerated value that can be 'active', 'reactive', or 'VA' to indicate the type of flow.
undocumented
One of a sequence of intervals defined in terms of consumption quantity of a service such as electricity, water, gas, etc.
One of a sequence of intervals defined in terms of consumption quantity of a service such as electricity, water, gas, etc. It is typically used in association with TariffProfile to define the steps or blocks in a step tariff structure, where startValue simultaneously defines the entry value of this step and the closing value of the previous step. Where consumption is >= startValue it falls within this interval and where consumption is < startValue it falls within the previous interval.
Reference to the superclass object.
A sequential reference that defines the identity of this interval and its relative position with respect to other intervals in a sequence of intervals.
The lowest level of consumption that defines the starting point of this interval. The interval extends to the start of the next interval or until it is reset to the start of the first interval by TariffProfile.tariffCycle.
All charges used to define this consumption tariff interval.
All time of use tariff intervals influenced by this consumption tariff interval.
An event threatening system reliability, consisting of one or more contingency elements.
An event threatening system reliability, consisting of one or more contingency elements.
Reference to the superclass object.
Set true if must study this contingency.
Possibly time-varying max MW or MVA and optionally Min MW limit or MVA limit (Y1 and Y2, respectively) assigned to a constraint for a specific contingency.
Possibly time-varying max MW or MVA and optionally Min MW limit or MVA limit (Y1 and Y2, respectively) assigned to a constraint for a specific contingency. Use CurveSchedule XAxisUnits to specify MW or MVA.
Reference to the superclass object.
undocumented
undocumented
undocumented
An element of a system event to be studied by contingency analysis, representing a change in status of a single piece of equipment.
An element of a system event to be studied by contingency analysis, representing a change in status of a single piece of equipment.
Reference to the superclass object.
A contingency element belongs to one contingency.
A equipment to which the in service status is to change such as a power transformer or AC line segment.
A equipment to which the in service status is to change such as a power transformer or AC line segment.
Reference to the superclass object.
The status for the associated equipment when in the contingency state. This status is independent of the case to which the contingency is originally applied, but defines the equipment status when the contingency is applied.
The single piece of equipment to which to apply the contingency.
Distribution amoung resources at the sink point or source point
Distribution amoung resources at the sink point or source point
Reference to the superclass object.
MW value that this resource provides to the overall contract.
This value will be set to YES if the referenced Cnode is defined as the sink point in the contract.
This value will be set to YES if the referenced Cnode is defined as the source point in the contract.
undocumented
undocumented
undocumented
Provides definition of Transmission Ownership Right and Existing Transmission Contract identifiers for use by SCUC.
Provides definition of Transmission Ownership Right and Existing Transmission Contract identifiers for use by SCUC. RMR contract hosting: Startup lead time, Contract Service Limits, Max Service Hours, Max MWhs, Max Start-ups, Ramp Rate, Max Net Dependable Capacity, Min Capacity and Unit Substitution for DAM/RTM to retrieve;
Reference to the superclass object.
When used in conjunction with a Transmission Right contract chain, this is the precedence for the contracts.
MW value of the contract
Financial value of the contract
Priority for the contract. This should be unique amoung all contracts for a specific resource. This value is the directive for the SCUC algorithm on the order to satisfy/cut contracts.
Contract status
type of the contract. Possible values are but not limited by:
end effective date
Indicator if the location associated with this contract is financial (e.g. pricing nodes) or physical (e.g. connectivity nodes).
Flag to indicate this contract provides financial rights in the DA Market
Flag to indicate this contract provides financial rights in the RT Market
Estimated Fuel Adder
This indicates the latest schedule minutes (e.g. t - xx) that this resource can be notified to respond. This attribute is only used if the market type is not supplied.
This indicates the latest schedule market type a contract can be applied to. This is used in conjunction with the latestSchedMinutes attribute to determine the latest time this contract can be called in. The possible values for this attribute are: DAM, RTM or it can be omitted. If omitted, the latestSchedMinutes attribute defines the value.
Maximum Net Dependable Capacity
Maximum schedule MW quantity
Maximum service hours
Maximum startups
Minimum Load
Minimum schedule quanity
Flag to indicate this contract provides physical rights in the DA Market
Flag to indicate this contract provides physical rights in the RT Market
start effective date
Start up lead time
undocumented
undocumented
undocumented
undocumented
Transmission Right type - is this an individual contract right or a chain contract right. Types = CHAIN or INDIVIDUAL
Contractor information for work task.
Contractor information for work task.
Reference to the superclass object.
Activity code identifies a specific and distinguishable unit of work.
The amount that a given contractor will charge for performing this unit of work.
The total amount charged.
undocumented
undocumented
undocumented
undocumented
Control is used for supervisory/device control.
Control is used for supervisory/device control. It represents control outputs that are used to change the state in a process, e.g. close or open breaker, a set point value or a raise lower command.
Reference to the superclass object.
Specifies the type of Control, e.g. BreakerOn/Off, GeneratorVoltageSetPoint, TieLineFlow etc. The ControlType.name shall be unique among all specified types and describe the type.
Indicates that a client is currently sending control commands that has not completed.
The last time a control output was sent.
The unit multiplier of the controlled quantity.
The unit of measure of the controlled quantity.
Regulating device governed by this control output.
The remote point controlling the physical actuator.
A control area is a grouping of generating units and/or loads and a cutset of tie lines (as terminals) which may be used for a variety of purposes including automatic generation control, powerflow solution area interchange control specification, and input to load forecasting.
A control area is a grouping of generating units and/or loads and a cutset of tie lines (as terminals) which may be used for a variety of purposes including automatic generation control, powerflow solution area interchange control specification, and input to load forecasting. Note that any number of overlapping control area specifications can be superimposed on the physical model.
Reference to the superclass object.
The specified positive net interchange into the control area, i.e. positive sign means flow in to the area.
Active power net interchange tolerance
The primary type of control area definition used to determine if this is used for automatic generation control, for planning interchange control, or other purposes. A control area specified with primary type of automatic generation control could still be forecast and used as an interchange area in power flow analysis.
The energy area that is forecast from this control area specification.
Indicates Control Area associated with self-schedule.
Indicates Control Area associated with self-schedule.
Reference to the superclass object.
Attained.
Native.
undocumented
undocumented
A control area generating unit.
A control area generating unit. This class is needed so that alternate control area definitions may include the same generating unit. Note only one instance within a control area should reference a specific generating unit.
Reference to the superclass object.
The parent control area for the generating unit specifications.
The generating unit specified for this control area. Note that a control area should include a GeneratingUnit only once.
Operates the Control Area.
Operates the Control Area. Approves and implements energy transactions. Verifies both Inter-Control Area and Intra-Control Area transactions for the power system before granting approval (and implementing) the transactions.
Reference to the superclass object.
A ControlAreaOperator has a collection of tie points that ring the ControlArea, called a TieLine.
A ControlAreaCompany controls a ControlArea.
State Estimator Solution Pool Interchange and Losses
State Estimator Solution Pool Interchange and Losses
Reference to the superclass object.
Pool MW Interchange Attribute Usage: The active power interchange of the pool
Pool Losses MW Attribute Usage: The active power losses of the pool in MW
undocumented
Appliance controlled with a PAN device control.
Appliance controlled with a PAN device control.
Reference to the superclass object.
True if the appliance is an electric vehicle.
True if the appliance is exterior lighting.
True if the appliance is a generation system.
True if the appliance is HVAC compressor or furnace.
True if the appliance is interior lighting.
True if the appliance is an irrigation pump.
True if the appliance is managed commercial or industrial load.
True if the appliance is a pool, pump, spa or jacuzzi.
True if the appliance is a simple miscellaneous load.
True if the appliance is a smart appliance.
True if the appliance is a stip or baseboard heater.
True if the appliance is a water heater.
There are often stages of power which are associated with stages of cooling.
There are often stages of power which are associated with stages of cooling. For instance, a transformer may be rated 121kV on the primary, 15kV on the secondary and 4kV on the tertiary winding. These are voltage ratings and the power ratings are generally the same for all three windings and independent of the voltage ratings, there are instances where the tertiary may have a lower power rating.
Reference to the superclass object.
Kind of cooling system.
The power rating associated with type of cooling specified for this stage.
Stage of cooling and associated power rating.
undocumented
Coordinate reference system.
Coordinate reference system.
Reference to the superclass object.
A Uniform Resource Name (URN) for the coordinate reference system (crs) used to define 'Location. PositionPoints'.
A categorization for resources, often costs, in accounting transactions.
A categorization for resources, often costs, in accounting transactions. Examples include: material components, building in service, coal sales, overhead, etc.
Reference to the superclass object.
True if an amount can be assigned to the resource element (e.g., building in service, transmission plant, software development capital); false otherwise (e.g., internal labor, material components).
A codified representation of the resource element.
The level of the resource element in the hierarchy of resource elements (recursive relationship).
The stage for which this costType applies: estimated design, estimated actual or actual actual.
undocumented
undocumented
undocumented
Craft of a person or a crew.
Craft of a person or a crew. Examples include overhead electric, underground electric, high pressure gas, etc. This ensures necessary knowledge and skills before being allowed to perform certain types of work.
Reference to the superclass object.
undocumented
Classification by utility's work mangement standards and practices.
undocumented
Group of people with specific skills, tools, and vehicles.
Group of people with specific skills, tools, and vehicles.
Reference to the superclass object.
Status of this crew.
Type of this crew.
Member of a crew.
Member of a crew.
Reference to the superclass object.
Crew to which this crew member belongs.
Custom description of the type of crew.
Custom description of the type of crew. This may be used to determine the type of work the crew can be assigned to. Examples include repair, tree trimming, switching, etc.
Reference to the superclass object.
DC side of the current source converter (CSC).
DC side of the current source converter (CSC).
Reference to the superclass object.
Firing angle, typical value between 10 and 18 degrees for a rectifier. CSC state variable, result from power flow.
Extinction angle. CSC state variable, result from power flow.
Maximum firing angle. CSC configuration data used in power flow.
Maximum extinction angle. CSC configuration data used in power flow.
The maximum direct current (Id) on the DC side at which the converter should operate. Converter configuration data use in power flow.
Minimum firing angle. CSC configuration data used in power flow.
Minimum extinction angle. CSC configuration data used in power flow.
The minimum direct current (Id) on the DC side at which the converter should operate. CSC configuration data used in power flow.
Indicates whether the DC pole is operating as an inverter or as a rectifier. CSC control variable used in power flow.
undocumented
Rated converter DC current, also called IdN. Converter configuration data used in power flow.
Target firing angle. CSC control variable used in power flow.
Target extinction angle. CSC control variable used in power flow.
DC current target value. CSC control variable used in power flow.
Control area emergency schedules
Control area emergency schedules
Reference to the superclass object.
Net tie MW. These are three entries, the current emergency schedule interchange and the two future schedules if they exist.
Ramp time, the ramping time for a schedule. This is calculated as the remaining time to ramp if a schedule is ramping. Measured in seconds, but can be negattive.
Net tie time, the start time for a schedule. This is calculated as the current time if a schedule is ramping.
undocumented
Operational limit on current.
Operational limit on current.
Reference to the superclass object.
Limit on current flow.
A device that checks current flow values in any direction or designated direction.
A device that checks current flow values in any direction or designated direction.
Reference to the superclass object.
Current limit number one 1 for inverse time pickup.
Current limit number 2 for inverse time pickup.
Current limit number 3 for inverse time pickup.
Set true if the current relay has inverse time characteristic.
Inverse time delay number 1 for current limit number 1.
Inverse time delay number 2 for current limit number 2.
Inverse time delay number 3 for current limit number 3.
Control area current net tie (scheduled interchange) sent to real time dispatch.
Control area current net tie (scheduled interchange) sent to real time dispatch.
Reference to the superclass object.
Current control area net tie MW (the sum of the tie line flows, i.e the sum of flows into and out of the control area), the current instantaneous scheduled interchange.
Use Emergency Schedule Attribute Usage: Emergency use indicator, false = Emergency Schedular OFF, true = Emergency Schedular ON.
undocumented
Instrument transformer used to measure electrical qualities of the circuit that is being protected and/or monitored.
Instrument transformer used to measure electrical qualities of the circuit that is being protected and/or monitored. Typically used as current transducer for the purpose of metering or protection. A typical secondary current rating would be 5A.
Reference to the superclass object.
CT accuracy classification.
Percent of rated current for which the CT remains accurate within specified limits.
Power burden of the CT core.
CT classification; i.e. class 10P.
Intended usage of the CT; i.e. metering, protection.
Properties of current transformer asset.
Properties of current transformer asset.
Reference to the superclass object.
CT accuracy classification.
Accuracy limit.
Number of cores.
undocumented
Maximum primary current where the CT still displays linear characteristicts.
Maximum voltage across the secondary terminals where the CT still displays linear characteristicts.
Maximum ratio between the primary and secondary current.
Nominal ratio between the primary and secondary current; i.e. 100:5.
Full load secondary (FLS) rating for primary winding.
Ratio for the primary winding tap changer.
Rated current on the primary side.
Full load secondary (FLS) rating for secondary winding.
Ratio for the secondary winding tap changer.
Full load secondary (FLS) rating for tertiary winding.
Ratio for the tertiary winding tap changer.
Usage: eg. metering, protection, etc.
Curtailing entity must be providing at least one service to the EnergyTransaction.
Curtailing entity must be providing at least one service to the EnergyTransaction. The CurtailmentProfile must be completely contained within the EnergyProfile timeframe for this EnergyTransaction.
Reference to the superclass object.
An EnergyTransaction may be curtailed by any of the participating entities.
A multi-purpose curve or functional relationship between an independent variable (X-axis) and dependent (Y-axis) variables.
A multi-purpose curve or functional relationship between an independent variable (X-axis) and dependent (Y-axis) variables.
Reference to the superclass object.
The style or shape of the curve.
Multiplier for X-axis.
The X-axis units of measure.
Multiplier for Y1-axis.
The Y1-axis units of measure.
Multiplier for Y2-axis.
The Y2-axis units of measure.
Multiplier for Y3-axis.
The Y3-axis units of measure.
Multi-purpose data points for defining a curve.
Multi-purpose data points for defining a curve. The use of this generic class is discouraged if a more specific class can be used to specify the x and y axis values along with their specific data types.
Reference to the superclass object.
The data value of the X-axis variable, depending on the X-axis units.
The data value of the first Y-axis variable, depending on the Y-axis units.
The data value of the second Y-axis variable (if present), depending on the Y-axis units.
The data value of the third Y-axis variable (if present), depending on the Y-axis units.
The curve of this curve data point.
Organisation receiving services from service supplier.
Organisation receiving services from service supplier.
Reference to the superclass object.
Kind of customer.
Locale designating language to use in communications with this customer.
Priority of the customer.
(if applicable) Public utilities commission (PUC) identification number.
True if customer organisation has special service needs such as life support, hospitals, etc.
Status of this customer.
(use 'priority' instead) True if this is an important customer. Importance is for matters different than those in 'specialNeed' attribute.
All the works performed for this customer.
Assignment of a group of products and services purchased by the customer through a customer agreement, used as a mechanism for customer billing and payment.
Assignment of a group of products and services purchased by the customer through a customer agreement, used as a mechanism for customer billing and payment. It contains common information from the various types of customer agreements to create billings (invoices) for a customer and receive payment.
Reference to the superclass object.
Cycle day on which the associated customer account will normally be billed, used to determine when to produce the billing.
Budget bill code.
Customer owning this account.
Agreement between the customer and the service supplier to pay for service at a specific service location.
Agreement between the customer and the service supplier to pay for service at a specific service location. It records certain billing information about the type of service provided at the service location and is used during charge creation to determine the type of service.
Reference to the superclass object.
Load management code.
Customer for this agreement.
Customer account owning this agreement.
All pricing structures applicable to this customer agreement.
Service category for this agreement.
All service locations regulated by this customer agreement.
Service supplier for this customer agreement.
undocumented
The creation of the monthly customer billing statements is the method employed to notify Customers of charges, adjustments and credits applied to their account for Services and Products.
The creation of the monthly customer billing statements is the method employed to notify Customers of charges, adjustments and credits applied to their account for Services and Products. The actuall billing occurs through an ErpInvoice. The CustomerBillingInfo includes information from the payment, collection, meter reading, installed meter, service, site, customer, customer account, customer agreement, services and pricing subject areas. Each component price shows up as a separate line item on the ErpInvoice.
Reference to the superclass object.
Business date designated for the billing run which produced this CustomerBillingInfo.
Calculated date upon which a customer billing amount is due, used in the invoicing process to determine when a Customer's Payment is delinquent. It takes into consideration the regulatory criteria and the Customer's requested due date. In the absence of a Customer requested due date, the due date is typically calculated from the regulated number of days and the 'billingDate'.
Kind of bill customer receives.
Amount of the last payment received from the customer. It is retained in the Customer Billing system, although the details of each payment are tracked in the ERP system.
Date of the last payment received from the customer. It is retained in the Customer Billing system, although the details of each payment are tracked in the ERP system.
Outstanding balance on the CustomerAccount as of the statement date.
Monthly amortized amount due during each billing cycle for the CustomerAccount balance for which the Payment Plan is set-up.
Type of payment plan.
undocumented
undocumented
The energy buyer in the energy marketplace.
The energy buyer in the energy marketplace.
Reference to the superclass object.
Conditions for notifying the customer about the changes in the status of their service (e.g., outage restore, estimated restoration time, tariff or service level change, etc.)
Conditions for notifying the customer about the changes in the status of their service (e.g., outage restore, estimated restoration time, tariff or service level change, etc.)
Reference to the superclass object.
Type of contact (e.g., phone, email, etc.).
Value of contact type (e.g., phone number, email address, etc.).
Earliest date time to call the customer.
Latest date time to call the customer.
Trigger for this notification.
Customer requiring this notification.
Incident as a subject of this customer notification.
A cut separates a line segment into two parts.
A cut separates a line segment into two parts. The cut appears as a switch inserted between these two parts and connects them together. As the cut is normally open there is no galvanic connection between the two line segment parts. But it is possible to close the cut to get galvanic connection.
Reference to the superclass object.
The length to the place where the cut is located starting from side one of the cut line segment, i.e. the line segment Terminal with sequenceNumber equal to 1.
The line segment to which the cut is applied.
Action taken with this cut.
Action on cut as a switching step.
Action on cut as a switching step.
Reference to the superclass object.
Switching action to perform.
Cut on which this action is taken.
Group to which this step belongs.
An electrical connection point at a piece of DC conducting equipment.
An electrical connection point at a piece of DC conducting equipment. DC terminals are connected at one physical DC node that may have multiple DC terminals connected. A DC node is similar to an AC connectivity node. The model enforces that DC connections are distinct from AC connections.
Reference to the superclass object.
undocumented
See association end Terminal. TopologicalNode.
A breaker within a DC system.
A breaker within a DC system.
Reference to the superclass object.
A busbar within a DC system.
A busbar within a DC system.
Reference to the superclass object.
Low resistance equipment used in the internal DC circuit to balance voltages.
Low resistance equipment used in the internal DC circuit to balance voltages. It has typically positive and negative pole terminals and a ground.
Reference to the superclass object.
The parts of the DC power system that are designed to carry current or that are conductively connected through DC terminals.
The parts of the DC power system that are designed to carry current or that are conductively connected through DC terminals.
Reference to the superclass object.
Indivisible operative unit comprising all equipment between the point of common coupling on the AC side and the point of common coupling � DC side, essentially one or more converters, together with one or more converter transformers, converter control equipment, essential protective and switching devices and auxiliaries, if any, used for conversion.
Indivisible operative unit comprising all equipment between the point of common coupling on the AC side and the point of common coupling � DC side, essentially one or more converters, together with one or more converter transformers, converter control equipment, essential protective and switching devices and auxiliaries, if any, used for conversion.
Reference to the superclass object.
undocumented
undocumented
A disconnector within a DC system.
A disconnector within a DC system.
Reference to the superclass object.
A modeling construct to provide a root class for containment of DC as well as AC equipment.
A modeling construct to provide a root class for containment of DC as well as AC equipment. The class differ from the EquipmentContaner for AC in that it may also contain DCNodes. Hence it can contain both AC and DC equipment.
Reference to the superclass object.
A ground within a DC system.
A ground within a DC system.
Reference to the superclass object.
Inductance to ground.
Resistance to ground.
Overhead lines and/or cables connecting two or more HVDC substations.
Overhead lines and/or cables connecting two or more HVDC substations.
Reference to the superclass object.
undocumented
A wire or combination of wires not insulated from one another, with consistent electrical characteristics, used to carry direct current between points in the DC region of the power system.
A wire or combination of wires not insulated from one another, with consistent electrical characteristics, used to carry direct current between points in the DC region of the power system.
Reference to the superclass object.
Capacitance of the DC line segment. Significant for cables only.
Inductance of the DC line segment. Neglectable compared with DCSeriesDevice used for smoothing.
Segment length for calculating line section capabilities.
Resistance of the DC line segment.
Set of per-length parameters for this line segment.
DC nodes are points where terminals of DC conducting equipment are connected together with zero impedance.
DC nodes are points where terminals of DC conducting equipment are connected together with zero impedance.
Reference to the superclass object.
undocumented
See association end ConnectivityNode. TopologicalNode.
A series device within the DC system, typically a reactor used for filtering or smoothing.
A series device within the DC system, typically a reactor used for filtering or smoothing. Needed for transient and short circuit studies.
Reference to the superclass object.
Inductance of the device.
Rated DC device voltage. Converter configuration data used in power flow.
Resistance of the DC device.
A shunt device within the DC system, typically used for filtering.
A shunt device within the DC system, typically used for filtering. Needed for transient and short circuit studies.
Reference to the superclass object.
Capacitance of the DC shunt.
Rated DC device voltage. Converter configuration data used in power flow.
Resistance of the DC device.
A switch within the DC system.
A switch within the DC system.
Reference to the superclass object.
An electrical connection point to generic DC conducting equipment.
An electrical connection point to generic DC conducting equipment.
Reference to the superclass object.
undocumented
An electrically connected subset of the network.
An electrically connected subset of the network. DC topological islands can change as the current network state changes: e.g. due to
Reference to the superclass object.
DC bus.
DC bus.
Reference to the superclass object.
undocumented
undocumented
The date and or the time.
The date and or the time.
Reference to the superclass object.
Date as "yyyy-mm-dd", which conforms with ISO 8601
Time as "hh:mm:ss.sssZ", which conforms with ISO 8601.
Interval between two dates.
Interval between two dates.
Reference to the superclass object.
End date of this interval.
Start date of this interval.
Interval between two date and time points.
Interval between two date and time points.
Reference to the superclass object.
End date and time of this interval.
Start date and time of this interval.
Group of similar days.
Group of similar days. For example it could be used to represent weekdays, weekend, or holidays.
Reference to the superclass object.
DefaultBid is a generic class to hold Default Energy Bid, Default Startup Bid, and Default Minimum Load Bid:
DefaultBid is a generic class to hold Default Energy Bid, Default Startup Bid, and Default Minimum Load Bid:
Default Energy Bid A Default Energy Bid is a monotonically increasing staircase function consisting at maximum 10 economic bid segments, or 10 ($/MW, MW) pairs. There are three methods for determining the Default Energy Bid:
Reference to the superclass object.
Default bid type such as Default Energy Bid, Default Minimum Load Bid, and Default Startup Bid
Minimum load cost in $/hr
on-peak, off-peak, or all
undocumented
undocumented
Default bid curve for default energy bid curve and default startup curves (cost and time)
Default bid curve for default energy bid curve and default startup curves (cost and time)
Reference to the superclass object.
To indicate a type used for a default energy bid curve, such as LMP, cost or consultative based.
Default energy bid adder flag
undocumented
Curve data for default bid curve and startup cost curve.
Curve data for default bid curve and startup cost curve.
Reference to the superclass object.
Type of calculation basis used to define the default bid segment curve.
Possibly time-varying max MW or MVA and optionally Min MW limit or MVA limit (Y1 and Y2, respectively) applied as a default value if no specific constraint limits are specified for a contingency analysis.
Possibly time-varying max MW or MVA and optionally Min MW limit or MVA limit (Y1 and Y2, respectively) applied as a default value if no specific constraint limits are specified for a contingency analysis. Use CurveSchedule XAxisUnits to specify MW or MVA.
Reference to the superclass object.
undocumented
Demand response program.
Demand response program.
Reference to the superclass object.
Type of demand response program; examples are CPP (critical-peak pricing), RTP (real-time pricing), DLC (direct load control), DBP (demand bidding program), BIP (base interruptible program). Note that possible types change a lot and it would be impossible to enumerate them all.
Interval within which the program is valid.
All customer agreements through which the customer is enrolled in this demand response program.
All groups of end devices enrolled in this demand response program.
All usage point groups enrolled in this demand response program.
Identity contain comon descriptive information.
Identity contain comon descriptive information.
Reference to the superclass object.
undocumented
undocumented
undocumented
A design for consideration by customers, potential customers, or internal work.
A design for consideration by customers, potential customers, or internal work. Note that the Version of design is the revision attribute that is inherited from Document.
Reference to the superclass object.
Estimated cost (not price) of design.
Kind of this design.
Price to customer for implementing design.
undocumented
undocumented
undocumented
A logical part of the design (e.g., pole and all equipment on a pole).
A logical part of the design (e.g., pole and all equipment on a pole). This includes points and spans.
Reference to the superclass object.
The legth of the span from the previous pole to this pole.
undocumented
undocumented
Compatible unit at a given design location.
Compatible unit at a given design location.
Reference to the superclass object.
A code that helps direct accounting (capital, expense, or accounting treatment).
A code that instructs the crew what action to perform.
The quantity of the CU being assigned to this location.
As the same CU can be used for different purposes and accounting purposes, usage must be specified. Examples include: distribution, transmission, substation.
Year when a CU that represents an asset is removed.
undocumented
True if associated electrical equipment is intended to be energized while work is being performed.
undocumented
undocumented
undocumented
undocumented
undocumented
The result of a problem (typically an asset failure) diagnosis.
The result of a problem (typically an asset failure) diagnosis.
Reference to the superclass object.
Effect of problem.
Failuer mode, for example: Failure to Insulate; Failure to conduct; Failure to contain oil; Failure to provide ground plane; Other.
Cause of problem determined during diagnosis.
Code for diagnosed probem type.
Origin of problem determined during diagnosis.
Remarks pertaining to findings during problem diagnosis.
Phase(s) diagnosed.
Code for problem type determined during preliminary assessment.
Date and time preliminary assessment of problem was performed.
Remarks pertaining to preliminary assessment of problem.
Root cause of problem determined during diagnosis.
Root origin of problem determined during diagnosis.
Remarks pertaining to root cause findings during problem diagnosis.
The diagram being exchanged.
The diagram being exchanged. The coordinate system is a standard Cartesian coordinate system and the orientation attribute defines the orientation.
Reference to the superclass object.
Coordinate system orientation of the diagram.
X coordinate of the first corner of the initial view.
X coordinate of the second corner of the initial view.
Y coordinate of the first corner of the initial view.
Y coordinate of the second corner of the initial view.
A Diagram may have a DiagramStyle.
An object that defines one or more points in a given space.
An object that defines one or more points in a given space. This object can be associated with anything that specializes IdentifiedObject. For single line diagrams such objects typically include such items as analog values, breakers, disconnectors, power transformers, and transmission lines.
Reference to the superclass object.
The drawing order of this element. The higher the number, the later the element is drawn in sequence. This is used to ensure that elements that overlap are rendered in the correct order.
Defines whether or not the diagram objects points define the boundaries of a polygon or the routing of a polyline. If this value is true then a receiving application should consider the first and last points to be connected.
The offset in the X direction. This is used for defining the offset from centre for rendering an icon (the default is that a single point specifies the centre of the icon).
The offset in the Y direction. This is used for defining the offset from centre for rendering an icon (the default is that a single point specifies the centre of the icon).
Sets the angle of rotation of the diagram object. Zero degrees is pointing to the top of the diagram. Rotation is clockwise.
A diagram object is part of a diagram.
A diagram object has a style associated that provides a reference for the style used in the originating system.
The domain object to which this diagram object is associated.
A diagram object can be part of multiple visibility layers.
This is used for grouping diagram object points from different diagram objects that are considered to be glued together in a diagram even if they are not at the exact same coordinates.
This is used for grouping diagram object points from different diagram objects that are considered to be glued together in a diagram even if they are not at the exact same coordinates.
Reference to the superclass object.
A point in a given space defined by 3 coordinates and associated to a diagram object.
A point in a given space defined by 3 coordinates and associated to a diagram object. The coordinates may be positive or negative as the origin does not have to be in the corner of a diagram.
Reference to the superclass object.
The sequence position of the point, used for defining the order of points for diagram objects acting as a polyline or polygon with more than one point.
The X coordinate of this point.
The Y coordinate of this point.
The Z coordinate of this point.
The diagram object with which the points are associated.
The 'glue' point to which this point is associated.
A reference to a style used by the originating system for a diagram object.
A reference to a style used by the originating system for a diagram object. A diagram object style describes information such as line thickness, shape such as circle or rectangle etc, and color.
Reference to the superclass object.
The diagram style refer to a style used by the originating system for a diagram.
The diagram style refer to a style used by the originating system for a diagram. A diagram style describes information such as schematic, geographic, bus-branch etc.
Reference to the superclass object.
As applicable, the basic linear, area, or volume dimensions of an asset, asset type (AssetModel) or other type of object (such as land area).
As applicable, the basic linear, area, or volume dimensions of an asset, asset type (AssetModel) or other type of object (such as land area). Units and multipliers are specified per dimension.
Reference to the superclass object.
A description of the orientation of the object relative to the dimensions. As an example, a vault may have north-south orientation for the sizeLength measurement and sizeDepth may be the height of the vault.
Depth measurement.
Diameter measurement.
Length measurement.
Width measurement.
undocumented
The class represents IEEE Type DEC1A discontinuous excitation control model that boosts generator excitation to a level higher than that demanded by the voltage regulator and stabilizer immediately following a system fault.
The class represents IEEE Type DEC1A discontinuous excitation control model that boosts generator excitation to a level higher than that demanded by the voltage regulator and stabilizer immediately following a system fault. Reference: IEEE Standard 421.5-2005 Section 12.2.
Reference to the superclass object.
Speed change reference (ESC). Typical Value = 0.0015.
Discontinuous controller gain (KAN). Typical Value = 400.
Terminal voltage limiter gain (KETL). Typical Value = 47.
Discontinuous controller time constant (TAN). Typical Value = 0.08.
Time constant (TD). Typical Value = 0.03.
Time constant (TL1). Typical Value = 0.025.
Time constant (TL2). Typical Value = 1.25.
DEC washout time constant (TW5). Typical Value = 5.
Limiter for Van (VANMAX).
Limiter (VOMAX). Typical Value = 0.3.
Limiter (VOMIN). Typical Value = 0.1.
Limiter (VSMAX). Typical Value = 0.2.
Limiter (VSMIN). Typical Value = -0.066.
Terminal voltage level reference (VTC). Typical Value = 0.95.
Voltage reference (VTLMT). Typical Value = 1.1.
Voltage limits (VTM). Typical Value = 1.13.
Voltage limits (VTN). Typical Value = 1.12.
Regulator voltage reference (VAL). Typical Value = 5.5.
The class represents IEEE Type DEC2A model for the discontinuous excitation control.
The class represents IEEE Type DEC2A model for the discontinuous excitation control. This system provides transient excitation boosting via an open-loop control as initiated by a trigger signal generated remotely.
Reference to the superclass object.
Discontinuous controller time constant (TD1).
Discontinuous controller washout time constant (TD2).
Limiter (VDMAX).
Limiter (VDMIN).
Discontinuous controller input reference (VK).
The class represents IEEE Type DEC3A model.
The class represents IEEE Type DEC3A model. In some systems, the stabilizer output is disconnected from the regulator immediately following a severe fault to prevent the stabilizer from competing with action of voltage regulator during the first swing.
Reference to the superclass object.
Reset time delay (TDR).
Terminal undervoltage comparison level (VTMIN).
A manually operated or motor operated mechanical switching device used for changing the connections in a circuit, or for isolating a circuit or equipment from a source of power.
A manually operated or motor operated mechanical switching device used for changing the connections in a circuit, or for isolating a circuit or equipment from a source of power. It is required to open or close circuits when negligible current is broken or made.
Reference to the superclass object.
Discontinuous excitation control function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model</font>.
Discontinuous excitation control function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model</font>.
Reference to the superclass object.
Excitation system model with which this discontinuous excitation control model is associated.
Remote input signal used by this discontinuous excitation control system model.
Discontinuous excitation control function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Discontinuous excitation control function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Discrete represents a discrete Measurement, i.e.
Discrete represents a discrete Measurement, i.e. a Measurement representing discrete values, e.g. a Breaker position.
Reference to the superclass object.
Normal value range maximum for any of the MeasurementValue.values. Used for scaling, e.g. in bar graphs or of telemetered raw values.
Normal value range minimum for any of the MeasurementValue.values. Used for scaling, e.g. in bar graphs or of telemetered raw values.
Normal measurement value, e.g., used for percentage calculations.
The ValueAliasSet used for translation of a MeasurementValue.value to a name.
Measurement quality flags for Discrete Values.
Measurement quality flags for Discrete Values.
Reference to the superclass object.
Switch Manual Replace Indicator. Flag indicating that the switch is manual replace.
Removed From Operation Indicator. Flag indicating that the switch is removed from operation.
undocumented
DiscreteValue represents a discrete MeasurementValue.
DiscreteValue represents a discrete MeasurementValue.
Reference to the superclass object.
The value to supervise.
The Control variable associated with the MeasurementValue.
Measurement to which this value is connected.
Response from registered resource acknowleging receipt of dispatch instructions
Response from registered resource acknowleging receipt of dispatch instructions
Reference to the superclass object.
The accepted mw amount by the responder. aka response mw.
The accept status submitted by the responder. enumeration type needs to be defined
The Subject DN is the X509 Certificate Subject DN. This is the essentially the certificate name presented by the client. In the case of ADS Certificates, this will be the user name. It may be from an API Client or the MP Client (GUI).
MW amount associated with instruction. For 5 minute binding dispatches, this is the Goto MW or DOT
The target date/time for the received instruction.
instruction type: commitment out of sequence dispatch
The type of run for the market clearing.
Timestamp indicating the time at which the instruction was received.
start time
undocumented
A containing class that groups all the distribution factors within a market.
A containing class that groups all the distribution factors within a market. This is calculated daily for DA factors and hourly for RT factors.
Reference to the superclass object.
The end of the time interval for which requirement is defined.
The start of the time interval for which requirement is defined.
undocumented
undocumented
undocumented
undocumented
Parent class for different groupings of information collected and managed as a part of a business process.
Parent class for different groupings of information collected and managed as a part of a business process. It will frequently contain references to other objects, such as assets, people and power system resources.
Reference to the superclass object.
Name of the author of this document.
Free text comment.
Date and time that this document was created.
Status of this document. For status of subject matter this document represents (e.g., Agreement, Work), use 'status' attribute.
Electronic address.
Date and time this document was last modified. Documents may potentially be modified many times during their lifetime.
Revision number for this document.
Status of subject matter (e.g., Agreement, Work) this document represents. For status of the document itself, use 'docStatus' attribute.
Document subject.
Document title.
Utility-specific classification of this document, according to its corporate standards, practices, and existing IT systems (e.g., for management of assets, maintenance, work, outage, customers, etc.).
Role an organisation plays with respect to documents.
Role an organisation plays with respect to documents.
Reference to the superclass object.
An area of activity defined within the energy market.
An area of activity defined within the energy market.
Reference to the superclass object.
Provides the necessary information (on a resource basis) to capture the Dispatch Operating Point (DOP) results on a Dispatch interval.
Provides the necessary information (on a resource basis) to capture the Dispatch Operating Point (DOP) results on a Dispatch interval. This information is only relevant to the RT interval market.
Reference to the superclass object.
Dispatched Operating Point (MW)
A value used to establish priority of the DOP when plotting. This is only applicable when two DOPs exist for the same time, but with different MW values. E.g. when indicating a step in the curve. Its used to determine if the curve steps up or down.
Indication of DOP validity. Shows the DOP is calculated from the latest run (YES). A NO indicator shows that the DOP is copied from a previous execution.
DOP time stamp
undocumented
undocumented
undocumented
undocumented
Provides the necessary information (on a resource basis) to capture the Dispatch Operating Target (DOT) results on a Dispatch interval.
Provides the necessary information (on a resource basis) to capture the Dispatch Operating Target (DOT) results on a Dispatch interval. This information is only relevant to the RT interval market.
Reference to the superclass object.
Actual ramp rate.
Flag indicating whether or not the resource was in compliance with the instruction (plus/minus 10%). Directs if a unit is allowed to set the price (ex-post pricing).
Economic Max Limit override for unit, this value is null, if it is not, this value overrides the Energy column value. Allows dispatcher to override the unit's energy value.
Expected energy.
The Degree of Generator Performance (DGP) used for the unit. Measure of how a generator responds to raise /lower signals. Calculated every five minutes.
HASP results.
Hourly Schedule (DA Energy Schedule).
The date/time for the instruction.
True if maximum emergency limit activated; false otherwise. If unit is requested to move up to its max emergency limit., this flag is set to true.
Meter Sub System Load Following.
Desired MW that is not ramp restricted. If no ramp rate limit existed for the unit, this is the MW value tha t the unit was requested to move to.
Non Spin Reserve used to procure energy.
Timestamp when the previous DOT value was issued.
The ramp rate limit for the unit in MWs per minute. Participant bidding data.
Regulation Status (Yes/No).
Spin Reserve used to procure energy.
Standard ramping energy (MWH).
Supplemental Energy procure by Real Time Dispatch.
Output results from the case identifying the reason the unit was committed by the software.
Dispatch operating target value.
undocumented
Drum boiler.
Drum boiler.
Reference to the superclass object.
Rating of drum boiler in steam units.
A duct contains individual wires in the layout as specified with associated wire spacing instances; number of them gives the number of conductors in this duct.
A duct contains individual wires in the layout as specified with associated wire spacing instances; number of them gives the number of conductors in this duct.
Reference to the superclass object.
Number of circuits in duct bank. Refer to associations between a duct (ConductorAsset) and an ACLineSegment to understand which circuits are in which ducts.
Details on amounts due for an account.
Details on amounts due for an account.
Reference to the superclass object.
Part of 'current' that constitutes the arrears portion.
Part of 'current' that constitutes the charge portion: 'charges' = 'Charge.fixedPortion' + 'Charge.variablePortion'.
Current total amount now due: current = principle + arrears + interest + charges. Typically the rule for settlement priority is: interest dues, then arrears dues, then current dues, then charge dues.
Part of 'current' that constitutes the interest portion.
Part of 'current' that constitutes the portion of the principle amount currently due.
A continuously variable component of a control area's MW net interchange schedule.
A continuously variable component of a control area's MW net interchange schedule. Dynamic schedules are sent and received by control areas.
Reference to the superclass object.
Dynamic schedule sign reversal required (true/false)
The "active" or "inactive" status of the dynamic schedule
undocumented
A control area can receive dynamic schedules from other control areas
A control area can send dynamic schedules to other control areas
Abstract parent class for all Dynamics function blocks.
Abstract parent class for all Dynamics function blocks.
Reference to the superclass object.
Function block used indicator. true = use of function block is enabled false = use of function block is disabled.
A conducting equipment used to represent a connection to ground which is typically used to compensate earth faults..
A conducting equipment used to represent a connection to ground which is typically used to compensate earth faults.. An earth fault compensator device modeled with a single terminal implies a second terminal solidly connected to ground. If two terminals are modeled, the ground is not assumed and normal connection rules apply.
Reference to the superclass object.
Nominal resistance of device.
Electronic address information.
Electronic address information.
Reference to the superclass object.
Primary email address.
Alternate email address.
Address on local area network.
MAC (Media Access Control) address.
Password needed to log in.
Radio address.
User ID needed to log in, which can be for an individual person, an organisation, a location, etc.
World wide web address.
Lowest level class in the CIM hierarchy.
Lowest level class in the CIM hierarchy.
All CIM model objects inherit from this class, either directly or indirectly.
Provides overridable functionality to:
Accounts for tracking emissions usage and credits for thermal generating units.
Accounts for tracking emissions usage and credits for thermal generating units. A unit may have zero or more emission accounts, and will typically have one for tracking usage and one for tracking credits.
Reference to the superclass object.
The type of emission, for example sulfur dioxide (SO2). The y1AxisUnits of the curve contains the unit of measure (e.g. kg) and the emissionType is the type of emission (e.g. sulfer dioxide).
The source of the emission value.
A thermal generating unit may have one or more emission allowance accounts.
Relationship between the unit's emission rate in units of mass per hour (Y-axis) and output active power (X-axis) for a given type of emission.
Relationship between the unit's emission rate in units of mass per hour (Y-axis) and output active power (X-axis) for a given type of emission. This curve applies when only one type of fuel is being burned.
Reference to the superclass object.
The emission content per quantity of fuel burned.
The type of emission, which also gives the production rate measurement unit. The y1AxisUnits of the curve contains the unit of measure (e.g. kg) and the emissionType is the type of emission (e.g. sulfer dioxide).
Flag is set to true when output is expressed in net active power.
A thermal generating unit may have one or more emission curves.
Asset container that performs one or more end device functions.
Asset container that performs one or more end device functions. One type of end device is a meter which can perform metering, load management, connect/disconnect, accounting functions, etc. Some end devices, such as ones monitoring and controlling air conditioners, refrigerators, pool pumps may be connected to a meter. All end devices may have communication capability defined by the associated communication function(s). An end device may be owned by a consumer, a service provider, utility or otherwise.
Reference to the superclass object.
Automated meter reading (AMR) or other communication system responsible for communications to this end device.
Installation code.
If true, this is a premises area network (PAN) device.
If true, there is no physical device. As an example, a virtual meter can be defined to aggregate the consumption for two or more physical meters. Otherwise, this is a physical hardware device.
Time zone offset relative to GMT for the location of this end device.
Customer owning this end device.
End device data.
Service location whose service delivery is measured by this end device.
Usage point to which this end device belongs.
Action/command performed by an end device on a device other than the end device.
Action/command performed by an end device on a device other than the end device.
Reference to the superclass object.
Command text.
Amount of time the action of this control is to remain active.
True if the action of this control is indefinite.
Start date and time for action of this control.
End device control issuing this end device action.
Inherent capabilities of an end device (i.e., the functions it supports).
Inherent capabilities of an end device (i.e., the functions it supports).
Reference to the superclass object.
True if autonomous DST (daylight saving time) function is supported.
True if communication function is supported.
True if connect and disconnect function is supported.
True if demand response function is supported.
True if electric metering function is supported.
True if gas metering function is supported.
True if metrology function is supported.
True if on request read function is supported.
True if outage history function is supported.
True if device performs pressure compensation for metered quantities.
True if pricing information is supported.
True if device produces pulse outputs.
True if relays programming function is supported.
True if reverse flow function is supported.
True if device performs super compressibility compensation for metered quantities.
True if device performs temperature compensation for metered quantities.
True if the displaying of text messages is supported.
True if water metering function is supported.
Instructs an end device (or an end device group) to perform a specified action.
Instructs an end device (or an end device group) to perform a specified action.
Reference to the superclass object.
Level of a demand response program request, where 0=emergency. Note: Attribute is not defined on DemandResponseProgram as it is not its inherent property (it serves to control it).
Whether a demand response program request is mandatory. Note: Attribute is not defined on DemandResponseProgram as it is not its inherent property (it serves to control it).
Unique identifier of the business entity originating an end device control.
Identifier assigned by the initiator (e.g. retail electric provider) of an end device control action to uniquely identify the demand response event, text message, or other subject of the control action. Can be used when cancelling an event or text message request or to identify the originating event or text message in a consequential end device event.
(if applicable) Price signal used as parameter for this end device control.
Timing for the control actions performed on the device identified in the end device control.
Reason for the control action that allows to determine how to continue processing. For example, disconnect meter command may require different processing by the receiving system if it has been issued for a network-related reason (protection) or for a payment-related reason.
(if control has scheduled duration) Date and time interval the control has been scheduled to execute within.
Timing for the control actions performed by devices that are responding to event related information sent to the primary device indicated in the end device control. For example, load control actions performed by a PAN device in response to demand response event information sent to a PAN gateway server.
End device action issued by this end device control.
Type of this end device control.
All end devices receiving commands from this end device control.
All usage point groups receiving commands from this end device control.
All usage points receiving commands from this end device control.
Detailed description for a control produced by an end device.
Detailed description for a control produced by an end device. Values in attributes allow for creation of recommended codes to be used for identifying end device controls as follows: <type>.<domain>.<subDomain>.<eventOrAction>.
Reference to the superclass object.
High-level nature of the control.
The most specific part of this control type. It is mainly in the form of a verb that gives action to the control that just occurred.
More specific nature of the control, as a further sub-categorisation of 'domain'.
Type of physical device from which the control was created. A value of zero (0) can be used when the source is unknown.
Event detected by a device function associated with the end device.
Event detected by a device function associated with the end device.
Reference to the superclass object.
Unique identifier of the business entity originating an end device control.
Identifier assigned by the initiator (e.g. retail electric provider) of an end device control action to uniquely identify the demand response event, text message, or other subject of the control action. Can be used when cancelling an event or text message request or to identify the originating event or text message in a consequential end device event.
(if user initiated) ID of user who initiated this end device event.
End device that reported this end device event.
Type of this end device event.
Set of measured values to which this event applies.
Usage point for which this end device event is reported.
Name-value pair, specific to end device events.
Name-value pair, specific to end device events.
Reference to the superclass object.
Name.
Value, including unit information.
End device owning this detail.
Detailed description for an event produced by an end device.
Detailed description for an event produced by an end device. Values in attributes allow for creation of recommended codes to be used for identifying end device events as follows: <type>.<domain>.<subDomain>.<eventOrAction>.
Reference to the superclass object.
High-level nature of the event. By properly classifying events by a small set of domain codes, a system can more easily run reports based on the types of events that have occurred or been received.
The most specific part of this event type. It is mainly in the form of a verb that gives action to the event that just occurred.
More specific nature of the event, as a further sub-categorisation of 'domain'.
Type of physical device from which the event was created. A value of zero (0) can be used when the source is unknown.
Function performed by an end device such as a meter, communication equipment, controllers, etc.
Function performed by an end device such as a meter, communication equipment, controllers, etc.
Reference to the superclass object.
True if the function is enabled.
End device that performs this function.
Abstraction for management of group communications within a two-way AMR system or the data for a group of related end devices.
Abstraction for management of group communications within a two-way AMR system or the data for a group of related end devices. Commands can be issued to all of the end devices that belong to the group using a defined group address and the underlying AMR communication infrastructure.
Reference to the superclass object.
Type of this group.
All end device controls sending commands to this end device group.
All end devices this end device group refers to.
End device data.
End device data.
Reference to the superclass object.
Inherent capabilities of the device (i.e., the functions it supports).
If true, this is a solid state end device (as opposed to a mechanical or electromechanical device).
Number of potential phases the end device supports, typically 0, 1 or 3.
Rated current.
Rated voltage.
Timing for the control actions of end devices.
Timing for the control actions of end devices.
Reference to the superclass object.
Duration of the end device control action or the business event that is the subject of the end device control.
True if 'duration' is indefinite.
Start and end time of an interval during which end device control actions are to be executed.
Kind of randomisation to be applied to the end device control actions to be executed.
Describes an area having energy production or consumption.
Describes an area having energy production or consumption. Specializations are intended to support the load allocation function as typically required in energy management systems or planning studies to allocate hypothesized load levels to individual load points for power flow analysis. Often the energy area can be linked to both measured and forecast load levels.
Reference to the superclass object.
The control area specification that is used for the load forecast.
Generic user of energy - a point of consumption on the power system model.
Generic user of energy - a point of consumption on the power system model.
Reference to the superclass object.
Number of individual customers represented by this demand.
Used for Yn and Zn connections. True if the neutral is solidly grounded.
Active power of the load. Load sign convention is used, i.e. positive sign means flow out from a node.
Active power of the load that is a fixed quantity. Load sign convention is used, i.e. positive sign means flow out from a node.
Fixed active power as per cent of load group fixed active power. Load sign convention is used, i.e. positive sign means flow out from a node.
The type of phase connection, such as wye or delta.
Reactive power of the load. Load sign convention is used, i.e. positive sign means flow out from a node.
Reactive power of the load that is a fixed quantity. Load sign convention is used, i.e. positive sign means flow out from a node.
Fixed reactive power as per cent of load group fixed reactive power. Load sign convention is used, i.e. positive sign means flow out from a node.
Load dynamics model used to describe dynamic behavior of this energy consumer.
The load response characteristic of this load. If missing, this load is assumed to be constant power.
The energy consumer is assigned to this power cut zone.
Optimal Power Flow or State Estimator Load Data for OTS.
Optimal Power Flow or State Estimator Load Data for OTS. This is used for RealTime, Study and Maintenance Users
Reference to the superclass object.
The MVAR load Attribute Usage: The reactive power consumption of the load in MW
The active power consumption of the load in MW
undocumented
A single phase of an energy consumer.
A single phase of an energy consumer.
Reference to the superclass object.
Active power of the load that is a fixed quantity. Load sign convention is used, i.e. positive sign means flow out from a node.
Fixed active power as per cent of load group fixed active power. Load sign convention is used, i.e. positive sign means flow out from a node.
Phase of this energy consumer component. If the energy consumer is wye connected, the connection is from the indicated phase to the central ground or neutral point. If the energy consumer is delta connected, the phase indicates an energy consumer connected from the indicated phase to the next logical non-neutral phase.
Reactive power of the load that is a fixed quantity. Load sign convention is used, i.e. positive sign means flow out from a node.
Fixed reactive power as per cent of load group fixed reactive power. Load sign convention is used, i.e. positive sign means flow out from a node.
The energy consumer to which this phase belongs.
Energy and Ancillary Market (e.g.
Energy and Ancillary Market (e.g. Energy, Spinning Reserve, Non-Spinning Reserve) with a description of the Market operation control parameters.
Reference to the superclass object.
undocumented
undocumented
undocumented
Relationship between a price in $(or other monetary unit) /hour (Y-axis) and a MW value (X-axis).
Relationship between a price in $(or other monetary unit) /hour (Y-axis) and a MW value (X-axis).
Reference to the superclass object.
An Energy Price Index for each Resource is valid for a period (e.g.
An Energy Price Index for each Resource is valid for a period (e.g. daily) that is identified by a Valid Period Start Time and a Valid Period End Time. An Energy Price Index is in $/MWh.
Reference to the superclass object.
End effective date
Energy price index
EPI type such as wholesale or retail
Time updated
Start effective date
undocumented
An EnergyProduct is offered commercially as a ContractOrTariff.
An EnergyProduct is offered commercially as a ContractOrTariff.
Reference to the superclass object.
undocumented
A Marketer may resell an EnergyProduct.
A Marketer holds title to an EnergyProduct.
Specifies the start time, stop time, level for an EnergyTransaction.
Specifies the start time, stop time, level for an EnergyTransaction.
Reference to the superclass object.
An EnergyTransaction shall have at least one EnergyProfile.
undocumented
Used to define the type of generation for scheduling purposes.
Used to define the type of generation for scheduling purposes.
Reference to the superclass object.
A generic equivalent for an energy supplier on a transmission or distribution voltage level.
A generic equivalent for an energy supplier on a transmission or distribution voltage level.
Reference to the superclass object.
High voltage source active injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Phase-to-phase nominal voltage.
Positive sequence Thevenin resistance.
Zero sequence Thevenin resistance.
High voltage source reactive injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Negative sequence Thevenin resistance.
Phase angle of a-phase open circuit.
Phase-to-phase open circuit voltage magnitude.
Positive sequence Thevenin reactance.
Zero sequence Thevenin reactance.
Negative sequence Thevenin reactance.
Energy Scheduling Type of an Energy Source
Action taken with this energy source.
Wind generator Type 3 or 4 dynamics model associated with this energy source.
Action on energy source as a switching step.
Action on energy source as a switching step.
Reference to the superclass object.
Switching action to perform.
Energy source on which this action is taken.
Group to which this step belongs.
Specifies the schedule for energy transfers between interchange areas that are necessary to satisfy the associated interchange transaction.
Specifies the schedule for energy transfers between interchange areas that are necessary to satisfy the associated interchange transaction.
Reference to the superclass object.
Interchange capacity flag. When the flag is set to true, it indicates a transaction is capacity backed.
Maximum congestion charges in monetary units.
Delivery point active power.
Transaction minimum active power if dispatchable.
Firm interchange flag indicates whether or not this energy transaction can be changed without potential financial consequences.
Willing to Pay congestion flag
Reason for energy transaction.
Receipt point active power.
{ Approve | Deny | Study }
undocumented
The "Source" for an EnergyTransaction is an EnergyProduct which is injected into a ControlArea. Typically this is a ServicePoint.
Energy is transferred between interchange areas
Energy is transferred between interchange areas
undocumented
This is a environmental based limit dependency model for calculating operational limits.
This is a environmental based limit dependency model for calculating operational limits.
Reference to the superclass object.
The parts of a power system that are physical devices, electronic or mechanical.
The parts of a power system that are physical devices, electronic or mechanical.
Reference to the superclass object.
The single instance of equipment represents multiple pieces of equipment that have been modeled together as an aggregate. Examples would be power transformers or synchronous machines operating in parallel modeled as a single aggregate power transformer or aggregate synchronous machine. This is not to be used to indicate equipment that is part of a group of interdependent equipment produced by a network production program.
If true, the equipment is normally in service.
Container of this equipment.
undocumented
A modeling construct to provide a root class for containing equipment.
A modeling construct to provide a root class for containing equipment.
Reference to the superclass object.
A fault applied at the terminal, external to the equipment.
A fault applied at the terminal, external to the equipment. This class is not used to specify faults internal to the equipment.
Reference to the superclass object.
The terminal connecting to the bus to which the fault is applied.
This represents one instance of an equipment that contributes to the calculation of an operational limit.
This represents one instance of an equipment that contributes to the calculation of an operational limit.
Reference to the superclass object.
Equipment contributing toward the series limit. The reference here is to Equipment rather than a specific limit on the equipment so the grouiping can be reused for multiple limits of different types on the same instance of equipment.
Calculation in which the refernce to equipment applies.
The class represents equivalent branches.
The class represents equivalent branches.
Reference to the superclass object.
Negative sequence series resistance from terminal sequence 1 to terminal sequence 2. Used for short circuit data exchange according to IEC 60909
Negative sequence series resistance from terminal sequence 2 to terminal sequence 1. Used for short circuit data exchange according to IEC 60909
Negative sequence series reactance from terminal sequence 1 to terminal sequence 2. Used for short circuit data exchange according to IEC 60909
Negative sequence series reactance from terminal sequence 2 to terminal sequence 1. Used for short circuit data exchange according to IEC 60909.
Positive sequence series resistance from terminal sequence 1 to terminal sequence 2 . Used for short circuit data exchange according to IEC 60909.
Positive sequence series resistance from terminal sequence 2 to terminal sequence 1. Used for short circuit data exchange according to IEC 60909
Positive sequence series reactance from terminal sequence 1 to terminal sequence 2. Used for short circuit data exchange according to IEC 60909
Positive sequence series reactance from terminal sequence 2 to terminal sequence 1. Used for short circuit data exchange according to IEC 60909
Positive sequence series resistance of the reduced branch.
Resistance from terminal sequence 2 to terminal sequence 1 . Used for steady state power flow. This attribute is optional and represent unbalanced network such as off-nominal phase shifter. If only EquivalentBranch.r is given, then EquivalentBranch.r21 is assumed equal to EquivalentBranch.r.
Positive sequence series reactance of the reduced branch.
Reactance from terminal sequence 2 to terminal sequence 1 . Used for steady state power flow. This attribute is optional and represent unbalanced network such as off-nominal phase shifter. If only EquivalentBranch.x is given, then EquivalentBranch.x21 is assumed equal to EquivalentBranch.x.
Zero sequence series resistance from terminal sequence 1 to terminal sequence 2. Used for short circuit data exchange according to IEC 60909
Zero sequence series resistance from terminal sequence 2 to terminal sequence 1. Used for short circuit data exchange according to IEC 60909
Zero sequence series reactance from terminal sequence 1 to terminal sequence 2. Used for short circuit data exchange according to IEC 60909
Zero sequence series reactance from terminal sequence 2 to terminal sequence 1. Used for short circuit data exchange according to IEC 60909
The class represents equivalent objects that are the result of a network reduction.
The class represents equivalent objects that are the result of a network reduction. The class is the base for equivalent objects of different types.
Reference to the superclass object.
The equivalent where the reduced model belongs.
This class represents equivalent injections (generation or load).
This class represents equivalent injections (generation or load). Voltage regulation is allowed only at the point of connection.
Reference to the superclass object.
Maximum active power of the injection.
Used for modeling of infeed for load flow exchange. Not used for short circuit modeling. If maxQ and minQ are not used ReactiveCapabilityCurve can be used.
Minimum active power of the injection.
Used for modeling of infeed for load flow exchange. Not used for short circuit modeling. If maxQ and minQ are not used ReactiveCapabilityCurve can be used.
Equivalent active power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Equivalent reactive power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Positive sequence resistance. Used to represent Extended-Ward (IEC 60909).
Zero sequence resistance. Used to represent Extended-Ward (IEC 60909).
Negative sequence resistance. Used to represent Extended-Ward (IEC 60909).
Specifies whether or not the EquivalentInjection has the capability to regulate the local voltage.
Specifies the default regulation status of the EquivalentInjection. True is regulating. False is not regulating.
The target voltage for voltage regulation.
Positive sequence reactance. Used to represent Extended-Ward (IEC 60909).
Zero sequence reactance. Used to represent Extended-Ward (IEC 60909).
Negative sequence reactance. Used to represent Extended-Ward (IEC 60909).
The reactive capability curve used by this equivalent injection.
A class that represents an external meshed network that has been reduced to an electrically equivalent model.
A class that represents an external meshed network that has been reduced to an electrically equivalent model. The ConnectivityNodes contained in the equivalent are intended to reflect internal nodes of the equivalent. The boundary Connectivity nodes where the equivalent connects outside itself are NOT contained by the equivalent.
Reference to the superclass object.
The class represents equivalent shunts.
The class represents equivalent shunts.
Reference to the superclass object.
Positive sequence shunt susceptance.
Positive sequence shunt conductance.
Information that generally describes the Bill of Material Structure and its contents for a utility.
Information that generally describes the Bill of Material Structure and its contents for a utility. This is used by ERP systems to transfer Bill of Material information between two business applications.
Reference to the superclass object.
undocumented
Relationship under a particular name, usually evidenced by a deposit against which withdrawals can be made.
Relationship under a particular name, usually evidenced by a deposit against which withdrawals can be made. Types of bank accounts include: demand, time, custodial, joint, trustee, corporate, special, and regular accounts.
Reference to the superclass object.
Bank ABA.
An individual item on a bill of materials.
An individual item on a bill of materials.
Reference to the superclass object.
undocumented
undocumented
undocumented
Accounting structure of a business.
Accounting structure of a business. Each account represents a financial aspect of a business, such as its Accounts Payable, or the value of its inventory, or its office supply expenses.
Reference to the superclass object.
Information that describes aptitudes of a utility employee.
Information that describes aptitudes of a utility employee. Unlike Skills that an ErpPerson must be certified to perform before undertaking certain type of assignments (to be able to perfrom a Craft), ErpCompetency has more to do with typical Human Resource (HR) matters such as schooling, training, etc.
Reference to the superclass object.
Shadow class for Document, to isolate subclassing from this package.
Shadow class for Document, to isolate subclassing from this package. If any subclass gets normative and needs inheritance, it will inherit directly from Document.
Reference to the superclass object.
General Utility Engineering Change Order information.
General Utility Engineering Change Order information.
Reference to the superclass object.
Shadow class for IdentifiedObject, to isolate subclassing from this package.
Shadow class for IdentifiedObject, to isolate subclassing from this package. If any subclass gets normative and needs inheritance, it will inherit directly from IdentifiedObject.
Reference to the superclass object.
Utility inventory-related information about an item or part (and not for description of the item and its attributes).
Utility inventory-related information about an item or part (and not for description of the item and its attributes). It is used by ERP applications to enable the synchronization of Inventory data that exists on separate Item Master databases. This data is not the master data that describes the attributes of the item such as dimensions, weight, or unit of measure - it describes the item as it exists at a specific location.
Reference to the superclass object.
undocumented
undocumented
This is related to Inventory physical counts organized by AssetModel.
This is related to Inventory physical counts organized by AssetModel. Note that a count of a type of asset can be accomplished by the association inherited by AssetModel (from Document) to Asset.
Reference to the superclass object.
undocumented
undocumented
A roll up of invoice line items.
A roll up of invoice line items. The whole invoice has a due date and amount to be paid, with information such as customer, banks etc. being obtained through associations. The invoice roll up is based on individual line items that each contain amounts and descriptions for specific services or products.
Reference to the superclass object.
Total amount due on this invoice based on line items and applicable adjustments.
Kind of media by which the CustomerBillingInfo was delivered.
Calculated date upon which the Invoice amount is due.
Kind of invoice (default is 'sales').
Date on which the customer billing statement/invoice was printed/mailed.
True if payment is to be paid by a Customer to accept a particular ErpQuote (with associated Design) and have work initiated, at which time an associated ErpInvoice should automatically be generated. EprPayment.subjectStatus satisfies terms specificed in the ErpQuote.
Number of an invoice to be reference by this invoice.
Date and time when the invoice is issued.
Type of invoice transfer.
undocumented
An individual line item on an invoice.
An individual line item on an invoice.
Reference to the superclass object.
Bill period for the line item.
General Ledger account code, must be a valid combination.
Date and time line item will be posted to the General Ledger.
Kind of line item.
Amount due for this line item.
Line item number on invoice statement.
Version number of the bill run.
Net line item charge amount.
Previous line item charge amount.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
Can be used to request an application to process an issue or request information about an issue.
Can be used to request an application to process an issue or request information about an issue.
Reference to the superclass object.
undocumented
undocumented
undocumented
Any unique purchased part for manufactured product tracked by ERP systems for a utility.
Any unique purchased part for manufactured product tracked by ERP systems for a utility. Item, as used by the OAG, refers to the basic information about an item, including its attributes, cost, and locations. It does not include item quantities. Compare to the Inventory, which includes all quantities and other location-specific information.
Reference to the superclass object.
undocumented
undocumented
Book for recording accounting transactions as they occur.
Book for recording accounting transactions as they occur. Transactions and adjustments are first recorded in a journal, which is like a diary of instructions, advising which account to be charged and by how much.
Reference to the superclass object.
Details of an individual entry in a journal, which is to be posted to a ledger on the posting date.
Details of an individual entry in a journal, which is to be posted to a ledger on the posting date.
Reference to the superclass object.
Account identifier for this entry.
The amount of the debit or credit for this account.
Date and time this entry is to be posted to the ledger.
The identifer of the source for this entry.
undocumented
Date and time journal entry was recorded.
undocumented
undocumented
undocumented
Individual entry of a given Ledger Budget, typically containing information such as amount, accounting date, accounting period, and is associated with the applicable general ledger account.
Individual entry of a given Ledger Budget, typically containing information such as amount, accounting date, accounting period, and is associated with the applicable general ledger account.
Reference to the superclass object.
undocumented
undocumented
undocumented
In accounting transactions, a ledger is a book containing accounts to which debits and credits are posted from journals, where transactions are initially recorded.
In accounting transactions, a ledger is a book containing accounts to which debits and credits are posted from journals, where transactions are initially recorded. Journal entries are periodically posted to the ledger. Ledger Actual represents actual amounts by account within ledger within company or business area. Actual amounts may be generated in a source application and then loaded to a specific ledger within the enterprise general ledger or budget application.
Reference to the superclass object.
Information for utility Ledger Budgets.
Information for utility Ledger Budgets. They support the transfer budget amounts between all possible source applications throughout an enterprise and a general ledger or budget application.
Reference to the superclass object.
Details of an individual entry in a ledger, which was posted from a journal on the posted date.
Details of an individual entry in a ledger, which was posted from a journal on the posted date.
Reference to the superclass object.
Account identifier for this entry.
Kind of account for this entry.
The amount of the debit or credit for this account.
Date and time this entry was posted to the ledger.
undocumented
Date and time journal entry was recorded.
undocumented
undocumented
undocumented
undocumented
Of an ErpPurchaseOrder, this is an individually ordered item or product along with the quantity, price and other descriptive information.
Of an ErpPurchaseOrder, this is an individually ordered item or product along with the quantity, price and other descriptive information.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
A transaction that represents an invoice from a supplier.
A transaction that represents an invoice from a supplier. A payable (or voucher) is an open item, approved and ready for payment, in the Accounts Payable ledger.
Reference to the superclass object.
Of an ErpPayable, a line item references an ErpInvoiceLineitem or other source such as credit memos.
Of an ErpPayable, a line item references an ErpInvoiceLineitem or other source such as credit memos.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
Payment infromation and status for any individual line item of an ErpInvoice (e.g., when payment is from a customer).
Payment infromation and status for any individual line item of an ErpInvoice (e.g., when payment is from a customer). ErpPayable is also updated when payment is to a supplier and ErpReceivable is updated when payment is from a customer. Multiple payments can be made against a single line item and an individual payment can apply to more that one line item.
Reference to the superclass object.
Payment terms (e.g., net 30).
Information that applies to the basic data about a utility person, used by ERP applications to transfer Personnel data for a worker.
Information that applies to the basic data about a utility person, used by ERP applications to transfer Personnel data for a worker.
Reference to the superclass object.
undocumented
Utility Project Accounting information, used by ERP applications to enable all relevant sub-systems that submit single sided transactions to transfer information with a Project Accounting Application.
Utility Project Accounting information, used by ERP applications to enable all relevant sub-systems that submit single sided transactions to transfer information with a Project Accounting Application. This would include, but not necessarily be limited to: Accounts Payable, Accounts Receivable, Budget, Order Management, Purchasing, Time and Labor, Travel and Expense.
Reference to the superclass object.
A document that communicates an order to purchase goods from a buyer to a supplier.
A document that communicates an order to purchase goods from a buyer to a supplier. The PurchaseOrder carries information to and from the buyer and supplier. It is a legally binding document once both Parties agree to the contents and the specified terms and conditions of the order.
Reference to the superclass object.
Document describing the prices of goods or services provided by a supplier.
Document describing the prices of goods or services provided by a supplier. It includes the terms of the purchase, delivery proposals, identification of goods or services ordered, as well as their quantities.
Reference to the superclass object.
Of an ErpQuote, the item or product quoted along with quantity, price and other descriptive information.
Of an ErpQuote, the item or product quoted along with quantity, price and other descriptive information.
Reference to the superclass object.
undocumented
undocumented
undocumented
Some utilities provide quotes to customer for services, where the customer accepts the quote by making a payment. An invoice is required for this to occur.
undocumented
undocumented
Of an ErpReceiveDelivery, this is an individually received good or service by the Organisation receiving goods or services.
Of an ErpReceiveDelivery, this is an individually received good or service by the Organisation receiving goods or services. It may be used to indicate receipt of goods in conjunction with a purchase order line item.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
Individual entry of an ErpReceivable, it is a particular transaction representing an invoice, credit memo or debit memo to a customer.
Individual entry of an ErpReceivable, it is a particular transaction representing an invoice, credit memo or debit memo to a customer.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
Transaction representing an invoice, credit memo or debit memo to a customer.
Transaction representing an invoice, credit memo or debit memo to a customer. It is an open (unpaid) item in the Accounts Receivable ledger.
Reference to the superclass object.
Transaction for an Organisation receiving goods or services that may be used to indicate receipt of goods in conjunction with a purchase order.
Transaction for an Organisation receiving goods or services that may be used to indicate receipt of goods in conjunction with a purchase order. A receivable is an open (unpaid) item in the Accounts Receivable ledger.
Reference to the superclass object.
Information that describes a requested item and its attributes.
Information that describes a requested item and its attributes.
Reference to the superclass object.
undocumented
Cost of material.
undocumented
Quantity of item requisitioned.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
General information that applies to a utility requisition that is a request for the purchase of goods or services.
General information that applies to a utility requisition that is a request for the purchase of goods or services. Typically, a requisition leads to the creation of a purchase order to a specific supplier.
Reference to the superclass object.
General purpose Sales Order is used for utility service orders, etc.
General purpose Sales Order is used for utility service orders, etc. As used by the OAG, the SalesOrder is a step beyond a PurchaseOrder in that the receiving entity of the order also communicates SalesInformoration about the Order along with the Order itself.
Reference to the superclass object.
For a utility, general information that describes physical locations of organizations or the location codes and their meanings.
For a utility, general information that describes physical locations of organizations or the location codes and their meanings. This enables ERP applications to ensure that the physical location identifiers are synchronized between the business applications.
Reference to the superclass object.
undocumented
undocumented
An individual entry on an ErpTimeSheet.
An individual entry on an ErpTimeSheet.
Reference to the superclass object.
undocumented
undocumented
undocumented
Time sheet for employees and contractors.
Time sheet for employees and contractors. Note that ErpTimeSheet inherits the relationship to ErpPerson from Document.
Reference to the superclass object.
Model of ex-post calcultion of MW losses.
Model of ex-post calcultion of MW losses.
Reference to the superclass object.
Model results of ex-post calculation of MW losses.
Model results of ex-post calculation of MW losses. Summarizes loss in two categories losses on the the extra high voltage transmission and total losses. Calculated for each subcontrol area.
Reference to the superclass object.
EHV MW losses in the company Attribute Usage: Information purposes - Output of LPA engine.
Total MW losses in the company Attribute Usage: Information purposes - Output of LPA engine.
undocumented
undocumented
Model of ex-post calculation of cleared MW on a regional basis
Model of ex-post calculation of cleared MW on a regional basis
Reference to the superclass object.
undocumented
Model of expost calculation of cleared MW on a region basis.
Model of expost calculation of cleared MW on a region basis. Includes cleared price
Reference to the superclass object.
undocumented
undocumented
undocumented
Model of ex-post pricing of nodes
Model of ex-post pricing of nodes
Reference to the superclass object.
market energy price
Model of ex-post pricing of nodes.
Model of ex-post pricing of nodes. Includes LMP information, pnode based.
Reference to the superclass object.
Congestion component of Location Marginal Price (LMP) in monetary units per MW; congestion component of the hourly LMP at a specific pricing node Attribute Usage: Result of the Security, Pricing, and Dispatch(SPD)/Simultaneous Feasibility Test(SFT) software and denotes the hourly congestion component of LMP for each pricing node.
5 min weighted average LMP; the Location Marginal Price of the Pnode for which price calculation is carried out. Attribute Usage: 5 min weighted average LMP to be displayed on UI
Loss component of Location Marginal Price (LMP) in monetary units per MW; loss component of the hourly LMP at a specific pricing node Attribute Usage: Result of the Security, Pricing, and Dispatch(SPD)/Simultaneous Feasibility Test(SFT) software and denotes the hourly loss component of LMP for each pricing node.
undocumented
undocumented
Model of ex-post pricing of resources.
Model of ex-post pricing of resources.
Reference to the superclass object.
Model of ex-post pricing of resources contains components of LMPs: energy, congestion, loss.
Model of ex-post pricing of resources contains components of LMPs: energy, congestion, loss. Resource based.
Reference to the superclass object.
LMP component in USD (deprecated)
Desired output of unit
Unit Dispatch rate from real time unit dispatch.
LMP (Local Marginal Price) in USD at the equipment (deprecated)
loss lmp (deprecated)
Economic Maximum MW
Economic Minimum MW
Current MW output of the equipment Attribute Usage: Information purposes - Information purposes - Output of LPA engine.
Status of equipment
undocumented
undocumented
Modified IEEE AC1A alternator-supplied rectifier excitation system with different rate feedback source.
Modified IEEE AC1A alternator-supplied rectifier excitation system with different rate feedback source.
Reference to the superclass object.
Indicates if both HV gate and LV gate are active (HVLVgates). true = gates are used false = gates are not used. Typical Value = true.
Voltage regulator gain (Ka). Typical Value = 400.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.2.
Demagnetizing factor, a function of exciter alternator reactances (Kd). Typical Value = 0.38.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Excitation control system stabilizer gains (Kf). Typical Value = 0.03.
Coefficient to allow different usage of the model (Kf1). Typical Value = 0.
Coefficient to allow different usage of the model (Kf2). Typical Value = 1.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Ve1, back of commutating reactance (Se[Ve1]). Typical Value = 0.1.
Exciter saturation function value at the corresponding exciter voltage, Ve2, back of commutating reactance (Se[Ve2]). Typical Value = 0.03.
Voltage regulator time constant (Ta). Typical Value = 0.02.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 0.8.
Excitation control system stabilizer time constant (Tf). Typical Value = 1.
Maximum voltage regulator output (Vamax). Typical Value = 14.5.
Minimum voltage regulator output (Vamin). Typical Value = -14.5.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve1). Typical Value = 4.18.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve2). Typical Value = 3.14.
Maximum voltage regulator outputs (Vrmax). Typical Value = 6.03.
Minimum voltage regulator outputs (Rrmin). Typical Value = -5.43.
Modified IEEE AC2A alternator-supplied rectifier excitation system with different field current limit.
Modified IEEE AC2A alternator-supplied rectifier excitation system with different field current limit.
Reference to the superclass object.
Indicates if HV gate is active (HVgate). true = gate is used false = gate is not used. Typical Value = true.
Voltage regulator gain (Ka). Typical Value = 400.
Second stage regulator gain (Kb) (>0). Exciter field current controller gain. Typical Value = 25.
Second stage regulator gain (Kb1). It is exciter field current controller gain used as alternative to Kb to represent a variant of the ExcAC2A model. Typical Value = 25.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.28.
Demagnetizing factor, a function of exciter alternator reactances (Kd). Typical Value = 0.35.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Excitation control system stabilizer gains (Kf). Typical Value = 0.03.
Exciter field current feedback gain (Kh). Typical Value = 1.
Exciter field current limiter gain (Kl). Typical Value = 10.
Coefficient to allow different usage of the model (Kl1). Typical Value = 1.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Indicates if LV gate is active (LVgate). true = gate is used false = gate is not used. Typical Value = true.
Exciter saturation function value at the corresponding exciter voltage, Ve1, back of commutating reactance (Se[Ve1]). Typical Value = 0.037.
Exciter saturation function value at the corresponding exciter voltage, Ve2, back of commutating reactance (Se[Ve2]). Typical Value = 0.012.
Voltage regulator time constant (Ta). Typical Value = 0.02.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 0.6.
Excitation control system stabilizer time constant (Tf). Typical Value = 1.
Maximum voltage regulator output (Vamax). Typical Value = 8.
Minimum voltage regulator output (Vamin). Typical Value = -8.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve1). Typical Value = 4.4.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve2). Typical Value = 3.3.
Exciter field current limit reference (Vfemax). Typical Value = 4.4.
Maximum exciter field current (Vlr). Typical Value = 4.4.
Maximum voltage regulator outputs (Vrmax). Typical Value = 105.
Minimum voltage regulator outputs (Vrmin). Typical Value = -95.
Modified IEEE AC3A alternator-supplied rectifier excitation system with different field current limit.
Modified IEEE AC3A alternator-supplied rectifier excitation system with different field current limit.
Reference to the superclass object.
Value of EFD at which feedback gain changes (Efdn). Typical Value = 2.36.
Voltage regulator gain (Ka). Typical Value = 45.62.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.104.
Demagnetizing factor, a function of exciter alternator reactances (Kd). Typical Value = 0.499.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Excitation control system stabilizer gains (Kf). Typical Value = 0.143.
Coefficient to allow different usage of the model (Kf1). Typical Value = 1.
Coefficient to allow different usage of the model (Kf2). Typical Value = 0.
Gain used in the minimum field voltage limiter loop (Klv). Typical Value = 0.194.
Excitation control system stabilizer gain (Kn). Typical Value =0.05.
Constant associated with regulator and alternator field power supply (Kr). Typical Value =3.77.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Ve1, back of commutating reactance (Se[Ve1]). Typical Value = 1.143.
Exciter saturation function value at the corresponding exciter voltage, Ve2, back of commutating reactance (Se[Ve2]). Typical Value = 0.1.
Voltage regulator time constant (Ta). Typical Value = 0.013.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 1.17.
Excitation control system stabilizer time constant (Tf). Typical Value = 1.
Maximum voltage regulator output (Vamax). Typical Value = 1.
Minimum voltage regulator output (Vamin). Typical Value = -0.95.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve1) equals Vemax (Ve1). Typical Value = 6.24.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve2). Typical Value = 4.68.
Minimum exciter voltage output (Vemin). Typical Value = 0.1.
Exciter field current limit reference (Vfemax). Typical Value = 16.
Field voltage used in the minimum field voltage limiter loop (Vlv). Typical Value = 0.79.
Modified IEEE AC4A alternator-supplied rectifier excitation system with different minimum controller output.
Modified IEEE AC4A alternator-supplied rectifier excitation system with different minimum controller output.
Reference to the superclass object.
Voltage regulator gain (Ka). Typical Value = 200.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.
Voltage regulator time constant (Ta). Typical Value = 0.015.
Voltage regulator time constant (Tb). Typical Value = 10.
Voltage regulator time constant (Tc). Typical Value = 1.
Maximum voltage regulator input limit (Vimax). Typical Value = 10.
Minimum voltage regulator input limit (Vimin). Typical Value = -10.
Maximum voltage regulator output (Vrmax). Typical Value = 5.64.
Minimum voltage regulator output (Vrmin). Typical Value = -4.53.
Modified IEEE AC5A alternator-supplied rectifier excitation system with different minimum controller output.
Modified IEEE AC5A alternator-supplied rectifier excitation system with different minimum controller output.
Reference to the superclass object.
Coefficient to allow different usage of the model (a). Typical Value = 1.
Exciter voltage at which exciter saturation is defined (Efd1). Typical Value = 5.6.
Exciter voltage at which exciter saturation is defined (Efd2). Typical Value = 4.2.
Voltage regulator gain (Ka). Typical Value = 400.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Excitation control system stabilizer gains (Kf). Typical Value = 0.03.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Efd1 (SE[Efd1]). Typical Value = 0.86.
Exciter saturation function value at the corresponding exciter voltage, Efd2 (SE[Efd2]). Typical Value = 0.5.
Voltage regulator time constant (Ta). Typical Value = 0.02.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 0.8.
Excitation control system stabilizer time constant (Tf1). Typical Value = 1.
Excitation control system stabilizer time constant (Tf2). Typical Value = 0.8.
Excitation control system stabilizer time constant (Tf3). Typical Value = 0.
Maximum voltage regulator output (Vrmax). Typical Value = 7.3.
Minimum voltage regulator output (Vrmin). Typical Value =-7.3.
Modified IEEE AC6A alternator-supplied rectifier excitation system with speed input.
Modified IEEE AC6A alternator-supplied rectifier excitation system with speed input.
Reference to the superclass object.
Voltage regulator gain (Ka). Typical Value = 536.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.173.
Demagnetizing factor, a function of exciter alternator reactances (Kd). Typical Value = 1.91.
Exciter constant related to self-excited field (Ke). Typical Value = 1.6.
Exciter field current limiter gain (Kh). Typical Value = 92.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Ve1, back of commutating reactance (Se[Ve1]). Typical Value = 0.214.
Exciter saturation function value at the corresponding exciter voltage, Ve2, back of commutating reactance (Se[Ve2]). Typical Value = 0.044.
Voltage regulator time constant (Ta). Typical Value = 0.086.
Voltage regulator time constant (Tb). Typical Value = 9.
Voltage regulator time constant (Tc). Typical Value = 3.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 1.
Exciter field current limiter time constant (Th). Typical Value = 0.08.
Exciter field current limiter time constant (Tj). Typical Value = 0.02.
Voltage regulator time constant (Tk). Typical Value = 0.18.
Maximum voltage regulator output (Vamax). Typical Value = 75.
Minimum voltage regulator output (Vamin). Typical Value = -75.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve1). Typical Value = 7.4.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve2). Typical Value = 5.55.
Exciter field current limit reference (Vfelim). Typical Value = 19.
Maximum field current limiter signal reference (Vhmax). Typical Value = 75.
Maximum voltage regulator output (Vrmax). Typical Value = 44.
Minimum voltage regulator output (Vrmin). Typical Value = -36.
Modified IEEE AC8B alternator-supplied rectifier excitation system with speed input and input limiter.
Modified IEEE AC8B alternator-supplied rectifier excitation system with speed input and input limiter.
Reference to the superclass object.
Input limiter indicator. true = input limiter Vimax and Vimin is considered false = input limiter Vimax and Vimin is not considered. Typical Value = true.
Voltage regulator gain (Ka). Typical Value = 1.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.55.
Demagnetizing factor, a function of exciter alternator reactances (Kd). Typical Value = 1.1.
Voltage regulator derivative gain (Kdr). Typical Value = 10.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Voltage regulator integral gain (Kir). Typical Value = 5.
Voltage regulator proportional gain (Kpr). Typical Value = 80.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
PID limiter indicator. true = input limiter Vpidmax and Vpidmin is considered false = input limiter Vpidmax and Vpidmin is not considered. Typical Value = true.
Exciter saturation function value at the corresponding exciter voltage, Ve1, back of commutating reactance (Se[Ve1]). Typical Value = 0.3.
Exciter saturation function value at the corresponding exciter voltage, Ve2, back of commutating reactance (Se[Ve2]). Typical Value = 3.
Voltage regulator time constant (Ta). Typical Value = 0.
Lag time constant (Tdr). Typical Value = 0.1.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 1.2.
Selector for the limiter on the block [1/sTe]. See diagram for meaning of true and false.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve1) equals VEMAX (Ve1). Typical Value = 6.5.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve2). Typical Value = 9.
Minimum exciter voltage output (Vemin). Typical Value = 0.
Exciter field current limit reference (Vfemax). Typical Value = 6.
Input signal maximum (Vimax). Typical Value = 35.
Input signal minimum (Vimin). Typical Value = -10.
PID maximum controller output (Vpidmax). Typical Value = 35.
PID minimum controller output (Vpidmin). Typical Value = -10.
Maximum voltage regulator output (Vrmax). Typical Value = 35.
Minimum voltage regulator output (Vrmin). Typical Value = 0.
Multiply by generator's terminal voltage indicator. true =the limits Vrmax and Vrmin are multiplied by the generator�s terminal voltage to represent a thyristor power stage fed from the generator terminals false = limits are not multiplied by generator's terminal voltage. Typical Value = false.
Italian excitation system.
Italian excitation system. It represents static field voltage or excitation current feedback excitation system.
Reference to the superclass object.
Governor Control Flag (BLINT). 0 = lead-lag regulator 1 = proportional integral regulator. Typical Value = 0.
Minimum exciter current (IFMN). Typical Value = -5.2.
Maximum exciter current (IFMX). Typical Value = 6.5.
Exciter gain (K2). Typical Value = 20.
AVR gain (K3). Typical Value = 1000.
Ceiling factor (KCE). Typical Value = 1.
Feedback enabling (KRVECC). 0 = Open loop control 1 = Closed loop control. Typical Value = 1.
Rate feedback signal flag (KVFIF). 0 = output voltage of the exciter 1 = exciter field current. Typical Value = 0.
Time constant (T1). Typical Value = 20.
Time constant (T2). Typical Value = 0.05.
Time constant (T3). Typical Value = 1.6.
Exciter time constant (TB). Typical Value = 0.04.
Minimum AVR output (VRMN). Typical Value = -5.2.
Maximum AVR output (VRMX). Typical Value = 6.5.
Italian excitation system corresponding to IEEE (1968) Type 1 Model.
Italian excitation system corresponding to IEEE (1968) Type 1 Model. It represents exciter dynamo and electromechanical regulator.
Reference to the superclass object.
Field voltage value 1 (E1). Typical Value = 4.18.
Field voltage value 2 (E2). Typical Value = 3.14.
AVR gain (KA). Typical Value = 500.
Rate feedback gain (KF). Typical Value = 0.12.
Saturation factor at E1 (S(E1)). Typical Value = 0.1.
Saturation factor at E2 (S(E2)). Typical Value = 0.03.
AVR time constant (TA). Typical Value = 0.2.
AVR time constant (TB). Typical Value = 0.
Exciter time constant (TE). Typical Value = 1.
Rate feedback time constant (TF). Typical Value = 1.
Minimum AVR output (VRMN). Typical Value = -6.
Maximum AVR output (VRMX). Typical Value = 7.
Italian excitation system corresponding to IEEE (1968) Type 2 Model.
Italian excitation system corresponding to IEEE (1968) Type 2 Model. It represents alternator and rotating diodes and electromechanic voltage regulators.
Reference to the superclass object.
Field voltage value 1 (E1). Typical Value = 4.18.
Field voltage value 2 (E2). Typical Value = 3.14.
AVR gain (KA). Typical Value = 500.
Rate feedback gain (KF). Typical Value = 0.12.
Saturation factor at E1 (S(E1)). Typical Value = 0.1.
Saturation factor at E2 (S(E2)). Typical Value = 0.03.
AVR time constant (TA). Typical Value = 0.02.
AVR time constant (TB). Typical Value = 0.
Exciter time constant (TE). Typical Value = 1.
Rate feedback time constant (TF1). Typical Value = 1.
Rate feedback time constant (TF2). Typical Value = 1.
Minimum AVR output (VRMN). Typical Value = -6.
Maximum AVR output (VRMX). Typical Value = 7.
Italian excitation system.
Italian excitation system. It represents exciter dynamo and electric regulator.
Reference to the superclass object.
Field voltage value 1 (E1). Typical Value = 4.18.
Field voltage value 2 (E2). Typical Value = 3.14.
AVR gain (KA). Typical Value = 100.
Saturation factor at E1 (S(E1)). Typical Value = 0.1.
Saturation factor at E2 (S(E2)). Typical Value = 0.03.
AVR time constant (T1). Typical Value = 20.
AVR time constant (T2). Typical Value = 1.6.
AVR time constant (T3). Typical Value = 0.66.
AVR time constant (T4). Typical Value = 0.07.
Exciter time constant (TE). Typical Value = 1.
Minimum AVR output (VRMN). Typical Value = -7.5.
Maximum AVR output (VRMX). Typical Value = 7.5.
Italian excitation system.
Italian excitation system. It represents static exciter and electric voltage regulator.
Reference to the superclass object.
AVR output voltage dependency selector (Imul). true = selector is connected false = selector is not connected. Typical Value = true.
AVR gain (KA). Typical Value = 300.
Exciter gain (KE). Typical Value = 1.
Exciter internal reactance (KIF). Typical Value = 0.
AVR time constant (T1). Typical Value = 4.8.
Exciter current feedback time constant (T1IF). Typical Value = 60.
AVR time constant (T2). Typical Value = 1.5.
AVR time constant (T3). Typical Value = 0.
AVR time constant (T4). Typical Value = 0.
Exciter current feedback time constant (TIF). Typical Value = 0.
Minimum exciter output (VFMN). Typical Value = 0.
Maximum exciter output (VFMX). Typical Value = 5.
Minimum AVR output (VRMN). Typical Value = 0.
Maximum AVR output (VRMX). Typical Value = 5.
Manual excitation control with field circuit resistance.
Manual excitation control with field circuit resistance. This model can be used as a very simple representation of manual voltage control.
Reference to the superclass object.
Gain (Ka).
Effective Output Resistance (Rex). Rex represents the effective output resistance seen by the excitation system.
Time constant (Ta).
IVO excitation system.
IVO excitation system.
Reference to the superclass object.
Lead coefficient (A1). Typical Value = 0.5.
Lag coefficient (A2). Typical Value = 0.5.
Lead coefficient (A3). Typical Value = 0.5.
Lag coefficient (A4). Typical Value = 0.5.
Lead coefficient (A5). Typical Value = 0.5.
Lag coefficient (A6). Typical Value = 0.5.
Gain (K1). Typical Value = 1.
Gain (K3). Typical Value = 3.
Gain (K5). Typical Value = 1.
Lead time constant (T1). Typical Value = 0.05.
Lag time constant (T2). Typical Value = 0.1.
Lead time constant (T3). Typical Value = 0.1.
Lag time constant (T4). Typical Value = 0.1.
Lead time constant (T5). Typical Value = 0.1.
Lag time constant (T6). Typical Value = 0.1.
Lead-lag max. limit (Vmax1). Typical Value = 5.
Lead-lag max. limit (Vmax3). Typical Value = 5.
Lead-lag max. limit (Vmax5). Typical Value = 5.
Lead-lag min. limit (Vmin1). Typical Value = -5.
Lead-lag min. limit (Vmin3). Typical Value = -5.
Lead-lag min. limit (Vmin5). Typical Value = -2.
Transformer fed static excitation system (static with ABB regulator).
Transformer fed static excitation system (static with ABB regulator). This model represents a static excitation system in which a gated thyristor bridge fed by a transformer at the main generator terminals feeds the main generator directly.
Reference to the superclass object.
Maximum open circuit exciter voltage (Efdmax). Typical Value = 5.
Minimum open circuit exciter voltage (Efdmin). Typical Value = -5.
Steady state gain (K). Typical Value = 300.
Supplementary signal routing selector (switch). true = Vs connected to 3rd summing point false = Vs connected to 1st summing point (see diagram). Typical Value = true.
Controller time constant (T1). Typical Value = 6.
Controller time constant (T2). Typical Value = 1.
Lead/lag time constant (T3). Typical Value = 0.05.
Lead/lag time constant (T4). Typical Value = 0.01.
Maximum control element output (Vrmax). Typical Value = 5.
Minimum control element output (Vrmin). Typical Value = -5.
Effective excitation transformer reactance (Xe). Typical Value = 0.05.
Czech Proportion/Integral Exciter.
Czech Proportion/Integral Exciter.
Reference to the superclass object.
Exciter output maximum limit (Efdmax).
Exciter output minimum limit (Efdmin).
Regulator gain (Ka).
Exciter constant related to self-excited field (Ke).
Regulator proportional gain (Kp).
Regulator time constant (Ta).
Regulator integral time constant (Tc).
Exciter time constant, integration rate associated with exciter control (Te).
Voltage regulator maximum limit (Vrmax).
Voltage regulator minimum limit (Vrmin).
Modified IEEE DC1A direct current commutator exciter with speed input and without underexcitation limiters (UEL) inputs.
Modified IEEE DC1A direct current commutator exciter with speed input and without underexcitation limiters (UEL) inputs.
Reference to the superclass object.
Maximum voltage exciter output limiter (Efdmax). Typical Value = 99.
Exciter voltage at which exciter saturation is defined (Efd1). Typical Value = 3.1.
Exciter voltage at which exciter saturation is defined (Efd2). Typical Value = 2.3.
Minimum voltage exciter output limiter (Efdmin). Typical Value = -99.
(exclim). IEEE standard is ambiguous about lower limit on exciter output.
Voltage regulator gain (Ka). Typical Value = 46.
Exciter constant related to self-excited field (Ke). Typical Value = 0.
Excitation control system stabilizer gain (Kf). Typical Value = 0.1.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Efd1 (Se[Eefd1]). Typical Value = 0.33.
Exciter saturation function value at the corresponding exciter voltage, Efd1 (Se[Eefd1]). Typical Value = 0.33.
Voltage regulator time constant (Ta). Typical Value = 0.06.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 0.46.
Excitation control system stabilizer time constant (Tf). Typical Value = 1.
Maximum voltage regulator output (Vrmax). Typical Value = 1.
Minimum voltage regulator output (Vrmin). Typical Value = -0.9.
Modified IEEE DC2A direct current commutator exciters with speed input, one more leg block in feedback loop and without underexcitation limiters (UEL) inputs.
Modified IEEE DC2A direct current commutator exciters with speed input, one more leg block in feedback loop and without underexcitation limiters (UEL) inputs. DC type 2 excitation system model with added speed multiplier, added lead-lag, and voltage-dependent limits.
Reference to the superclass object.
Exciter voltage at which exciter saturation is defined (Efd1). Typical Value = 3.05.
Exciter voltage at which exciter saturation is defined (Efd2). Typical Value = 2.29.
(exclim). IEEE standard is ambiguous about lower limit on exciter output.
Voltage regulator gain (Ka). Typical Value = 300.
Exciter constant related to self-excited field (Ke). If Ke is entered as zero, the model calculates an effective value of Ke such that the initial condition value of Vr is zero. The zero value of Ke is not changed. If Ke is entered as non-zero, its value is used directly, without change. Typical Value = 1.
Excitation control system stabilizer gain (Kf). Typical Value = 0.1.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Efd1 (Se[Eefd1]). Typical Value = 0.279.
Exciter saturation function value at the corresponding exciter voltage, Efd2 (Se[Efd2]). Typical Value = 0.117.
Voltage regulator time constant (Ta). Typical Value = 0.01.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 1.33.
Excitation control system stabilizer time constant (Tf). Typical Value = 0.675.
Excitation control system stabilizer time constant (Tf1). Typical Value = 0.
Maximum voltage regulator output (Vrmax). Typical Value = 4.95.
Minimum voltage regulator output (Vrmin). Typical Value = -4.9.
(Vtlim). true = limiter at the block [Ka/(1+sTa)] is dependent on Vt false = limiter at the block is not dependent on Vt. Typical Value = true.
This is modified IEEE DC3A direct current commutator exciters with speed input, and death band.
This is modified IEEE DC3A direct current commutator exciters with speed input, and death band. DC old type 4.
Reference to the superclass object.
Maximum voltage exciter output limiter (Efdmax). Typical Value = 99.
Exciter voltage at which exciter saturation is defined (Efd1). Typical Value = 2.6.
Exciter voltage at which exciter saturation is defined (Efd2). Typical Value = 3.45.
(Efdlim). true = exciter output limiter is active false = exciter output limiter not active. Typical Value = true.
Minimum voltage exciter output limiter (Efdmin). Typical Value = -99.
(exclim). IEEE standard is ambiguous about lower limit on exciter output.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Death band (Kr). If Kr is not zero, the voltage regulator input changes at a constant rate if Verr > Kr or Verr < -Kr as per the IEEE (1968) Type 4 model. If Kr is zero, the error signal drives the voltage regulator continuously as per the IEEE (1980) DC3 and IEEE (1992, 2005) DC3A models. Typical Value = 0.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Fast raise/lower contact setting (Kv). Typical Value = 0.05.
Exciter saturation function value at the corresponding exciter voltage, Efd1 (Se[Eefd1]). Typical Value = 0.1.
Exciter saturation function value at the corresponding exciter voltage, Efd2 (Se[Efd2]). Typical Value = 0.35.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 1.83.
Rheostat travel time (Trh). Typical Value = 20.
Maximum voltage regulator output (Vrmax). Typical Value = 5.
Minimum voltage regulator output (Vrmin). Typical Value = 0.
This is modified old IEEE type 3 excitation system.
This is modified old IEEE type 3 excitation system.
Reference to the superclass object.
(exclim). true = lower limit of zero is applied to integrator output false = lower limit of zero not applied to integrator output. Typical Value = true.
Voltage regulator gain (Ka). Typical Value = 300.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Excitation control system stabilizer gain (Kf). Typical Value = 0.1.
Potential circuit gain coefficient (Ki). Typical Value = 4.83.
Potential circuit gain coefficient (Kp). Typical Value = 4.37.
Voltage regulator time constant (Ta). Typical Value = 0.01.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 1.83.
Excitation control system stabilizer time constant (Tf). Typical Value = 0.675.
Available exciter voltage limiter (Vb1max). Typical Value = 11.63.
Vb limiter indicator. true = exciter Vbmax limiter is active false = Vb1max is active. Typical Value = true.
Available exciter voltage limiter (Vbmax). Typical Value = 11.63.
Maximum voltage regulator output (Vrmax). Typical Value = 5.
Minimum voltage regulator output (Vrmin). Typical Value = 0.
Static PI transformer fed excitation system: ELIN (VATECH) - simplified model.
Static PI transformer fed excitation system: ELIN (VATECH) - simplified model. This model represents an all-static excitation system. A PI voltage controller establishes a desired field current set point for a proportional current controller. The integrator of the PI controller has a follow-up input to match its signal to the present field current. A power system stabilizer with power input is included in the model.
Reference to the superclass object.
Controller follow up dead band (Dpnf). Typical Value = 0.
Maximum open circuit excitation voltage (Efmax). Typical Value = 5.
Minimum open circuit excitation voltage (Efmin). Typical Value = -5.
Stabilizer Gain 1 (Ks1). Typical Value = 0.
Stabilizer Gain 2 (Ks2). Typical Value = 0.
Stabilizer Limit Output (smax). Typical Value = 0.1.
Current transducer time constant (Tfi). Typical Value = 0.
Controller reset time constant (Tnu). Typical Value = 2.
Stabilizer Phase Lag Time Constant (Ts1). Typical Value = 1.
Stabilizer Filter Time Constant (Ts2). Typical Value = 1.
Stabilizer parameters (Tsw). Typical Value = 3.
Current controller gain (Vpi). Typical Value = 12.45.
Controller follow up gain (Vpnf). Typical Value = 2.
Voltage controller proportional gain (Vpu). Typical Value = 34.5.
Excitation transformer effective reactance (Xe) (>=0). Xe represents the regulation of the transformer/rectifier unit. Typical Value = 0.06.
Detailed Excitation System Model - ELIN (VATECH).
Detailed Excitation System Model - ELIN (VATECH). This model represents an all-static excitation system. A PI voltage controller establishes a desired field current set point for a proportional current controller. The integrator of the PI controller has a follow-up input to match its signal to the present field current. Power system stabilizer models used in conjunction with this excitation system model: PssELIN2, PssIEEE2B, Pss2B.
Reference to the superclass object.
Gain (Efdbas). Typical Value = 0.1.
Limiter (Iefmax). Typical Value = 1.
Minimum open circuit excitation voltage (Iefmax2). Typical Value = -5.
Limiter (Iefmin). Typical Value = 1.
Voltage regulator input gain (K1). Typical Value = 0.
Voltage regulator input limit (K1ec). Typical Value = 2.
Gain (K2). Typical Value = 5.
Gain (K3). Typical Value = 0.1.
Gain (K4). Typical Value = 0.
Voltage controller derivative gain (Kd1). Typical Value = 34.5.
Gain (Ke2). Typical Value = 0.1.
Gain (Ketb). Typical Value = 0.06.
Controller follow up gain (PID1max). Typical Value = 2.
Exciter saturation function value at the corresponding exciter voltage, Ve1, back of commutating reactance (Se[Ve1]). Typical Value = 0.
Exciter saturation function value at the corresponding exciter voltage, Ve2, back of commutating reactance (Se[Ve2]). Typical Value = 1.
Voltage controller derivative washout time constant (Tb1). Typical Value = 12.45.
Time constant (Te). Typical Value = 0.
Time Constant (Te2). Typical Value = 1.
Controller follow up dead band (Ti1). Typical Value = 0.
Time constant (Ti3). Typical Value = 3.
Time constant (Ti4). Typical Value = 0.
Time constant (Tr4). Typical Value = 1.
Limiter (Upmax). Typical Value = 3.
Limiter (Upmin). Typical Value = 0.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve1). Typical Value = 3.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (Ve2). Typical Value = 0.
Excitation transformer effective reactance (Xp). Typical Value = 1.
Hungarian Excitation System Model, with built-in voltage transducer.
Hungarian Excitation System Model, with built-in voltage transducer.
Reference to the superclass object.
Major loop PI tag gain factor (Ae). Typical Value = 3.
Minor loop PI tag gain factor (Ai). Typical Value = 22.
AVR constant (Atr). Typical Value = 2.19.
Field voltage control signal upper limit on AVR base (Emax). Typical Value = 0.996.
Field voltage control signal lower limit on AVR base (Emin). Typical Value = -0.866.
Major loop PI tag output signal upper limit (Imax). Typical Value = 2.19.
Major loop PI tag output signal lower limit (Imin). Typical Value = 0.1.
Voltage base conversion constant (Ke). Typical Value = 4.666.
Current base conversion constant (Ki). Typical Value = 0.21428.
Major loop PI tag integration time constant (Te). Typical Value = 0.154.
Minor loop PI control tag integration time constant (Ti). Typical Value = 0.01333.
Filter time constant (Tr). If a voltage compensator is used in conjunction with this excitation system model, Tr should be set to 0. Typical Value = 0.01.
The class represents IEEE Std 421.5-2005 type AC1A model.
The class represents IEEE Std 421.5-2005 type AC1A model. The model represents the field-controlled alternator-rectifier excitation systems designated Type AC1A. These excitation systems consist of an alternator main exciter with non-controlled rectifiers.
Reference to the superclass object.
Voltage regulator gain (KA). Typical Value = 400.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.2.
Demagnetizing factor, a function of exciter alternator reactances (KD). Typical Value = 0.38.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gains (KF). Typical Value = 0.03.
Exciter saturation function value at the corresponding exciter voltage, VE1, back of commutating reactance (SE[VE1]). Typical Value = 0.1.
Exciter saturation function value at the corresponding exciter voltage, VE2, back of commutating reactance (SE[VE2]). Typical Value = 0.03.
Voltage regulator time constant (TA). Typical Value = 0.02.
Voltage regulator time constant (TB). Typical Value = 0.
Voltage regulator time constant (TC). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.8.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
Maximum voltage regulator output (VAMAX). Typical Value = 14.5.
Minimum voltage regulator output (VAMIN). Typical Value = -14.5.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE1). Typical Value = 4.18.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE2). Typical Value = 3.14.
Maximum voltage regulator outputs (VRMAX). Typical Value = 6.03.
Minimum voltage regulator outputs (VRMIN). Typical Value = -5.43.
The class represents IEEE Std 421.5-2005 type AC2A model.
The class represents IEEE Std 421.5-2005 type AC2A model. The model represents a high initial response field-controlled alternator-rectifier excitation system. The alternator main exciter is used with non-controlled rectifiers. The Type AC2A model is similar to that of Type AC1A except for the inclusion of exciter time constant compensation and exciter field current limiting elements.
Reference to the superclass object.
Voltage regulator gain (KA). Typical Value = 400.
Second stage regulator gain (KB). Typical Value = 25.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.28.
Demagnetizing factor, a function of exciter alternator reactances (KD). Typical Value = 0.35.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gains (KF). Typical Value = 0.03.
Exciter field current feedback gain (KH). Typical Value = 1.
Exciter saturation function value at the corresponding exciter voltage, VE1, back of commutating reactance (SE[VE1]). Typical Value = 0.037.
Exciter saturation function value at the corresponding exciter voltage, VE2, back of commutating reactance (SE[VE2]). Typical Value = 0.012.
Voltage regulator time constant (TA). Typical Value = 0.02.
Voltage regulator time constant (TB). Typical Value = 0.
Voltage regulator time constant (TC). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.6.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
Maximum voltage regulator output (VAMAX). Typical Value = 8.
Minimum voltage regulator output (VAMIN). Typical Value = -8.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE1). Typical Value = 4.4.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE2). Typical Value = 3.3.
Exciter field current limit reference (VFEMAX). Typical Value = 4.4.
Maximum voltage regulator outputs (VRMAX). Typical Value = 105.
Minimum voltage regulator outputs (VRMIN). Typical Value = -95.
The class represents IEEE Std 421.5-2005 type AC3A model.
The class represents IEEE Std 421.5-2005 type AC3A model. The model represents the field-controlled alternator-rectifier excitation systems designated Type AC3A. These excitation systems include an alternator main exciter with non-controlled rectifiers. The exciter employs self-excitation, and the voltage regulator power is derived from the exciter output voltage. Therefore, this system has an additional nonlinearity, simulated by the use of a multiplier
Reference to the superclass object.
Value of EFD at which feedback gain changes (EFDN). Typical Value = 2.36.
Voltage regulator gain (KA). Typical Value = 45.62.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.104.
Demagnetizing factor, a function of exciter alternator reactances (KD). Typical Value = 0.499.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gains (KF). Typical Value = 0.143.
Excitation control system stabilizer gain (KN). Typical Value = 0.05.
Constant associated with regulator and alternator field power supply (KR). Typical Value = 3.77.
Exciter saturation function value at the corresponding exciter voltage, VE1, back of commutating reactance (SE[VE1]). Typical Value = 1.143.
Exciter saturation function value at the corresponding exciter voltage, VE2, back of commutating reactance (SE[VE2]). Typical Value = 0.1.
Voltage regulator time constant (TA). Typical Value = 0.013.
Voltage regulator time constant (TB). Typical Value = 0.
Voltage regulator time constant (TC). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 1.17.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
Maximum voltage regulator output (VAMAX). Typical Value = 1.
Minimum voltage regulator output (VAMIN). Typical Value = -0.95.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE1) equals VEMAX (VE1). Typical Value = 6.24.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE2). Typical Value = 4.68.
Minimum exciter voltage output (VEMIN). Typical Value = 0.1.
Exciter field current limit reference (VFEMAX). Typical Value = 16.
The class represents IEEE Std 421.5-2005 type AC4A model.
The class represents IEEE Std 421.5-2005 type AC4A model. The model represents type AC4A alternator-supplied controlled-rectifier excitation system which is quite different from the other type ac systems. This high initial response excitation system utilizes a full thyristor bridge in the exciter output circuit. The voltage regulator controls the firing of the thyristor bridges. The exciter alternator uses an independent voltage regulator to control its output voltage to a constant value. These effects are not modeled; however, transient loading effects on the exciter alternator are included.
Reference to the superclass object.
Voltage regulator gain (KA). Typical Value = 200.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.
Voltage regulator time constant (TA). Typical Value = 0.015.
Voltage regulator time constant (TB). Typical Value = 10.
Voltage regulator time constant (TC). Typical Value = 1.
Maximum voltage regulator input limit (VIMAX). Typical Value = 10.
Minimum voltage regulator input limit (VIMIN). Typical Value = -10.
Maximum voltage regulator output (VRMAX). Typical Value = 5.64.
Minimum voltage regulator output (VRMIN). Typical Value = -4.53.
The class represents IEEE Std 421.5-2005 type AC5A model.
The class represents IEEE Std 421.5-2005 type AC5A model. The model represents a simplified model for brushless excitation systems. The regulator is supplied from a source, such as a permanent magnet generator, which is not affected by system disturbances. Unlike other ac models, this model uses loaded rather than open circuit exciter saturation data in the same way as it is used for the dc models. Because the model has been widely implemented by the industry, it is sometimes used to represent other types of systems when either detailed data for them are not available or simplified models are required.
Reference to the superclass object.
Exciter voltage at which exciter saturation is defined (EFD1). Typical Value = 5.6.
Exciter voltage at which exciter saturation is defined (EFD2). Typical Value = 4.2.
Voltage regulator gain (KA). Typical Value = 400.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gains (KF). Typical Value = 0.03.
Exciter saturation function value at the corresponding exciter voltage, EFD1 (SE[EFD1]). Typical Value = 0.86.
Exciter saturation function value at the corresponding exciter voltage, EFD2 (SE[EFD2]). Typical Value = 0.5.
Voltage regulator time constant (TA). Typical Value = 0.02.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.8.
Excitation control system stabilizer time constant (TF1). Typical Value = 1.
Excitation control system stabilizer time constant (TF2). Typical Value = 1.
Excitation control system stabilizer time constant (TF3). Typical Value = 1.
Maximum voltage regulator output (VRMAX). Typical Value = 7.3.
Minimum voltage regulator output (VRMIN). Typical Value = -7.3.
The class represents IEEE Std 421.5-2005 type AC6A model.
The class represents IEEE Std 421.5-2005 type AC6A model. The model represents field-controlled alternator-rectifier excitation systems with system-supplied electronic voltage regulators. The maximum output of the regulator, VR, is a function of terminal voltage, VT. The field current limiter included in the original model AC6A remains in the 2005 update.
Reference to the superclass object.
Voltage regulator gain (KA). Typical Value = 536.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.173.
Demagnetizing factor, a function of exciter alternator reactances (KD). Typical Value = 1.91.
Exciter constant related to self-excited field (KE). Typical Value = 1.6.
Exciter field current limiter gain (KH). Typical Value = 92.
Exciter saturation function value at the corresponding exciter voltage, VE1, back of commutating reactance (SE[VE1]). Typical Value = 0.214.
Exciter saturation function value at the corresponding exciter voltage, VE2, back of commutating reactance (SE[VE2]). Typical Value = 0.044.
Voltage regulator time constant (TA). Typical Value = 0.086.
Voltage regulator time constant (TB). Typical Value = 9.
Voltage regulator time constant (TC). Typical Value = 3.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 1.
Exciter field current limiter time constant (TH). Typical Value = 0.08.
Exciter field current limiter time constant (TJ). Typical Value = 0.02.
Voltage regulator time constant (TK). Typical Value = 0.18.
Maximum voltage regulator output (VAMAX). Typical Value = 75.
Minimum voltage regulator output (VAMIN). Typical Value = -75.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE1) equals VEMAX (VE1). Typical Value = 7.4.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE2). Typical Value = 5.55.
Exciter field current limit reference (VFELIM). Typical Value = 19.
Maximum field current limiter signal reference (VHMAX). Typical Value = 75.
Maximum voltage regulator output (VRMAX). Typical Value = 44.
Minimum voltage regulator output (VRMIN). Typical Value = -36.
The class represents IEEE Std 421.5-2005 type AC7B model.
The class represents IEEE Std 421.5-2005 type AC7B model. The model represents excitation systems which consist of an ac alternator with either stationary or rotating rectifiers to produce the dc field requirements. It is an upgrade to earlier ac excitation systems, which replace only the controls but retain the ac alternator and diode rectifier bridge.
Reference to the superclass object.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.18.
Demagnetizing factor, a function of exciter alternator reactances (KD). Typical Value = 0.02.
Voltage regulator derivative gain (KDR). Typical Value = 0.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gain (KF1). Typical Value = 0.212.
Excitation control system stabilizer gain (KF2). Typical Value = 0.
Excitation control system stabilizer gain (KF3). Typical Value = 0.
Voltage regulator integral gain (KIA). Typical Value = 59.69.
Voltage regulator integral gain (KIR). Typical Value = 4.24.
Exciter field voltage lower limit parameter (KL). Typical Value = 10.
Potential circuit gain coefficient (KP). Typical Value = 4.96.
Voltage regulator proportional gain (KPA). Typical Value = 65.36.
Voltage regulator proportional gain (KPR). Typical Value = 4.24.
Exciter saturation function value at the corresponding exciter voltage, VE1, back of commutating reactance (SE[VE1]). Typical Value = 0.44.
Exciter saturation function value at the corresponding exciter voltage, VE2, back of commutating reactance (SE[VE2]). Typical Value = 0.075.
Lag time constant (TDR). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 1.1.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
Maximum voltage regulator output (VAMAX). Typical Value = 1.
Minimum voltage regulator output (VAMIN). Typical Value = -0.95.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE1) equals VEMAX (VE1). Typical Value = 6.3.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE2). Typical Value = 3.02.
Minimum exciter voltage output (VEMIN). Typical Value = 0.
Exciter field current limit reference (VFEMAX). Typical Value = 6.9.
Maximum voltage regulator output (VRMAX). Typical Value = 5.79.
Minimum voltage regulator output (VRMIN). Typical Value = -5.79.
The class represents IEEE Std 421.5-2005 type AC8B model.
The class represents IEEE Std 421.5-2005 type AC8B model. This model represents a PID voltage regulator with either a brushless exciter or dc exciter. The AVR in this model consists of PID control, with separate constants for the proportional (KPR), integral (KIR), and derivative (KDR) gains. The representation of the brushless exciter (TE, KE, SE, KC, KD) is similar to the model Type AC2A. The Type AC8B model can be used to represent static voltage regulators applied to brushless excitation systems. Digitally based voltage regulators feeding dc rotating main exciters can be represented with the AC Type AC8B model with the parameters KC and KD set to 0. For thyristor power stages fed from the generator terminals, the limits VRMAX and VRMIN should be a function of terminal voltage: VT * VRMAX and VT * VRMIN.
Reference to the superclass object.
Voltage regulator gain (KA). Typical Value = 1.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.55.
Demagnetizing factor, a function of exciter alternator reactances (KD). Typical Value = 1.1.
Voltage regulator derivative gain (KDR). Typical Value = 10.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Voltage regulator integral gain (KIR). Typical Value = 5.
Voltage regulator proportional gain (KPR). Typical Value = 80.
Exciter saturation function value at the corresponding exciter voltage, VE1, back of commutating reactance (SE[VE1]). Typical Value = 0.3.
Exciter saturation function value at the corresponding exciter voltage, VE2, back of commutating reactance (SE[VE2]). Typical Value = 3.
Voltage regulator time constant (TA). Typical Value = 0.
Lag time constant (TDR). Typical Value = 0.1.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 1.2.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE1) equals VEMAX (VE1). Typical Value = 6.5.
Exciter alternator output voltages back of commutating reactance at which saturation is defined (VE2). Typical Value = 9.
Minimum exciter voltage output (VEMIN). Typical Value = 0.
Exciter field current limit reference (VFEMAX). Typical Value = 6.
Maximum voltage regulator output (VRMAX). Typical Value = 35.
Minimum voltage regulator output (VRMIN). Typical Value = 0.
The class represents IEEE Std 421.5-2005 type DC1A model.
The class represents IEEE Std 421.5-2005 type DC1A model. This model represents field-controlled dc commutator exciters with continuously acting voltage regulators (especially the direct-acting rheostatic, rotating amplifier, and magnetic amplifier types). Because this model has been widely implemented by the industry, it is sometimes used to represent other types of systems when detailed data for them are not available or when a simplified model is required.
Reference to the superclass object.
Exciter voltage at which exciter saturation is defined (EFD1). Typical Value = 3.1.
Exciter voltage at which exciter saturation is defined (EFD2). Typical Value = 2.3.
(exclim). IEEE standard is ambiguous about lower limit on exciter output.
Voltage regulator gain (KA). Typical Value = 46.
Exciter constant related to self-excited field (KE). Typical Value = 0.
Excitation control system stabilizer gain (KF). Typical Value = 0.1.
Exciter saturation function value at the corresponding exciter voltage, EFD1 (SE[EFD1]). Typical Value = 0.33.
Exciter saturation function value at the corresponding exciter voltage, EFD2 (SE[EFD2]). Typical Value = 0.1.
Voltage regulator time constant (TA). Typical Value = 0.06.
Voltage regulator time constant (TB). Typical Value = 0.
Voltage regulator time constant (TC). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.46.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
UEL input (uelin). true = input is connected to the HV gate false = input connects to the error signal. Typical Value = true.
Maximum voltage regulator output (VRMAX). Typical Value = 1.
Minimum voltage regulator output (VRMIN). Typical Value = -0.9.
The class represents IEEE Std 421.5-2005 type DC2A model.
The class represents IEEE Std 421.5-2005 type DC2A model. This model represents represent field-controlled dc commutator exciters with continuously acting voltage regulators having supplies obtained from the generator or auxiliary bus. It differs from the Type DC1A model only in the voltage regulator output limits, which are now proportional to terminal voltage VT.
Reference to the superclass object.
Exciter voltage at which exciter saturation is defined (EFD1). Typical Value = 3.05.
Exciter voltage at which exciter saturation is defined (EFD2). Typical Value = 2.29.
(exclim). IEEE standard is ambiguous about lower limit on exciter output. Typical Value = - 999 which means that there is no limit applied.
Voltage regulator gain (KA). Typical Value = 300.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gain (KF). Typical Value = 0.1.
Exciter saturation function value at the corresponding exciter voltage, EFD1 (SE[EFD1]). Typical Value = 0.279.
Exciter saturation function value at the corresponding exciter voltage, EFD2 (SE[EFD2]). Typical Value = 0.117.
Voltage regulator time constant (TA). Typical Value = 0.01.
Voltage regulator time constant (TB). Typical Value = 0.
Voltage regulator time constant (TC). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 1.33.
Excitation control system stabilizer time constant (TF). Typical Value = 0.675.
UEL input (uelin). true = input is connected to the HV gate false = input connects to the error signal. Typical Value = true.
Maximum voltage regulator output (VRMAX). Typical Value = 4.95.
Minimum voltage regulator output (VRMIN). Typical Value = -4.9.
The class represents IEEE Std 421.5-2005 type DC3A model.
The class represents IEEE Std 421.5-2005 type DC3A model. This model represents represent older systems, in particular those dc commutator exciters with non-continuously acting regulators that were commonly used before the development of the continuously acting varieties. These systems respond at basically two different rates, depending upon the magnitude of voltage error. For small errors, adjustment is made periodically with a signal to a motor-operated rheostat. Larger errors cause resistors to be quickly shorted or inserted and a strong forcing signal applied to the exciter. Continuous motion of the motor-operated rheostat occurs for these larger error signals, even though it is bypassed by contactor action.
Reference to the superclass object.
Exciter voltage at which exciter saturation is defined (EFD1). Typical Value = 3.375.
Exciter voltage at which exciter saturation is defined (EFD2). Typical Value = 3.15.
(exclim). IEEE standard is ambiguous about lower limit on exciter output.
Exciter constant related to self-excited field (KE). Typical Value = 0.05.
Fast raise/lower contact setting (KV). Typical Value = 0.05.
Exciter saturation function value at the corresponding exciter voltage, EFD1 (SE[EFD1]). Typical Value = 0.267.
Exciter saturation function value at the corresponding exciter voltage, EFD2 (SE[EFD2]). Typical Value = 0.068.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.5.
Rheostat travel time (TRH). Typical Value = 20.
Maximum voltage regulator output (VRMAX). Typical Value = 1.
Minimum voltage regulator output (VRMIN). Typical Value = 0.
The class represents IEEE Std 421.5-2005 type DC4B model.
The class represents IEEE Std 421.5-2005 type DC4B model. These excitation systems utilize a field-controlled dc commutator exciter with a continuously acting voltage regulator having supplies obtained from the generator or auxiliary bus.
Reference to the superclass object.
Exciter voltage at which exciter saturation is defined (EFD1). Typical Value = 1.75.
Exciter voltage at which exciter saturation is defined (EFD2). Typical Value = 2.33.
Voltage regulator gain (KA). Typical Value = 1.
Regulator derivative gain (KD). Typical Value = 20.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gain (KF). Typical Value = 0.
Regulator integral gain (KI). Typical Value = 20.
Regulator proportional gain (KP). Typical Value = 20.
OEL input (OELin). true = LV gate false = subtract from error signal. Typical Value = true.
Exciter saturation function value at the corresponding exciter voltage, EFD1 (SE[EFD1]). Typical Value = 0.08.
Exciter saturation function value at the corresponding exciter voltage, EFD2 (SE[EFD2]). Typical Value = 0.27.
Voltage regulator time constant (TA). Typical Value = 0.2.
Regulator derivative filter time constant(TD). Typical Value = 0.01.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.8.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
UEL input (UELin). true = HV gate false = add to error signal. Typical Value = true.
Minimum exciter voltage output(VEMIN). Typical Value = 0.
Maximum voltage regulator output (VRMAX). Typical Value = 2.7.
Minimum voltage regulator output (VRMIN). Typical Value = -0.9.
The class represents IEEE Std 421.5-2005 type ST1A model.
The class represents IEEE Std 421.5-2005 type ST1A model. This model represents systems in which excitation power is supplied through a transformer from the generator terminals (or the unit�s auxiliary bus) and is regulated by a controlled rectifier. The maximum exciter voltage available from such systems is directly related to the generator terminal voltage.
Reference to the superclass object.
Exciter output current limit reference (ILR). Typical Value = 0.
Voltage regulator gain (KA). Typical Value = 190.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.08.
Excitation control system stabilizer gains (KF). Typical Value = 0.
Exciter output current limiter gain (KLR). Typical Value = 0.
Selector of the Power System Stabilizer (PSS) input (PSSin). true = PSS input (Vs) added to error signal false = PSS input (Vs) added to voltage regulator output. Typical Value = true.
Voltage regulator time constant (TA). Typical Value = 0.
Voltage regulator time constant (TB). Typical Value = 10.
Voltage regulator time constant (TB1). Typical Value = 0.
Voltage regulator time constant (TC). Typical Value = 1.
Voltage regulator time constant (TC1). Typical Value = 0.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
Selector of the connection of the UEL input (UELin). Typical Value = ignoreUELsignal.
Maximum voltage regulator output (VAMAX). Typical Value = 14.5.
Minimum voltage regulator output (VAMIN). Typical Value = -14.5.
Maximum voltage regulator input limit (VIMAX). Typical Value = 999.
Minimum voltage regulator input limit (VIMIN). Typical Value = -999.
Maximum voltage regulator outputs (VRMAX). Typical Value = 7.8.
Minimum voltage regulator outputs (VRMIN). Typical Value = -6.7.
The class represents IEEE Std 421.5-2005 type ST2A model.
The class represents IEEE Std 421.5-2005 type ST2A model. Some static systems utilize both current and voltage sources (generator terminal quantities) to comprise the power source. The regulator controls the exciter output through controlled saturation of the power transformer components. These compound-source rectifier excitation systems are designated Type ST2A and are represented by ExcIEEEST2A.
Reference to the superclass object.
Maximum field voltage (EFDMax). Typical Value = 99.
Voltage regulator gain (KA). Typical Value = 120.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 1.82.
Exciter constant related to self-excited field (KE). Typical Value = 1.
Excitation control system stabilizer gains (KF). Typical Value = 0.05.
Potential circuit gain coefficient (KI). Typical Value = 8.
Potential circuit gain coefficient (KP). Typical Value = 4.88.
Voltage regulator time constant (TA). Typical Value = 0.15.
Exciter time constant, integration rate associated with exciter control (TE). Typical Value = 0.5.
Excitation control system stabilizer time constant (TF). Typical Value = 1.
UEL input (UELin). true = HV gate false = add to error signal. Typical Value = true.
Maximum voltage regulator outputs (VRMAX). Typical Value = 1.
Minimum voltage regulator outputs (VRMIN). Typical Value = 0.
The class represents IEEE Std 421.5-2005 type ST3A model.
The class represents IEEE Std 421.5-2005 type ST3A model. Some static systems utilize a field voltage control loop to linearize the exciter control characteristic. This also makes the output independent of supply source variations until supply limitations are reached. These systems utilize a variety of controlled-rectifier designs: full thyristor complements or hybrid bridges
Reference to the superclass object.
Voltage regulator gain (KA). This is parameter K in the IEEE Std. Typical Value = 200.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.2.
Feedback gain constant of the inner loop field regulator (KG). Typical Value = 1.
Potential circuit gain coefficient (KI). Typical Value = 0.
Forward gain constant of the inner loop field regulator (KM). Typical Value = 7.93.
Potential circuit gain coefficient (KP). Typical Value = 6.15.
Voltage regulator time constant (TA). Typical Value = 0.
Voltage regulator time constant (TB). Typical Value = 10.
Voltage regulator time constant (TC). Typical Value = 1.
Potential circuit phase angle (thetap). Typical Value = 0.
Forward time constant of inner loop field regulator (TM). Typical Value = 0.4.
Maximum excitation voltage (VBMax). Typical Value = 6.9.
Maximum inner loop feedback voltage (VGMax). Typical Value = 5.8.
Maximum voltage regulator input limit (VIMAX). Typical Value = 0.2.
Minimum voltage regulator input limit (VIMIN). Typical Value = -0.2.
Maximum inner loop output (VMMax). Typical Value = 1.
Minimum inner loop output (VMMin). Typical Value = 0.
Maximum voltage regulator output (VRMAX). Typical Value = 10.
Minimum voltage regulator output (VRMIN). Typical Value = -10.
Reactance associated with potential source (XL). Typical Value = 0.081.
The class represents IEEE Std 421.5-2005 type ST4B model.
The class represents IEEE Std 421.5-2005 type ST4B model. This model is a variation of the Type ST3A model, with a proportional plus integral (PI) regulator block replacing the lag-lead regulator characteristic that is in the ST3A model. Both potential and compound source rectifier excitation systems are modeled. The PI regulator blocks have non-windup limits that are represented. The voltage regulator of this model is typically implemented digitally.
Reference to the superclass object.
Rectifier loading factor proportional to commutating reactance (KC). Typical Value = 0.113.
Feedback gain constant of the inner loop field regulator (KG). Typical Value = 0.
Potential circuit gain coefficient (KI). Typical Value = 0.
Voltage regulator integral gain output (KIM). Typical Value = 0.
Voltage regulator integral gain (KIR). Typical Value = 10.75.
Potential circuit gain coefficient (KP). Typical Value = 9.3.
Voltage regulator proportional gain output (KPM). Typical Value = 1.
Voltage regulator proportional gain (KPR). Typical Value = 10.75.
Voltage regulator time constant (TA). Typical Value = 0.02.
Potential circuit phase angle (thetap). Typical Value = 0.
Maximum excitation voltage (VBMax). Typical Value = 11.63.
Maximum inner loop output (VMMax). Typical Value = 99.
Minimum inner loop output (VMMin). Typical Value = -99.
Maximum voltage regulator output (VRMAX). Typical Value = 1.
Minimum voltage regulator output (VRMIN). Typical Value = -0.87.
Reactance associated with potential source (XL). Typical Value = 0.124.
The class represents IEEE Std 421.5-2005 type ST5B model.
The class represents IEEE Std 421.5-2005 type ST5B model. The Type ST5B excitation system is a variation of the Type ST1A model, with alternative overexcitation and underexcitation inputs and additional limits.
Reference to the superclass object.
Rectifier regulation factor (KC). Typical Value = 0.004.
Regulator gain (KR). Typical Value = 200.
Firing circuit time constant (T1). Typical Value = 0.004.
Regulator lag time constant (TB1). Typical Value = 6.
Regulator lag time constant (TB2). Typical Value = 0.01.
Regulator lead time constant (TC1). Typical Value = 0.8.
Regulator lead time constant (TC2). Typical Value = 0.08.
OEL lag time constant (TOB1). Typical Value = 2.
OEL lag time constant (TOB2). Typical Value = 0.08.
OEL lead time constant (TOC1). Typical Value = 0.1.
OEL lead time constant (TOC2). Typical Value = 0.08.
UEL lag time constant (TUB1). Typical Value = 10.
UEL lag time constant (TUB2). Typical Value = 0.05.
UEL lead time constant (TUC1). Typical Value = 2.
UEL lead time constant (TUC2). Typical Value = 0.1.
Maximum voltage regulator output (VRMAX). Typical Value = 5.
Minimum voltage regulator output (VRMIN). Typical Value = -4.
The class represents IEEE Std 421.5-2005 type ST6B model.
The class represents IEEE Std 421.5-2005 type ST6B model. This model consists of a PI voltage regulator with an inner loop field voltage regulator and pre-control. The field voltage regulator implements a proportional control. The pre-control and the delay in the feedback circuit increase the dynamic response.
Reference to the superclass object.
Exciter output current limit reference (ILR). Typical Value = 4.164.
Exciter output current limit adjustment (KCI). Typical Value = 1.0577.
Pre-control gain constant of the inner loop field regulator (KFF). Typical Value = 1.
Feedback gain constant of the inner loop field regulator (KG). Typical Value = 1.
Voltage regulator integral gain (KIA). Typical Value = 45.094.
Exciter output current limiter gain (KLR). Typical Value = 17.33.
Forward gain constant of the inner loop field regulator (KM). Typical Value = 1.
Voltage regulator proportional gain (KPA). Typical Value = 18.038.
OEL input selector (OELin). Typical Value = noOELinput.
Feedback time constant of inner loop field voltage regulator (TG). Typical Value = 0.02.
Maximum voltage regulator output (VAMAX). Typical Value = 4.81.
Minimum voltage regulator output (VAMIN). Typical Value = -3.85.
Maximum voltage regulator output (VRMAX). Typical Value = 4.81.
Minimum voltage regulator output (VRMIN). Typical Value = -3.85.
The class represents IEEE Std 421.5-2005 type ST7B model.
The class represents IEEE Std 421.5-2005 type ST7B model. This model is representative of static potential-source excitation systems. In this system, the AVR consists of a PI voltage regulator. A phase lead-lag filter in series allows introduction of a derivative function, typically used with brushless excitation systems. In that case, the regulator is of the PID type. In addition, the terminal voltage channel includes a phase lead-lag filter. The AVR includes the appropriate inputs on its reference for overexcitation limiter (OEL1), underexcitation limiter (UEL), stator current limiter (SCL), and current compensator (DROOP). All these limitations, when they work at voltage reference level, keep the PSS (VS signal from Type PSS1A, PSS2A, or PSS2B) in operation. However, the UEL limitation can also be transferred to the high value (HV) gate acting on the output signal. In addition, the output signal passes through a low value (LV) gate for a ceiling overexcitation limiter (OEL2).
Reference to the superclass object.
High-value gate feedback gain (KH). Typical Value 1.
Voltage regulator integral gain (KIA). Typical Value = 1.
Low-value gate feedback gain (KL). Typical Value 1.
Voltage regulator proportional gain (KPA). Typical Value = 40.
OEL input selector (OELin). Typical Value = noOELinput.
Regulator lag time constant (TB). Typical Value 1.
Regulator lead time constant (TC). Typical Value 1.
Excitation control system stabilizer time constant (TF). Typical Value 1.
Feedback time constant of inner loop field voltage regulator (TG). Typical Value 1.
Feedback time constant (TIA). Typical Value = 3.
UEL input selector (UELin). Typical Value = noUELinput.
Maximum voltage reference signal (VMAX). Typical Value = 1.1.
Minimum voltage reference signal (VMIN). Typical Value = 0.9.
Maximum voltage regulator output (VRMAX). Typical Value = 5.
Minimum voltage regulator output (VRMIN). Typical Value = -4.5.
Modified IEEE Type ST1 Excitation System with semi-continuous and acting terminal voltage limiter.
Modified IEEE Type ST1 Excitation System with semi-continuous and acting terminal voltage limiter.
Reference to the superclass object.
Saturation parameter (E1).
Saturation parameter (E2).
Gain (KA).
Gain (KC).
Gain (KD).
Gain (KE).
Gain (KF).
Saturation parameter (SE(E1)).
Saturation parameter (SE(E2)).
Time constant (T1).
Time constant (T2).
Time constant (T3).
Time constant (T4).
Time constant (T5).
Time constant (T6).
Time constant (TE).
Time constant (TF).
Limiter (VRMAX).
Limiter (VRMIN).
Proportional/Integral Regulator Excitation System Model.
Proportional/Integral Regulator Excitation System Model. This model can be used to represent excitation systems with a proportional-integral (PI) voltage regulator controller.
Reference to the superclass object.
Field voltage value 1 (E1). Typical Value = 0.
Field voltage value 2 (E2). Typical Value = 0.
Exciter maximum limit (Efdmax). Typical Value = 8.
Exciter minimum limit (Efdmin). Typical Value = -0.87.
PI controller gain (Ka). Typical Value = 3.15.
Exciter regulation factor (Kc). Typical Value = 0.08.
Exciter constant (Ke). Typical Value = 0.
Rate feedback gain (Kf). Typical Value = 0.
Current source gain (Ki). Typical Value = 0.
Potential source gain (Kp). Typical Value = 6.5.
Saturation factor at E1 (Se1). Typical Value = 0.
Saturation factor at E2 (Se2). Typical Value = 0.
PI controller time constant (Ta1). Typical Value = 1.
Voltage regulator time constant (Ta2). Typical Value = 0.01.
Lead time constant (Ta3). Typical Value = 0.
Lag time constant (Ta4). Typical Value = 0.
Exciter time constant (Te). Typical Value = 0.
Rate feedback time constant (Tf1). Typical Value = 0.
Rate feedback lag time constant (Tf2). Typical Value = 0.
PI maximum limit (Vr1). Typical Value = 1.
PI minimum limit (Vr2). Typical Value = -0.87.
Voltage regulator maximum limit (Vrmax). Typical Value = 1.
Voltage regulator minimum limit (Vrmin). Typical Value = -0.87.
General Purpose Rotating Excitation System Model.
General Purpose Rotating Excitation System Model. This model can be used to represent a wide range of excitation systems whose DC power source is an AC or DC generator. It encompasses IEEE type AC1, AC2, DC1, and DC2 excitation system models.
Reference to the superclass object.
Field voltage value 1 (E1). Typical Value = 3.
Field voltage value 2 (E2). Typical Value = 4.
Rate feedback signal flag (Fbf). Typical Value = fieldCurrent.
Limit type flag (Flimf). Typical Value = 0.
Rectifier regulation factor (Kc). Typical Value = 0.05.
Exciter regulation factor (Kd). Typical Value = 2.
Exciter field proportional constant (Ke). Typical Value = 1.
Field voltage feedback gain (Kefd). Typical Value = 0.
Rate feedback gain (Kf). Typical Value = 0.05.
Field voltage controller feedback gain (Kh). Typical Value = 0.
Field Current Regulator Integral Gain (Kii). Typical Value = 0.
Field Current Regulator Proportional Gain (Kip). Typical Value = 1.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Voltage Regulator Integral Gain (Kvi). Typical Value = 0.
Voltage Regulator Proportional Gain (Kvp). Typical Value = 2800.
V/Hz limiter gain (Kvphz). Typical Value = 0.
Pickup speed of V/Hz limiter (Nvphz). Typical Value = 0.
Saturation factor at E1 (Se1). Typical Value = 0.0001.
Saturation factor at E2 (Se2). Typical Value = 0.001.
Voltage Regulator time constant (Ta). Typical Value = 0.01.
Lag time constant (Tb1). Typical Value = 0.
Lag time constant (Tb2). Typical Value = 0.
Lead time constant (Tc1). Typical Value = 0.
Lead time constant (Tc2). Typical Value = 0.
Exciter field time constant (Te). Typical Value = 1.2.
Rate feedback time constant (Tf). Typical Value = 1.
Feedback lead time constant (Tf1). Typical Value = 0.
Feedback lag time constant (Tf2). Typical Value = 0.
Field current Bridge time constant (Tp). Typical Value = 0.
Maximum compounding voltage (Vcmax). Typical Value = 0.
Maximum Exciter Field Current (Vfmax). Typical Value = 47.
Minimum Exciter Field Current (Vfmin). Typical Value = -20.
Voltage Regulator Input Limit (Vimax). Typical Value = 0.1.
Maximum controller output (Vrmax). Typical Value = 47.
Minimum controller output (Vrmin). Typical Value = -20.
Exciter compounding reactance (Xc). Typical Value = 0.
Simple excitation system model representing generic characteristics of many excitation systems; intended for use where negative field current may be a problem.
Simple excitation system model representing generic characteristics of many excitation systems; intended for use where negative field current may be a problem.
Reference to the superclass object.
Power source switch (Cswitch). true = fixed voltage of 1.0 PU false = generator terminal voltage.
Maximum field voltage output (Emax). Typical Value = 5.
Minimum field voltage output (Emin). Typical Value = 0.
Gain (K) (>0). Typical Value = 200.
Rc/Rfd - ratio of field discharge resistance to field winding resistance (RcRfd). Typical Value = 0.
Ta/Tb - gain reduction ratio of lag-lead element (TaTb). The parameter Ta is not defined explicitly. Typical Value = 0.1.
Denominator time constant of lag-lead block (Tb). Typical Value = 10.
Time constant of gain block (Te) (>0). Typical Value = 0.02.
Simplified Excitation System Model.
Simplified Excitation System Model.
Reference to the superclass object.
Field voltage clipping maximum limit (Efdmax). Typical Value = 5.
Field voltage clipping minimum limit (Efdmin). Typical Value = -5.
Maximum field voltage output (Emax). Typical Value = 5.
Minimum field voltage output (Emin). Typical Value = -5.
Gain (K) (>0). Typical Value = 100.
PI controller gain (Kc). Typical Value = 0.08.
Ta/Tb - gain reduction ratio of lag-lead element (TaTb). Typical Value = 0.1.
Denominator time constant of lag-lead block (Tb). Typical Value = 10.
PI controller phase lead time constant (Tc). Typical Value = 0.
Time constant of gain block (Te). Typical Value = 0.05.
Slovakian Excitation System Model.
Slovakian Excitation System Model. UEL and secondary voltage control are included in this model. When this model is used, there cannot be a separate underexcitation limiter or VAr controller model.
Reference to the superclass object.
Field voltage clipping limit (Efdmax).
Field voltage clipping limit (Efdmin).
Maximum field voltage output (Emax). Typical Value = 20.
Minimum field voltage output (Emin). Typical Value = -20.
Gain (K). Typical Value = 1.
Parameter of underexcitation limit (K1). Typical Value = 0.1364.
Parameter of underexcitation limit (K2). Typical Value = -0.3861.
PI controller gain (Kc). Typical Value = 70.
Rectifier regulation factor (Kce). Typical Value = 0.
Exciter internal reactance (Kd). Typical Value = 0.
P controller gain (Kgob). Typical Value = 10.
PI controller gain (Kp). Typical Value = 1.
PI controller gain of integral component (Kqi). Typical Value = 0.
Rate of rise of the reactive power (Kqob).
PI controller gain (Kqp). Typical Value = 0.
Dead band of reactive power (nq). Determines the range of sensitivity. Typical Value = 0.001.
Secondary voltage control state (Qc_on_off). true = secondary voltage control is ON false = secondary voltage control is OFF. Typical Value = false.
Desired value (setpoint) of reactive power, manual setting (Qz).
Selector to apply automatic calculation in secondary controller model. true = automatic calculation is activated false = manual set is active; the use of desired value of reactive power (Qz) is required. Typical Value = true.
Apparent power of the unit (Sbase). Unit = MVA. Typical Value = 259.
PI controller phase lead time constant (Tc). Typical Value = 8.
Time constant of gain block (Te). Typical Value = 0.1.
PI controller phase lead time constant (Ti). Typical Value = 2.
Time constant (Tp). Typical Value = 0.1.
Voltage transducer time constant (Tr). Typical Value = 0.01.
Maximum error (Uimax). Typical Value = 10.
Minimum error (UImin). Typical Value = -10.
Maximum controller output (URmax). Typical Value = 10.
Minimum controller output (URmin). Typical Value = -10.
Maximum terminal voltage input (Vtmax). Determines the range of voltage dead band. Typical Value = 1.05.
Minimum terminal voltage input (Vtmin). Determines the range of voltage dead band. Typical Value = 0.95.
Maximum output (Yp). Minimum output = 0. Typical Value = 1.
Modification of an old IEEE ST1A static excitation system without overexcitation limiter (OEL) and underexcitation limiter (UEL).
Modification of an old IEEE ST1A static excitation system without overexcitation limiter (OEL) and underexcitation limiter (UEL).
Reference to the superclass object.
Exciter output current limit reference (Ilr). Typical Value = 0.
Voltage regulator gain (Ka). Typical Value = 190.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.05.
Excitation control system stabilizer gains (Kf). Typical Value = 0.
Exciter output current limiter gain (Klr). Typical Value = 0.
Voltage regulator time constant (Ta). Typical Value = 0.02.
Voltage regulator time constant (Tb). Typical Value = 10.
Voltage regulator time constant (Tb1). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 1.
Voltage regulator time constant (Tc1). Typical Value = 0.
Excitation control system stabilizer time constant (Tf). Typical Value = 1.
Maximum voltage regulator output (Vamax). Typical Value = 999.
Minimum voltage regulator output (Vamin). Typical Value = -999.
Maximum voltage regulator input limit (Vimax). Typical Value = 999.
Minimum voltage regulator input limit (Vimin). Typical Value = -999.
Maximum voltage regulator outputs (Vrmax). Typical Value = 7.8.
Minimum voltage regulator outputs (Vrmin). Typical Value = -6.7.
Excitation xfmr effective reactance (Xe). Typical Value = 0.04.
Modified IEEE ST2A static excitation system - another lead-lag block added to match the model defined by WECC.
Modified IEEE ST2A static excitation system - another lead-lag block added to match the model defined by WECC.
Reference to the superclass object.
Maximum field voltage (Efdmax). Typical Value = 99.
Voltage regulator gain (Ka). Typical Value = 120.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 1.82.
Exciter constant related to self-excited field (Ke). Typical Value = 1.
Excitation control system stabilizer gains (Kf). Typical Value = 0.05.
Potential circuit gain coefficient (Ki). Typical Value = 8.
Potential circuit gain coefficient (Kp). Typical Value = 4.88.
Voltage regulator time constant (Ta). Typical Value = 0.15.
Voltage regulator time constant (Tb). Typical Value = 0.
Voltage regulator time constant (Tc). Typical Value = 0.
Exciter time constant, integration rate associated with exciter control (Te). Typical Value = 0.5.
Excitation control system stabilizer time constant (Tf). Typical Value = 0.7.
UEL input (UELin). true = HV gate false = add to error signal. Typical Value = false.
Maximum voltage regulator outputs (Vrmax). Typical Value = 1.
Minimum voltage regulator outputs (Vrmin). Typical Value = -1.
Modified IEEE ST3A static excitation system with added speed multiplier.
Modified IEEE ST3A static excitation system with added speed multiplier.
Reference to the superclass object.
Maximum AVR output (Efdmax). Typical Value = 6.9.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 1.1.
Feedback gain constant of the inner loop field regulator (Kg). Typical Value = 1.
Potential circuit gain coefficient (Ki). Typical Value = 4.83.
AVR gain (Kj). Typical Value = 200.
Forward gain constant of the inner loop field regulator (Km). Typical Value = 7.04.
Potential source gain (Kp) (>0). Typical Value = 4.37.
Coefficient to allow different usage of the model-speed coefficient (Ks). Typical Value = 0.
Coefficient to allow different usage of the model-speed coefficient (Ks1). Typical Value = 0.
Voltage regulator time constant (Tb). Typical Value = 6.67.
Voltage regulator time constant (Tc). Typical Value = 1.
Potential circuit phase angle (thetap). Typical Value = 20.
Forward time constant of inner loop field regulator (Tm). Typical Value = 1.
Maximum excitation voltage (Vbmax). Typical Value = 8.63.
Maximum inner loop feedback voltage (Vgmax). Typical Value = 6.53.
Maximum voltage regulator input limit (Vimax). Typical Value = 0.2.
Minimum voltage regulator input limit (Vimin). Typical Value = -0.2.
Maximum voltage regulator output (Vrmax). Typical Value = 1.
Minimum voltage regulator output (Vrmin). Typical Value = 0.
Reactance associated with potential source (Xl). Typical Value = 0.09.
Modified IEEE ST4B static excitation system with maximum inner loop feedback gain Vgmax.
Modified IEEE ST4B static excitation system with maximum inner loop feedback gain Vgmax.
Reference to the superclass object.
Rectifier loading factor proportional to commutating reactance (Kc). Typical Value = 0.113.
Feedback gain constant of the inner loop field regulator (Kg). Typical Value = 0.
Potential circuit gain coefficient (Ki). Typical Value = 0.
Voltage regulator integral gain output (Kim). Typical Value = 0.
Voltage regulator integral gain (Kir). Typical Value = 10.75.
Potential circuit gain coefficient (Kp). Typical Value = 9.3.
Voltage regulator proportional gain output (Kpm). Typical Value = 1.
Voltage regulator proportional gain (Kpr). Typical Value = 10.75.
Selector (LVgate). true = LVgate is part of the block diagram false = LVgate is not part of the block diagram. Typical Value = false.
Voltage regulator time constant (Ta). Typical Value = 0.02.
Potential circuit phase angle (thetap). Typical Value = 0.
Selector (Uel). true = UEL is part of block diagram false = UEL is not part of block diagram. Typical Value = false.
Maximum excitation voltage (Vbmax). Typical Value = 11.63.
Maximum inner loop feedback voltage (Vgmax). Typical Value = 5.8.
Maximum inner loop output (Vmmax). Typical Value = 99.
Minimum inner loop output (Vmmin). Typical Value = -99.
Maximum voltage regulator output (Vrmax). Typical Value = 1.
Minimum voltage regulator output (Vrmin). Typical Value = -0.87.
Reactance associated with potential source (Xl). Typical Value = 0.124.
Modified IEEE ST6B static excitation system with PID controller and optional inner feedbacks loop.
Modified IEEE ST6B static excitation system with PID controller and optional inner feedbacks loop.
Reference to the superclass object.
Exciter output current limit reference (Ilr). Typical Value = 4.164.
Selector (K1). true = feedback is from Ifd false = feedback is not from Ifd. Typical Value = true.
Exciter output current limit adjustment (Kcl). Typical Value = 1.0577.
Pre-control gain constant of the inner loop field regulator (Kff). Typical Value = 1.
Feedback gain constant of the inner loop field regulator (Kg). Typical Value = 1.
Voltage regulator integral gain (Kia). Typical Value = 45.094.
Exciter output current limit adjustment (Kcl). Typical Value = 17.33.
Forward gain constant of the inner loop field regulator (Km). Typical Value = 1.
Voltage regulator proportional gain (Kpa). Typical Value = 18.038.
Voltage regulator derivative gain (Kvd). Typical Value = 0.
OEL input selector (OELin). Typical Value = noOELinput.
Feedback time constant of inner loop field voltage regulator (Tg). Typical Value = 0.02.
Rectifier firing time constant (Ts). Typical Value = 0.
Voltage regulator derivative gain (Tvd). Typical Value = 0.
Maximum voltage regulator output (Vamax). Typical Value = 4.81.
Minimum voltage regulator output (Vamin). Typical Value = -3.85.
Selector (Vilim). true = Vimin-Vimax limiter is active false = Vimin-Vimax limiter is not active. Typical Value = true.
Maximum voltage regulator input limit (Vimax). Typical Value = 10.
Minimum voltage regulator input limit (Vimin). Typical Value = -10.
Selector (Vmult). true = multiply regulator output by terminal voltage false = do not multiply regulator output by terminal voltage. Typical Value = true.
Maximum voltage regulator output (Vrmax). Typical Value = 4.81.
Minimum voltage regulator output (Vrmin). Typical Value = -3.85.
Excitation source reactance (Xc). Typical Value = 0.05.
Modified IEEE ST7B static excitation system without stator current limiter (SCL) and current compensator (DROOP) inputs.
Modified IEEE ST7B static excitation system without stator current limiter (SCL) and current compensator (DROOP) inputs.
Reference to the superclass object.
High-value gate feedback gain (Kh). Typical Value = 1.
Voltage regulator integral gain (Kia). Typical Value = 1.
Low-value gate feedback gain (Kl). Typical Value = 1.
Voltage regulator proportional gain (Kpa). Typical Value = 40.
OEL input selector (OELin). Typical Value = noOELinput.
Regulator lag time constant (Tb). Typical Value = 1.
Regulator lead time constant (Tc). Typical Value = 1.
Excitation control system stabilizer time constant (Tf). Typical Value = 1.
Feedback time constant of inner loop field voltage regulator (Tg). Typical Value = 1.
Feedback time constant (Tia). Typical Value = 3.
Rectifier firing time constant (Ts). Typical Value = 0.
UEL input selector (UELin). Typical Value = noUELinput.
Maximum voltage reference signal (Vmax). Typical Value = 1.1.
Minimum voltage reference signal (Vmin). Typical Value = 0.9.
Maximum voltage regulator output (Vrmax). Typical Value = 5.
Minimum voltage regulator output (Vrmin). Typical Value = -4.5.
Excitation system function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Excitation system function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Discontinuous excitation control model associated with this excitation system model.
Overexcitation limiter model associated with this excitation system model.
Power Factor or VAr controller Type I model associated with this excitation system model.
Power Factor or VAr controller Type II model associated with this excitation system model.
Power system stabilizer model associated with this excitation system model.
Synchronous machine model with which this excitation system model is associated.
Undrexcitation limiter model associated with this excitation system model.
Voltage compensator model associated with this excitation system model.
Excitation system function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Excitation system function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Model Expected Energy from Market Clearing, interval based
Model Expected Energy from Market Clearing, interval based
Reference to the superclass object.
undocumented
undocumented
undocumented
Model Expected Energy from Market Clearing
Model Expected Energy from Market Clearing
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
A type of customer agreement involving an external agency.
A type of customer agreement involving an external agency. For example, a customer may form a contracts with an Energy Service Supplier if Direct Access is permitted.
Reference to the superclass object.
This class represents external network and it is used for IEC 60909 calculations.
This class represents external network and it is used for IEC 60909 calculations.
Reference to the superclass object.
Power Frequency Bias. This is the change in power injection divided by the change in frequency and negated. A positive value of the power frequency bias provides additional power injection upon a drop in frequency.
Indicates whether initial symmetrical short-circuit current and power have been calculated according to IEC (Ik").
Maximum initial symmetrical short-circuit currents (Ik" max) in A (Ik" = Sk"/(SQRT(3) Un)). Used for short circuit data exchange according to IEC 60909
Maximum active power of the injection.
Not for short circuit modelling; It is used for modelling of infeed for load flow exchange. If maxQ and minQ are not used ReactiveCapabilityCurve can be used
Maximum ratio of zero sequence resistance of Network Feeder to its zero sequence reactance (R(0)/X(0) max). Used for short circuit data exchange according to IEC 60909
Maximum ratio of positive sequence resistance of Network Feeder to its positive sequence reactance (R(1)/X(1) max). Used for short circuit data exchange according to IEC 60909
Maximum ratio of zero sequence impedance to its positive sequence impedance (Z(0)/Z(1) max). Used for short circuit data exchange according to IEC 60909
Minimum initial symmetrical short-circuit currents (Ik" min) in A (Ik" = Sk"/(SQRT(3) Un)). Used for short circuit data exchange according to IEC 60909
Minimum active power of the injection.
Not for short circuit modelling; It is used for modelling of infeed for load flow exchange. If maxQ and minQ are not used ReactiveCapabilityCurve can be used
Indicates whether initial symmetrical short-circuit current and power have been calculated according to IEC (Ik"). Used for short circuit data exchange according to IEC 6090
Minimum ratio of positive sequence resistance of Network Feeder to its positive sequence reactance (R(1)/X(1) min). Used for short circuit data exchange according to IEC 60909
Minimum ratio of zero sequence impedance to its positive sequence impedance (Z(0)/Z(1) min). Used for short circuit data exchange according to IEC 60909
Active power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Reactive power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Priority of unit for use as powerflow voltage phase angle reference bus selection. 0 = don t care (default) 1 = highest priority. 2 is less than 1 and so on.
Voltage factor in pu, which was used to calculate short-circuit current Ik" and power Sk".
FACTS device asset.
FACTS device asset.
Reference to the superclass object.
Kind of FACTS device.
Financial Transmission Rights (FTR) regarding transmission capacity at a flowgate.
Financial Transmission Rights (FTR) regarding transmission capacity at a flowgate.
Reference to the superclass object.
Buy, Sell
Quantity, typically MWs - Seller owns all rights being offered, MWs over time on same Point of Receipt, Point of Delivery, or Resource.
Type of rights being offered (product) allowed to be auctioned (option, obligation).
Fixed (covers re-configuration, grandfathering) or Optimized (up for sale/purchase
undocumented
undocumented
undocumented
Peak, Off-peak, 24-hour
A facility may contain buildings, storage facilities, switching facilities, power generation, manufacturing facilities, maintenance facilities, etc.
A facility may contain buildings, storage facilities, switching facilities, power generation, manufacturing facilities, maintenance facilities, etc.
Reference to the superclass object.
Kind of this facility.
An event where an asset has failed to perform its functions within specified parameters.
An event where an asset has failed to perform its functions within specified parameters.
Reference to the superclass object.
Code for asset failure.
How the asset failure was isolated from the system.
The method used for locating the faulted part of the asset. For example, cable options include: Cap Discharge-Thumping, Bridge Method, Visual Inspection, Other.
Failure location on an object.
Abnormal condition causing current flow through conducting equipment, such as caused by equipment failure or short circuits from objects not typically modeled (for example, a tree falling on a line).
Abnormal condition causing current flow through conducting equipment, such as caused by equipment failure or short circuits from objects not typically modeled (for example, a tree falling on a line).
Reference to the superclass object.
Fault impedance. Its usage is described by 'kind'.
The kind of phase fault.
The phases participating in the fault. The fault connections into these phases are further specified by the type of fault.
All types of fault cause.
Equipment carrying this fault.
Outage associated with this fault.
Type of cause of the fault.
Type of cause of the fault.
Reference to the superclass object.
Impedance description for the fault.
Impedance description for the fault.
Reference to the superclass object.
The resistance of the fault between phases and ground.
The resistance of the fault between phases.
The reactance of the fault between phases and ground.
The reactance of the fault between phases.
A FaultIndicator is typically only an indicator (which may or may not be remotely monitored), and not a piece of equipment that actually initiates a protection event.
A FaultIndicator is typically only an indicator (which may or may not be remotely monitored), and not a piece of equipment that actually initiates a protection event. It is used for FLISR (Fault Location, Isolation and Restoration) purposes, assisting with the dispatch of crews to "most likely" part of the network (i.e. assists with determining circuit section where the fault most likely happened).
Reference to the superclass object.
Parameters of fault indicator asset.
Parameters of fault indicator asset.
Reference to the superclass object.
Kind of reset mechanisim of this fault indicator.
Various current financial properties associated with a particular asset.
Various current financial properties associated with a particular asset. Historical properties may be determined by ActivityRecords associated with the asset.
Reference to the superclass object.
The account to which this actual material item is charged.
The actual purchase cost of this particular asset.
Description of the cost.
Type of cost to which this Material Item belongs.
Value of asset as of 'valueDateTime'.
Date and time asset's financial value was put in plant for regulatory accounting purposes (e.g., for rate base calculations). This is sometime referred to as the "in-service date".
Date and time asset was purchased.
Purchase order identifier.
The quantity of the asset if per unit length, for example conductor.
Date and time at which the financial value was last established.
Date and time warranty on asset expires.
undocumented
Models 5-Minutes Auxillary Data
Models 5-Minutes Auxillary Data
Reference to the superclass object.
undocumented
undocumented
undocumented
Quantity with float value and associated unit information.
Quantity with float value and associated unit information.
Reference to the superclass object.
undocumented
undocumented
undocumented
The coded identification of the direction of energy flow.
The coded identification of the direction of energy flow.
Reference to the superclass object.
The coded identification of the direction of energy flow.
A flowgate, is single or group of transmission elements intended to model MW flow impact relating to transmission limitations and transmission service usage.
A flowgate, is single or group of transmission elements intended to model MW flow impact relating to transmission limitations and transmission service usage.
Reference to the superclass object.
The direction of the flowgate, export or import
end effective date
Export MW rating
Import MW rating
start effective date
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
Flowgate defined partner
Flowgate defined partner
Reference to the superclass object.
undocumented
IDC (Interchange Distribution Calulator) sends data for a TLR (Transmission Loading Relief).
IDC (Interchange Distribution Calulator) sends data for a TLR (Transmission Loading Relief).
Reference to the superclass object.
Date/Time when record becomes effective Used to determine when a record becomes effective.
Energy Flow level that should be maintained according to the TLR rules as specified by the IDC. For Realtime Markets use in dispatch to control constraints under TLR and calculate unconstrained market flows
Date/Time when record is no longer effective Used to determine when a record is no longer effective
undocumented
Day Ahead, Network Native Load, Economic Dispatch, values used for calculation of Network Native Load (NNL) Determinator process.
Day Ahead, Network Native Load, Economic Dispatch, values used for calculation of Network Native Load (NNL) Determinator process.
Reference to the superclass object.
Limit for Economic Dispatch priority 6 energy flow on the specified flowgate for the specified time period.
Date/Time when record becomes effective Used to determine when a record becomes effective
Limit for firm flow on the specified flowgate for the specified time period. The amount of energy flow over a specifed flowgate due to generation in the market which can be classified as Firm Network priority.
Specifies the direction of energy flow in the flowgate
The amount of energy flow over a specifed flowgate due to generation in the market.
Net Energy flow in flowgate for the associated FlowgatePartner
undocumented
undocumented
Forbbiden region is operating ranges where the units are unable to maintain steady operation without causing equipment damage.
Forbbiden region is operating ranges where the units are unable to maintain steady operation without causing equipment damage. The four attributes that define a forbidden region are the low MW, the High MW, the crossing time, and the crossing cost.
Reference to the superclass object.
Time to cross the forbidden region in minutes.
Cost associated with crossing the forbidden region
High end of the region definition
Low end of the region definition.
Used to indicate former references to the same piece of equipment.
Used to indicate former references to the same piece of equipment. The ID, name, and effectivity dates are utilized.
Reference to the superclass object.
undocumented
The fossil fuel consumed by the non-nuclear thermal generating unit.
The fossil fuel consumed by the non-nuclear thermal generating unit. For example, coal, oil, gas, etc. This a the specific fuels that the generating unit can consume.
Reference to the superclass object.
The type of fossil fuel, such as coal, oil, or gas.
The cost in terms of heat value for the given type of fuel.
The cost of fuel used for economic dispatching which includes: fuel cost, transportation cost, and incremental maintenance cost.
The efficiency factor for the fuel (per unit) in terms of the effective energy absorbed.
Handling and processing cost associated with this fuel.
The amount of heat per weight (or volume) of the given type of fuel.
Relative amount of the given type of fuel, when multiple fuels are being consumed.
The fuel's fraction of pollution credit per unit of heat content.
The active power output level of the unit at which the given type of fuel is switched on. This fuel (e.g., oil) is sometimes used to supplement the base fuel (e.g., coal) at high active power output levels.
The active power output level of the unit at which the given type of fuel is switched off. This fuel (e.g., oil) is sometimes used to stabilize the base fuel (e.g., coal) at low active power output levels.
A thermal generating unit may have one or more fossil fuels.
Fossil fueled boiler (e.g., coal, oil, gas).
Fossil fueled boiler (e.g., coal, oil, gas).
Reference to the superclass object.
Off nominal frequency effect on auxiliary real power. Per unit active power variation versus per unit frequency variation.
Off nominal voltage effect on auxiliary real power. Per unit active power variation versus per unit voltage variation.
The control mode of the boiler.
Active power error bias ratio.
Integral constant.
Proportional constant.
Pressure error bias ratio.
Pressure error deadband.
Time constant.
Feedwater integral gain ratio.
Feedwater proportional gain ratio.
Feedwater time constant rato.
Fuel demand limit.
Fuel delay.
Fuel supply time constant.
Active power maximum error rate limit.
Mechanical power sensor lag.
Active power minimum error rate limit.
Pressure control derivative gain ratio.
Pressure control integral gain ratio.
Pressure control proportional gain ratio.
Pressure feedback indicator.
Drum/primary superheater capacity.
Secondary superheater capacity.
Superheater pipe pressure drop constant.
Throttle pressure setpoint.
A device to convert from one frequency to another (e.g., frequency F1 to F2) comprises a pair of FrequencyConverter instances.
A device to convert from one frequency to another (e.g., frequency F1 to F2) comprises a pair of FrequencyConverter instances. One converts from F1 to DC, the other converts the DC to F2.
Reference to the superclass object.
Frequency on the AC side.
The maximum active power on the DC side at which the frequence converter should operate.
The maximum voltage on the DC side at which the frequency converter should operate.
The minimum active power on the DC side at which the frequence converter should operate.
The minimum voltage on the DC side at which the frequency converter should operate.
The amount of fuel of a given type which is allocated for consumption over a specified period of time.
The amount of fuel of a given type which is allocated for consumption over a specified period of time.
Reference to the superclass object.
The end time and date of the fuel allocation schedule.
The start time and date of the fuel allocation schedule.
The type of fuel, which also indicates the corresponding measurement unit.
The maximum amount fuel that is allocated for consumption for the scheduled time period.
The minimum amount fuel that is allocated for consumption for the scheduled time period, e.g., based on a "take-or-pay" contract.
A fuel allocation schedule must have a fossil fuel.
A thermal generating unit may have one or more fuel allocation schedules.
Relationship between unit fuel cost in $/kWh(Y-axis) and unit output in MW (X-axis).
Relationship between unit fuel cost in $/kWh(Y-axis) and unit output in MW (X-axis).
Reference to the superclass object.
undocumented
Indication of region for fuel inventory purposes
Indication of region for fuel inventory purposes
Reference to the superclass object.
end effective date
The type of fuel region
Time of last update
start effective date
undocumented
undocumented
undocumented
An overcurrent protective device with a circuit opening fusible part that is heated and severed by the passage of overcurrent through it.
An overcurrent protective device with a circuit opening fusible part that is heated and severed by the passage of overcurrent through it. A fuse is considered a switching device because it breaks current.
Reference to the superclass object.
Price of gas in monetary units
Price of gas in monetary units
Reference to the superclass object.
The average natural gas price at a defined fuel region.
undocumented
Logical gate than support logical operation based on the input.
Logical gate than support logical operation based on the input.
Reference to the superclass object.
The logical operation of the gate.
Input pin for a logical gate.
Input pin for a logical gate. The condition described in the input pin will give a logical true or false. Result from measurement and calculation are converted to a true or false.
Reference to the superclass object.
The compare operation.
If true, use the absolute value for compare..
The duration the compare condition need to be present before given a true. Default is 0 seconds.
Invert/negate the result of the compare.
The threshold percentage that should be used for compare with the percentage change between input value and threshold value.
The threshold value that should be used for compare with the input value.
undocumented
This class models the generation distribution factors.
This class models the generation distribution factors. This class needs to be used along with the AggregatedPnode and the IndividualPnode to show the distriubtion of each individual party.
Reference to the superclass object.
Used to calculate generation "participation" of an individual pnond in an AggregatePnode.
undocumented
undocumented
This class provides the resistive and reactive components of compensation for the generator associated with the IEEE Type 2 voltage compensator for current flow out of one of the other generators in the interconnection.
This class provides the resistive and reactive components of compensation for the generator associated with the IEEE Type 2 voltage compensator for current flow out of one of the other generators in the interconnection.
Reference to the superclass object.
<font color="#0f0f0f">Resistive component of compensation of generator associated with this IEEE Type 2 voltage compensator for current flow out of another generator (Rcij).</font>
<font color="#0f0f0f">Reactive component of compensation of generator associated with this IEEE Type 2 voltage compensator for current flow out of another generator (Xcij).</font>
Standard synchronous machine out of which current flow is being compensated for.
The standard IEEE Type 2 voltage compensator of this compensation.
Relationship between unit operating cost (Y-axis) and unit output active power (X-axis).
Relationship between unit operating cost (Y-axis) and unit output active power (X-axis). The operating cost curve for thermal units is derived from heat input and fuel costs. The operating cost curve for hydro units is derived from water flow rates and equivalent water costs.
Reference to the superclass object.
Flag is set to true when output is expressed in net active power.
A generating unit may have one or more cost curves, depending upon fuel mixture and fuel cost.
The generating unit's Operator-approved current operating schedule (or plan), typically produced with the aid of unit commitment type analyses.
The generating unit's Operator-approved current operating schedule (or plan), typically produced with the aid of unit commitment type analyses. The X-axis represents absolute time. The Y1-axis represents the status (0=off-line and unavailable: 1=available: 2=must run: 3=must run at fixed power value: etc.). The Y2-axis represents the must run fixed power value where required.
Reference to the superclass object.
A generating unit may have an operating schedule, indicating the planned operation of the unit.
Model of clearing result of the market run at the market level.
Model of clearing result of the market run at the market level. Identifies interval
Reference to the superclass object.
Provides the adjusted load forecast value on a load forecast zone basis.
Provides the adjusted load forecast value on a load forecast zone basis.
Reference to the superclass object.
Load Prediction/Forecast (MW), by Time Period (5', 10', 15')
Amount of load in the control zone Attribute Usage: hourly load value for the specific area
Amount of interchange for the control zone Attribute Usage: hourly interchange value for the specific area
undocumented
undocumented
Offer to supply energy/ancillary services from a generating unit or resource
Offer to supply energy/ancillary services from a generating unit or resource
Reference to the superclass object.
Will indicate if the unit is part of a CC offer or not
Maximum down time.
Installed Capacity value
Maximum Dn ramp rate in MW/min
Power rating available for unit under emergency conditions greater than or equal to maximum economic limit.
Maximum high economic MW limit, that should not exceed the maximum operating MW limit
Minimum power rating for unit under emergency conditions, which is less than or equal to the economic minimum.
Low economic MW limit that shall be greater than or equal to the minimum operating MW limit
Resource fixed no load cost.
Time required for crew notification prior to start up of the unit.
Bid operating mode ('C' - cycling, 'F' - fixed, 'M' - must run, 'U' - unavailable)
Maximum Up ramp rate in MW/min
Ramp curve type: 0 - Fixed ramp rate independent of rate function unit MW output 1 - Static ramp rates as a function of unit MW output only 2 - Dynamic ramp rates as a function of unit MW output and ramping time
Resource startup ramp rate (MW/minute)
Resource startup type: 1 - Fixed startup time and fixed startup cost 2 - Startup time as a function of down time and fixed startup cost 3 - Startup cost as a function of down time
Startup cost/price
Maximum up time.
undocumented
undocumented
undocumented
undocumented
undocumented
A single or set of synchronous machines for converting mechanical power into alternating-current power.
A single or set of synchronous machines for converting mechanical power into alternating-current power. For example, individual machines within a set may be defined for scheduling purposes while a single control signal is derived for the set. In this case there would be a GeneratingUnit for each member of the set and an additional GeneratingUnit corresponding to the set.
Reference to the superclass object.
The planned unused capacity (spinning reserve) which can be used to support emergency load.
The planned unused capacity which can be used to support automatic control overruns.
For dispatchable units, this value represents the economic active power basepoint, for units that are not dispatchable, this value represents the fixed generation value. The value must be between the operating low and high limits.
Unit control error deadband. When a unit's desired active power change is less than this deadband, then no control pulses will be sent to the unit.
Pulse high limit which is the largest control pulse that the unit can respond to.
Pulse low limit which is the smallest control pulse that the unit can respond to.
Unit response rate which specifies the active power change for a control pulse of one second in the most responsive loading level of the unit.
The efficiency of the unit in converting mechanical energy, from the prime mover, into electrical energy.
The unit control mode.
The source of controls for a generating unit.
Governor motor position limit.
Governor Speed Changer Droop. This is the change in generator power output divided by the change in frequency normalized by the nominal power of the generator and the nominal frequency and expressed in percent and negated. A positive value of speed change droop provides additional generator output upon a drop in frequency.
High limit for secondary (AGC) control.
Default initial active power which is used to store a powerflow result for the initial active power for this unit in this network configuration.
Generating unit long term economic participation factor.
Low limit for secondary (AGC) control.
The normal maximum rate the generating unit active power output can be lowered by control actions.
Maximum high economic active power limit, that should not exceed the maximum operating active power limit.
This is the maximum operating active power limit the dispatcher can enter for this unit.
Maximum allowable spinning reserve. Spinning reserve will never be considered greater than this value regardless of the current operating point.
Low economic active power limit that must be greater than or equal to the minimum operating active power limit.
This is the minimum operating active power limit the dispatcher can enter for this unit.
Minimum time interval between unit shutdown and startup.
Detail level of the generator model data.
The nominal power of the generating unit. Used to give precise meaning to percentage based attributes such as the governor speed change droop (governorSCD attribute).
Generating unit economic participation factor.
Defined as: 1 / ( 1 - Incremental Transmission Loss); with the Incremental Transmission Loss expressed as a plus or minus value. The typical range of penalty factors is (0.9 to 1.1).
The normal maximum rate the generating unit active power output can be raised by control actions.
The unit's gross rated maximum capacity (book value).
The gross rated minimum generation level which the unit can safely operate at while delivering power to the transmission grid.
The net rated maximum capacity determined by subtracting the auxiliary power used to operate the internal plant machinery from the rated gross maximum capacity.
Generating unit short term economic participation factor.
The initial startup cost incurred for each start of the GeneratingUnit.
Time it takes to get the unit on-line, from the time that the prime mover mechanical power is applied.
Generating unit economic participation factor.
The efficiency of the unit in converting the fuel into electrical energy.
The variable cost component of production per unit of ActivePower.
A generating unit may have an operating schedule, indicating the planned operation of the unit.
Optimal Power Flow or State Estimator Unit Data for Operator Training Simulator.
Optimal Power Flow or State Estimator Unit Data for Operator Training Simulator. This is used for RealTime, Study and Maintenance Users
Reference to the superclass object.
Loss Factor
Unit reactive power generation in MVAR
The maximum active power generation of the unit in MW
The minimum active power generation of the unit in MW
Unit active power generation in MW
Unit sencivity factor. The distribution factors (DFAX) for the unit
undocumented
undocumented
The energy seller in the energy marketplace.
The energy seller in the energy marketplace.
Reference to the superclass object.
Generic generation equipment that may be used for various purposes such as work planning.
Generic generation equipment that may be used for various purposes such as work planning. It defines both the Real and Reactive power properties (modelled at the PSR level as a GeneratingUnit + SynchronousMachine).
Reference to the superclass object.
Maximum real power limit.
Maximum reactive power limit.
Minimum real power generated.
Minimum reactive power generated.
Direct-axis subtransient resistance.
Direct-axis synchronous resistance.
Direct-axis transient resistance.
Quadrature-axis subtransient resistance.
Quadrature-axis synchronous resistance.
Quadrature-axis transient resistance.
Direct-axis subtransient reactance.
Direct-axis synchronous reactance.
Direct-axis transient reactance.
Quadrature-axis subtransient reactance.
Quadrature-axis synchronous reactance.
Quadrature-axis transient reactance.
An arbitrary switching step.
An arbitrary switching step.
Reference to the superclass object.
Group to which this step belongs.
Generic asset or material item that may be used for planning, work or design purposes.
Generic asset or material item that may be used for planning, work or design purposes.
Reference to the superclass object.
Estimated unit cost (or cost per unit length) of this type of asset. It does not include labor to install/construct or configure it.
The value, unit of measure, and multiplier for the quantity.
True if item is a stock item (default).
undocumented
undocumented
undocumented
Generic constraints can represent secure areas, voltage profile, transient stability and voltage collapse limits.
Generic constraints can represent secure areas, voltage profile, transient stability and voltage collapse limits. The generic constraints can be one of the following forms:
Reference to the superclass object.
Interval End Time
Interval Start Time
Maximum Limit (MW)
Minimum Limit (MW)
A geographical region of a power system network model.
A geographical region of a power system network model.
Reference to the superclass object.
General model for any prime mover with a PID governor, used primarily for combustion turbine and combined cycle units.
General model for any prime mover with a PID governor, used primarily for combustion turbine and combined cycle units. This model can be used to represent a variety of prime movers controlled by PID governors. It is suitable, for example, for representation of
Reference to the superclass object.
Acceleration limiter setpoint (Aset). Unit = PU/sec. Typical Value = 0.01.
Speed governor dead band in per unit speed (db). In the majority of applications, it is recommended that this value be set to zero. Typical Value = 0.
Speed sensitivity coefficient (Dm). Dm can represent either the variation of the engine power with the shaft speed or the variation of maximum power capability with shaft speed. If it is positive it describes the falling slope of the engine speed verses power characteristic as speed increases. A slightly falling characteristic is typical for reciprocating engines and some aero-derivative turbines. If it is negative the engine power is assumed to be unaffected by the shaft speed, but the maximum permissible fuel flow is taken to fall with falling shaft speed. This is characteristic of single-shaft industrial turbines due to exhaust temperature limits. Typical Value = 0.
Acceleration limiter gain (Ka). Typical Value = 10.
Governor derivative gain (Kdgov). Typical Value = 0.
Governor integral gain (Kigov). Typical Value = 2.
Load limiter integral gain for PI controller (Kiload). Typical Value = 0.67.
Power controller (reset) gain (Kimw). The default value of 0.01 corresponds to a reset time of 100 seconds. A value of 0.001 corresponds to a relatively slow acting load controller. Typical Value = 0.01.
Governor proportional gain (Kpgov). Typical Value = 10.
Load limiter proportional gain for PI controller (Kpload). Typical Value = 2.
Turbine gain (Kturb) (>0). Typical Value = 1.5.
Load limiter reference value (Ldref). Typical Value = 1.
Maximum value for speed error signal (maxerr). Typical Value = 0.05.
Minimum value for speed error signal (minerr). Typical Value = -0.05.
Base for power values (MWbase) (> 0). Unit = MW.
Permanent droop (R). Typical Value = 0.04.
Minimum valve closing rate (Rclose). Unit = PU/sec. Typical Value = -0.1.
Maximum rate of load limit decrease (Rdown). Typical Value = -99.
Maximum valve opening rate (Ropen). Unit = PU/sec. Typical Value = 0.10.
Feedback signal for droop (Rselect). Typical Value = electricalPower.
Maximum rate of load limit increase (Rup). Typical Value = 99.
Acceleration limiter time constant (Ta) (>0). Typical Value = 0.1.
Actuator time constant (Tact). Typical Value = 0.5.
Turbine lag time constant (Tb) (>0). Typical Value = 0.5.
Turbine lead time constant (Tc). Typical Value = 0.
Governor derivative controller time constant (Tdgov). Typical Value = 1.
Transport time delay for diesel engine used in representing diesel engines where there is a small but measurable transport delay between a change in fuel flow setting and the development of torque (Teng). Teng should be zero in all but special cases where this transport delay is of particular concern. Typical Value = 0.
Load Limiter time constant (Tfload) (>0). Typical Value = 3.
Electrical power transducer time constant (Tpelec) (>0). Typical Value = 1.
Temperature detection lead time constant (Tsa). Typical Value = 4.
Temperature detection lag time constant (Tsb). Typical Value = 5.
Maximum valve position limit (Vmax). Typical Value = 1.
Minimum valve position limit (Vmin). Typical Value = 0.15.
No load fuel flow (Wfnl). Typical Value = 0.2.
Switch for fuel source characteristic to recognize that fuel flow, for a given fuel valve stroke, can be proportional to engine speed (Wfspd). true = fuel flow proportional to speed (for some gas turbines and diesel engines with positive displacement fuel injectors) false = fuel control system keeps fuel flow independent of engine speed. Typical Value = true.
General governor model with frequency-dependent fuel flow limit.
General governor model with frequency-dependent fuel flow limit. This model is a modification of the GovCT1 model in order to represent the frequency-dependent fuel flow limit of a specific gas turbine manufacturer.
Reference to the superclass object.
Acceleration limiter setpoint (Aset). Unit = PU/sec. Typical Value = 10.
Speed governor dead band in per unit speed (db). In the majority of applications, it is recommended that this value be set to zero. Typical Value = 0.
Speed sensitivity coefficient (Dm). Dm can represent either the variation of the engine power with the shaft speed or the variation of maximum power capability with shaft speed. If it is positive it describes the falling slope of the engine speed verses power characteristic as speed increases. A slightly falling characteristic is typical for reciprocating engines and some aero-derivative turbines. If it is negative the engine power is assumed to be unaffected by the shaft speed, but the maximum permissible fuel flow is taken to fall with falling shaft speed. This is characteristic of single-shaft industrial turbines due to exhaust temperature limits. Typical Value = 0.
Frequency threshold 1 (Flim1). Unit = Hz. Typical Value = 59.
Frequency threshold 10 (Flim10). Unit = Hz. Typical Value = 0.
Frequency threshold 2 (Flim2). Unit = Hz. Typical Value = 0.
Frequency threshold 3 (Flim3). Unit = Hz. Typical Value = 0.
Frequency threshold 4 (Flim4). Unit = Hz. Typical Value = 0.
Frequency threshold 5 (Flim5). Unit = Hz. Typical Value = 0.
Frequency threshold 6 (Flim6). Unit = Hz. Typical Value = 0.
Frequency threshold 7 (Flim7). Unit = Hz. Typical Value = 0.
Frequency threshold 8 (Flim8). Unit = Hz. Typical Value = 0.
Frequency threshold 9 (Flim9). Unit = Hz. Typical Value = 0.
Acceleration limiter Gain (Ka). Typical Value = 10.
Governor derivative gain (Kdgov). Typical Value = 0.
Governor integral gain (Kigov). Typical Value = 0.45.
Load limiter integral gain for PI controller (Kiload). Typical Value = 1.
Power controller (reset) gain (Kimw). The default value of 0.01 corresponds to a reset time of 100 seconds. A value of 0.001 corresponds to a relatively slow acting load controller. Typical Value = 0.
Governor proportional gain (Kpgov). Typical Value = 4.
Load limiter proportional gain for PI controller (Kpload). Typical Value = 1.
Turbine gain (Kturb). Typical Value = 1.9168.
Load limiter reference value (Ldref). Typical Value = 1.
Maximum value for speed error signal (Maxerr). Typical Value = 1.
Minimum value for speed error signal (Minerr). Typical Value = -1.
Base for power values (MWbase) (> 0). Unit = MW.
Power limit 1 (Plim1). Typical Value = 0.8325.
Power limit 10 (Plim10). Typical Value = 0.
Power limit 2 (Plim2). Typical Value = 0.
Power limit 3 (Plim3). Typical Value = 0.
Power limit 4 (Plim4). Typical Value = 0.
Power limit 5 (Plim5). Typical Value = 0.
Power limit 6 (Plim6). Typical Value = 0.
Power limit 7 (Plim7). Typical Value = 0.
Power limit 8 (Plim8). Typical Value = 0.
Power Limit 9 (Plim9). Typical Value = 0.
Ramp rate for frequency-dependent power limit (Prate). Typical Value = 0.017.
Permanent droop (R). Typical Value = 0.05.
Minimum valve closing rate (Rclose). Unit = PU/sec. Typical Value = -99.
Maximum rate of load limit decrease (Rdown). Typical Value = -99.
Maximum valve opening rate (Ropen). Unit = PU/sec. Typical Value = 99.
Feedback signal for droop (Rselect). Typical Value = electricalPower.
Maximum rate of load limit increase (Rup). Typical Value = 99.
Acceleration limiter time constant (Ta). Typical Value = 1.
Actuator time constant (Tact). Typical Value = 0.4.
Turbine lag time constant (Tb). Typical Value = 0.1.
Turbine lead time constant (Tc). Typical Value = 0.
Governor derivative controller time constant (Tdgov). Typical Value = 1.
Transport time delay for diesel engine used in representing diesel engines where there is a small but measurable transport delay between a change in fuel flow setting and the development of torque (Teng). Teng should be zero in all but special cases where this transport delay is of particular concern. Typical Value = 0.
Load Limiter time constant (Tfload). Typical Value = 3.
Electrical power transducer time constant (Tpelec). Typical Value = 2.5.
Temperature detection lead time constant (Tsa). Typical Value = 0.
Temperature detection lag time constant (Tsb). Typical Value = 50.
Maximum valve position limit (Vmax). Typical Value = 1.
Minimum valve position limit (Vmin). Typical Value = 0.175.
No load fuel flow (Wfnl). Typical Value = 0.187.
Switch for fuel source characteristic to recognize that fuel flow, for a given fuel valve stroke, can be proportional to engine speed (Wfspd). true = fuel flow proportional to speed (for some gas turbines and diesel engines with positive displacement fuel injectors) false = fuel control system keeps fuel flow independent of engine speed. Typical Value = false.
Single shaft gas turbine.
Single shaft gas turbine.
Reference to the superclass object.
Ambient temperature load limit (Load Limit). Typical Value = 1.
Turbine damping factor (Dturb). Typical Value = 0.18.
Temperature limiter gain (Kt). Typical Value = 3.
Base for power values (MWbase) (> 0).
Permanent droop (R). Typical Value = 0.04.
Governor mechanism time constant (T1). T1 represents the natural valve positioning time constant of the governor for small disturbances, as seen when rate limiting is not in effect. Typical Value = 0.5.
Turbine power time constant (T2). T2 represents delay due to internal energy storage of the gas turbine engine. T2 can be used to give a rough approximation to the delay associated with acceleration of the compressor spool of a multi-shaft engine, or with the compressibility of gas in the plenum of a the free power turbine of an aero-derivative unit, for example. Typical Value = 0.5.
Turbine exhaust temperature time constant (T3). Typical Value = 3.
Maximum turbine power, PU of MWbase (Vmax). Typical Value = 1.
Minimum turbine power, PU of MWbase (Vmin). Typical Value = 0.
Modified single shaft gas turbine.
Modified single shaft gas turbine.
Reference to the superclass object.
Turbine power time constant numerator scale factor (a). Typical Value = 0.8.
Turbine power time constant denominator scale factor (b). Typical Value = 1.
Intentional dead-band width (db1). Unit = Hz. Typical Value = 0.
Unintentional dead-band (db2). Unit = MW. Typical Value = 0.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Fuel flow at zero power output (Fidle). Typical Value = 0.18.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2,PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Governor gain (Ka). Typical Value = 0.
Temperature limiter gain (Kt). Typical Value = 3.
Ambient temperature load limit (Lmax). Lmax is the turbine power output corresponding to the limiting exhaust gas temperature. Typical Value = 1.
Valve position change allowed at fast rate (Loadinc). Typical Value = 0.05.
Maximum long term fuel valve opening rate (Ltrate). Typical Value = 0.02.
Base for power values (MWbase) (> 0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Permanent droop (R). Typical Value = 0.04.
Maximum fuel valve opening rate (Rmax). Unit = PU/sec. Typical Value = 1.
Governor mechanism time constant (T1). T1 represents the natural valve positioning time constant of the governor for small disturbances, as seen when rate limiting is not in effect. Typical Value = 0.5.
Turbine power time constant (T2). T2 represents delay due to internal energy storage of the gas turbine engine. T2 can be used to give a rough approximation to the delay associated with acceleration of the compressor spool of a multi-shaft engine, or with the compressibility of gas in the plenum of the free power turbine of an aero-derivative unit, for example. Typical Value = 0.5.
Turbine exhaust temperature time constant (T3). T3 represents delay in the exhaust temperature and load limiting system. Typical Value = 3.
Governor lead time constant (T4). Typical Value = 0.
Governor lag time constant (T5). Typical Value = 0.
Valve position averaging time constant (Tltr). Typical Value = 10.
Maximum turbine power, PU of MWbase (Vmax). Typical Value = 1.
Minimum turbine power, PU of MWbase (Vmin). Typical Value = 0.
Gas turbine model.
Gas turbine model.
Reference to the superclass object.
Valve positioner (A).
Exhaust temperature Parameter (Af1). Unit = per unit temperature. Based on temperature in degrees C.
Coefficient equal to 0.5(1-speed) (Af2).
Valve positioner (B).
(Bf1). Bf1 = E(1-w) where E (speed sensitivity coefficient) is 0.55 to 0.65 x Tr. Unit = per unit temperature. Based on temperature in degrees C.
Turbine Torque Coefficient Khhv (depends on heating value of fuel stream in combustion chamber) (Bf2).
Valve positioner (C).
Coefficient defining fuel flow where power output is 0% (Cf2). Synchronous but no output. Typically 0.23 x Khhv (23% fuel flow).
Combustion reaction time delay (Ecr).
Turbine and exhaust delay (Etd).
Ratio of Fuel Adjustment (K3).
Gain of radiation shield (K4).
Gain of radiation shield (K5).
Minimum fuel flow (K6).
Fuel system feedback (Kf).
Base for power values (MWbase) (> 0). Unit = MW.
Fuel Control Time Constant (T).
Radiation shield time constant (T3).
Thermocouple time constant (T4).
Temperature control time constant (T5).
Temperature control (Tc). Unit = �F or �C depending on constants Af1 and Bf1.
Compressor discharge time constant (Tcd).
Fuel system time constant (Tf).
Maximum Turbine limit (Tmax).
Minimum Turbine limit (Tmin).
Rated temperature (Tr). Unit = �C depending on parameters Af1 and Bf1.
Turbine rating (Trate). Unit = MW.
Temperature controller integration rate (Tt).
Governor gain (1/droop) on turbine rating (W).
Governor lead time constant (X).
Governor lag time constant (Y) (>0).
Governor mode (Z). true = Droop false = ISO.
Generic turbogas with acceleration and temperature controller.
Generic turbogas with acceleration and temperature controller.
Reference to the superclass object.
Acceleration limit set-point (Bca). Unit = 1/s. Typical Value = 0.01.
Droop (bp). Typical Value = 0.05.
Exhaust temperature variation due to fuel flow increasing from 0 to 1 PU (deltaTc). Typical Value = 390.
Minimum fuel flow (Ka). Typical Value = 0.23.
Fuel system feedback (KAC). Typical Value = 0.
Acceleration control integral gain (Kca). Unit = 1/s. Typical Value = 100.
Gain of radiation shield (Ksi). Typical Value = 0.8.
Coefficient of transfer function of fuel valve positioner (Ky). Typical Value = 1.
Fuel flow maximum negative error value (MNEF). Typical Value = -0.05.
Fuel flow maximum positive error value (MXEF). Typical Value = 0.05.
Minimum fuel flow (RCMN). Typical Value = -0.1.
Maximum fuel flow (RCMX). Typical Value = 1.
Fuel control time constant (Tac). Typical Value = 0.1.
Compressor discharge volume time constant (Tc). Typical Value = 0.2.
Temperature controller derivative gain (Td). Typical Value = 3.3.
Turbine rated exhaust temperature correspondent to Pm=1 PU (Tfen). Typical Value = 540.
Time constant of speed governor (Tg). Typical Value = 0.05.
Time constant of radiation shield (Tsi). Typical Value = 15.
Temperature controller integration rate (Tt). Typical Value = 250.
Time constant of thermocouple (Ttc). Typical Value = 2.5.
Time constant of fuel valve positioner (Ty). Typical Value = 0.2.
Generic turbogas.
Generic turbogas.
Reference to the superclass object.
Droop (bp). Typical Value = 0.05.
Compressor gain (Ktm). Typical Value = 0.
Fuel flow maximum negative error value (MNEF). Typical Value = -0.05.
Fuel flow maximum positive error value (MXEF). Typical Value = 0.05.
Minimum valve opening (RYMN). Typical Value = 0.
Maximum valve opening (RYMX). Typical Value = 1.1.
Maximum gate opening velocity (TA). Typical Value = 3.
Maximum gate closing velocity (Tc). Typical Value = 0.5.
Fuel control time constant (Tcm). Typical Value = 0.1.
Compressor discharge volume time constant (Tm). Typical Value = 0.2.
Time constant of fuel valve positioner (Ty). Typical Value = 0.1.
Woodward Gas turbine governor model.
Woodward Gas turbine governor model.
Reference to the superclass object.
Valve positioner (A).
Exhaust temperature Parameter (Af1).
Coefficient equal to 0.5(1-speed) (Af2).
Valve positioner (B).
(Bf1). Bf1 = E(1-w) where E (speed sensitivity coefficient) is 0.55 to 0.65 x Tr.
Turbine Torque Coefficient Khhv (depends on heating value of fuel stream in combustion chamber) (Bf2).
Valve positioner (C).
Coefficient defining fuel flow where power output is 0% (Cf2). Synchronous but no output. Typically 0.23 x Khhv (23% fuel flow).
Combustion reaction time delay (Ecr).
Turbine and exhaust delay (Etd).
Ratio of Fuel Adjustment (K3).
Gain of radiation shield (K4).
Gain of radiation shield (K5).
Minimum fuel flow (K6).
Drop Governor Gain (Kd).
(Kdroop).
Fuel system feedback (Kf).
Isochronous Governor Gain (Ki).
PID Proportional gain (Kp).
Base for power values (MWbase) (> 0). Unit = MW.
Fuel Control Time Constant (T).
Radiation shield time constant (T3).
Thermocouple time constant (T4).
Temperature control time constant (T5).
Temperature control (Tc).
Compressor discharge time constant (Tcd).
Power transducer time constant (Td).
Fuel system time constant (Tf).
Maximum Turbine limit (Tmax).
Minimum Turbine limit (Tmin).
Rated temperature (Tr).
Turbine rating (Trate). Unit = MW.
Temperature controller integration rate (Tt).
Basic Hydro turbine governor model.
Basic Hydro turbine governor model.
Reference to the superclass object.
Turbine gain (At) (>0). Typical Value = 1.2.
Turbine damping factor (Dturb) (>=0). Typical Value = 0.5.
Maximum gate opening (Gmax) (>0). Typical Value = 1.
Minimum gate opening (Gmin) (>=0). Typical Value = 0.
Turbine nominal head (hdam). Typical Value = 1.
Base for power values (MWbase) (> 0). Unit = MW.
No-load flow at nominal head (qnl) (>=0). Typical Value = 0.08.
Permanent droop (R) (>0). Typical Value = 0.04.
Temporary droop (r) (>R). Typical Value = 0.3.
Filter time constant (Tf) (>0). Typical Value = 0.05.
Gate servo time constant (Tg) (>0). Typical Value = 0.5.
Washout time constant (Tr) (>0). Typical Value = 5.
Water inertia time constant (Tw) (>0). Typical Value = 1.
Maximum gate velocity (Vlem) (>0). Typical Value = 0.2.
IEEE hydro turbine governor model represents plants with straightforward penstock configurations and hydraulic-dashpot governors.
IEEE hydro turbine governor model represents plants with straightforward penstock configurations and hydraulic-dashpot governors.
Reference to the superclass object.
Turbine numerator multiplier (Aturb). Typical Value = -1.
Turbine denominator multiplier (Bturb). Typical Value = 0.5.
Intentional deadband width (db1). Unit = Hz. Typical Value = 0.
Unintentional deadband (db2). Unit = MW. Typical Value = 0.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Turbine gain (Kturb). Typical Value = 1.
Base for power values (MWbase) (> 0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Maximum gate opening (Pmax). Typical Value = 1.
Minimum gate opening; (Pmin). Typical Value = 0.
Permanent droop (Rperm). Typical Value = 0.05.
Temporary droop (Rtemp). Typical Value = 0.5.
Gate servo time constant (Tg). Typical Value = 0.5.
Pilot servo valve time constant (Tp). Typical Value = 0.03.
Dashpot time constant (Tr). Typical Value = 12.
Water inertia time constant (Tw). Typical Value = 2.
Maximum gate closing velocity (Uc) (<0). Unit = PU/sec. Typical Value = -0.1.
Maximum gate opening velocity (Uo). Unit = PU/sec. Typical Value = 0.1.
Modified IEEE Hydro Governor-Turbine Model.
Modified IEEE Hydro Governor-Turbine Model. This model differs from that defined in the IEEE modeling guideline paper in that the limits on gate position and velocity do not permit "wind up" of the upstream signals.
Reference to the superclass object.
Turbine gain (At). Typical Value = 1.2.
Intentional dead-band width (db1). Unit = Hz. Typical Value = 0.
Unintentional dead-band (db2). Unit = MW. Typical Value = 0.
Turbine damping factor (Dturb). Typical Value = 0.2.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Governor control flag (Cflag). true = PID control is active false = double derivative control is active. Typical Value = true.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Turbine nominal head (H0). Typical Value = 1.
Derivative gain (K1). Typical Value = 0.01.
Double derivative gain, if Cflag = -1 (K2). Typical Value = 2.5.
Gate servo gain (Kg). Typical Value = 2.
Integral gain (Ki). Typical Value = 0.5.
Base for power values (MWbase) (> 0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Maximum gate opening, PU of MWbase (Pmax). Typical Value = 1.
Minimum gate opening, PU of MWbase (Pmin). Typical Value = 0.
No-load turbine flow at nominal head (Qnl). Typical Value = 0.08.
Steady-state droop, PU, for electrical power feedback (Relec). Typical Value = 0.05.
Steady-state droop, PU, for governor output feedback (Rgate). Typical Value = 0.
Input filter time constant (Td). Typical Value = 0.05.
Washout time constant (Tf). Typical Value = 0.1.
Gate servo time constant (Tp). Typical Value = 0.05.
Power feedback time constant (Tt). Typical Value = 0.2.
Water inertia time constant (Tw). Typical Value = 1.
Maximum gate closing velocity (Velcl). Unit = PU/sec. Typical Value = -0.2.
Maximum gate opening velocity (Velop). Unit = PU/sec. Typical Value = 0.2.
Hydro turbine and governor.
Hydro turbine and governor. Represents plants with straight-forward penstock configurations and hydraulic governors of traditional 'dashpot' type. This model can be used to represent simple, Francis, Pelton or Kaplan turbines.
Reference to the superclass object.
Turbine gain (At). Typical Value = 1.2.
Kaplan blade servo point 0 (Bgv0). Typical Value = 0.
Kaplan blade servo point 1 (Bgv1). Typical Value = 0.
Kaplan blade servo point 2 (Bgv2). Typical Value = 0. Typical Value Francis = 0, Kaplan = 0.1.
Kaplan blade servo point 3 (Bgv3). Typical Value = 0. Typical Value Francis = 0, Kaplan = 0.667.
Kaplan blade servo point 4 (Bgv4). Typical Value = 0. Typical Value Francis = 0, Kaplan = 0.9.
Kaplan blade servo point 5 (Bgv5). Typical Value = 0. Typical Value Francis = 0, Kaplan = 1.
Maximum blade adjustment factor (Bmax). Typical Value = 0. Typical Value Francis = 0, Kaplan = 1.1276.
Intentional deadband width (db1). Unit = Hz. Typical Value = 0.
Unintentional dead-band (db2). Unit = MW. Typical Value = 0.
Turbine damping factor (Dturb). Unit = delta P (PU of MWbase) / delta speed (PU).
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Maximum gate opening, PU of MWbase (Gmax). Typical Value = 1.
Minimum gate opening, PU of MWbase (Gmin). Typical Value = 0.
Nonlinear gain point 0, PU gv (Gv0). Typical Value = 0. Typical Value Francis = 0.1, Kaplan = 0.1.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0. Typical Value Francis = 0.4, Kaplan = 0.4.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0. Typical Value Francis = 0.5, Kaplan = 0.5.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0. Typical Value Francis = 0.7, Kaplan = 0.7.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0. Typical Value Francis = 0.8, Kaplan = 0.8.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0. Typical Value Francis = 0.9, Kaplan = 0.9.
Head available at dam (hdam). Typical Value = 1.
Base for power values (MWbase) (>0). Unit = MW.
Nonlinear gain point 0, PU power (Pgv0). Typical Value = 0.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0. Typical Value Francis = 0.42, Kaplan = 0.35.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0. Typical Value Francis = 0.56, Kaplan = 0.468.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0. Typical Value Francis = 0.8, Kaplan = 0.796.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0. Typical Value Francis = 0.9, Kaplan = 0.917.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0. Typical Value Francis = 0.97, Kaplan = 0.99.
No-load flow at nominal head (Qnl). Typical Value = 0.08. Typical Value Francis = 0, Kaplan = 0.
Permanent droop (Rperm). Typical Value = 0.05.
Temporary droop (Rtemp). Typical Value = 0.3.
Blade servo time constant (Tblade). Typical Value = 100.
Gate servo time constant (Tg) (>0). Typical Value = 0.5.
Pilot servo time constant (Tp). Typical Value = 0.1.
Dashpot time constant (Tr) (>0). Typical Value = 5.
Water inertia time constant (Tw) (>0). Typical Value = 1.
Max gate closing velocity (Uc). Typical Value = 0.2.
Max gate opening velocity (Uo). Typical Value = 0.2.
Double derivative hydro governor and turbine.
Double derivative hydro governor and turbine.
Reference to the superclass object.
Turbine numerator multiplier (Aturb) (note 3). Typical Value = -1.
Turbine denominator multiplier (Bturb) (note 3). Typical Value = 0.5.
Intentional dead-band width (db1). Unit = Hz. Typical Value = 0.
Unintentional dead-band (db2). Unit = MW. Typical Value = 0.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Maximum gate opening (Gmax). Typical Value = 0.
Minimum gate opening (Gmin). Typical Value = 0.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Input signal switch (Flag). true = Pe input is used false = feedback is received from CV. Flag is normally dependent on Tt. If Tf is zero, Flag is set to false. If Tf is not zero, Flag is set to true.
Single derivative gain (K1). Typical Value = 3.6.
Double derivative gain (K2). Typical Value = 0.2.
Gate servo gain (Kg). Typical Value = 3.
Integral gain (Ki). Typical Value = 1.
Base for power values (MWbase) (>0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Maximum gate opening, PU of MWbase (Pmax). Typical Value = 1.
Minimum gate opening, PU of MWbase (Pmin). Typical Value = 0.
Steady state droop (R). Typical Value = 0.05.
Input filter time constant (Td). Typical Value = 0.
Washout time constant (Tf). Typical Value = 0.1.
Gate servo time constant (Tp). Typical Value = 0.35.
Power feedback time constant (Tt). Typical Value = 0.02.
Turbine time constant (Tturb) (note 3). Typical Value = 0.8.
Maximum gate closing velocity (Velcl). Unit = PU/sec. Typical Value = -0.14.
Maximum gate opening velocity (Velop). Unit = PU/sec. Typical Value = 0.09.
Detailed hydro unit - Francis model.
Detailed hydro unit - Francis model. This model can be used to represent three types of governors.
Reference to the superclass object.
Opening section Seff at the maximum efficiency (Am). Typical Value = 0.7.
Area of the surge tank (AV0). Unit = m2. Typical Value = 30.
Area of the compensation tank (AV1). Unit = m2. Typical Value = 700.
Droop (Bp). Typical Value = 0.05.
Intentional dead-band width (DB1). Unit = Hz. Typical Value = 0.
Maximum efficiency (EtaMax). Typical Value = 1.05.
Governor control flag (Cflag). Typical Value = mechanicHydrolicTachoAccelerator.
Head of compensation chamber water level with respect to the level of penstock (H1). Unit = m. Typical Value = 4.
Head of surge tank water level with respect to the level of penstock (H2). Unit = m. Typical Value = 40.
Rated hydraulic head (Hn). Unit = m. Typical Value = 250.
Penstock loss coefficient (due to friction) (Kc). Typical Value = 0.025.
Water tunnel and surge chamber loss coefficient (due to friction) (Kg). Typical Value = 0.025.
Washout gain (Kt). Typical Value = 0.25.
No-load turbine flow at nominal head (Qc0). Typical Value = 0.21.
Rated flow (Qn). Unit = m3/s. Typical Value = 40.
Derivative gain (Ta). Typical Value = 3.
Washout time constant (Td). Typical Value = 3.
Gate servo time constant (Ts). Typical Value = 0.5.
Water inertia time constant (Twnc). Typical Value = 1.
Water tunnel and surge chamber inertia time constant (Twng). Typical Value = 3.
Derivative feedback gain (Tx). Typical Value = 1.
Maximum gate opening velocity (Va). Unit = PU/sec. Typical Value = 0.011.
Maximum gate opening (ValvMax). Typical Value = 1.
Minimum gate opening (ValvMin). Typical Value = 0.
Maximum gate closing velocity (Vc). Unit = PU/sec. Typical Value = -0.011.
Water tunnel and surge chamber simulation (Tflag). true = enable of water tunnel and surge chamber simulation false = inhibit of water tunnel and surge chamber simulation. Typical Value = false.
Head of upper water level with respect to the level of penstock (Zsfc). Unit = m. Typical Value = 25.
IEEE Simplified Hydro Governor-Turbine Model.
IEEE Simplified Hydro Governor-Turbine Model. Used for Mechanical-Hydraulic and Electro-Hydraulic turbine governors, with our without steam feedback. Typical values given are for Mechanical-Hydraulic.
Reference to the superclass object.
Governor gain (K).
Base for power values (MWbase) (> 0). Unit = MW.
Gate maximum (Pmax).
Gate minimum (Pmin).
Governor lag time constant (T1). Typical Value = 0.25.
Governor lead time constant (T2). Typical Value = 0.
Gate actuator time constant (T3). Typical Value = 0.1.
Water starting time (T4).
IEEE hydro turbine governor model represents plants with straightforward penstock configurations and hydraulic-dashpot governors.
IEEE hydro turbine governor model represents plants with straightforward penstock configurations and hydraulic-dashpot governors. Ref<font color="#0f0f0f">erence: IEEE Transactions on Power Apparatus and Systems</font>
Reference to the superclass object.
Turbine numerator multiplier (Aturb). Typical Value = -1.
Turbine denominator multiplier (Bturb). Typical Value = 0.5.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Turbine gain (Kturb). Typical Value = 1.
Base for power values (MWbase) (> 0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Maximum gate opening (Pmax). Typical Value = 1.
Minimum gate opening (Pmin). Typical Value = 0.
Permanent droop (Rperm). Typical Value = 0.05.
Temporary droop (Rtemp). Typical Value = 0.5.
Gate servo time constant (Tg). Typical Value = 0.5.
Pilot servo valve time constant (Tp). Typical Value = 0.03.
Dashpot time constant (Tr). Typical Value = 12.
Water inertia time constant (Tw). Typical Value = 2.
Maximum gate closing velocity (Uc) (<0). Typical Value = -0.1.
Maximum gate opening velocity (Uo). Unit = PU/sec. Typical Value = 0.1.
PID governor and turbine.
PID governor and turbine.
Reference to the superclass object.
Turbine numerator multiplier (Aturb) (note 3). Typical Value -1.
Turbine denominator multiplier (Bturb) (note 3). Typical Value = 0.5.
Intentional dead-band width (db1). Unit = Hz. Typical Value = 0.
Unintentional dead-band (db2). Unit = MW. Typical Value = 0.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Input signal switch (Flag). true = Pe input is used false = feedback is received from CV. Flag is normally dependent on Tt. If Tf is zero, Flag is set to false. If Tf is not zero, Flag is set to true. Typical Value = true.
Derivative gain (Kd). Typical Value = 1.11.
Gate servo gain (Kg). Typical Value = 2.5.
Integral gain (Ki). Typical Value = 0.36.
Proportional gain (Kp). Typical Value = 0.1.
Base for power values (MWbase) (>0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Maximum gate opening, PU of MWbase (Pmax). Typical Value = 1.
Minimum gate opening, PU of MWbase (Pmin). Typical Value = 0.
Steady state droop (R). Typical Value = 0.05.
Input filter time constant (Td). Typical Value = 0.
Washout time constant (Tf). Typical Value = 0.1.
Gate servo time constant (Tp). Typical Value = 0.35.
Power feedback time constant (Tt). Typical Value = 0.02.
Turbine time constant (Tturb) (note 3). Typical Value = 0.8.
Maximum gate closing velocity (Velcl). Unit = PU/sec. Typical Value = -0.14.
Maximum gate opening velocity (Velop). Unit = PU/sec. Typical Value = 0.09.
Hydro turbine and governor.
Hydro turbine and governor. Represents plants with straight forward penstock configurations and "three term" electro-hydraulic governors (i.e. Woodard electronic).
Reference to the superclass object.
Factor multiplying Tw (Atw). Typical Value = 0.
Turbine damping factor (D). Unit = delta P / delta speed. Typical Value = 0.
Feedback signal type flag (Flag). true = use gate position feedback signal false = use Pe.
Gate opening at speed no load (G0). Typical Value = 0.
Intermediate gate opening (G1). Typical Value = 0.
Intermediate gate opening (G2). Typical Value = 0.
Maximum gate opening (Gmax). Typical Value = 0.
Minimum gate opening (Gmin). Typical Value = 0.
Derivative gain (Kd). Typical Value = 0.
Reset gain (Ki). Unit = PU/ sec. Typical Value = 0.
Proportional gain (Kp). Typical Value = 0.
Base for power values (MWbase) (>0). Unit = MW.
Power at gate opening G1 (P1). Typical Value = 0.
Power at gate opening G2 (P2). Typical Value = 0.
Power at full opened gate (P3). Typical Value = 0.
Permanent drop (Rperm). Typical Value = 0.
Controller time constant (Ta) (>0). Typical Value = 0.
Gate servo time constant (Tb) (>0). Typical Value = 0.
Speed detector time constant (Treg). Typical Value = 0.
Water inertia time constant (Tw) (>0). Typical Value = 0.
Maximum gate opening velocity (Velmax). Unit = PU/sec. Typical Value = 0.
Maximum gate closing velocity (Velmin). Unit = PU/sec. Typical Value = 0.
Detailed hydro unit - Pelton model.
Detailed hydro unit - Pelton model. This model can be used to represent the dynamic related to water tunnel and surge chamber.
Reference to the superclass object.
Area of the surge tank (AV0). Unit = m2. Typical Value = 30.
Area of the compensation tank (AV1). Unit = m2. Typical Value = 700.
Droop (bp). Typical Value = 0.05.
Intentional dead-band width (DB1). Unit = Hz. Typical Value = 0.
Intentional dead-band width of valve opening error (DB2). Unit = Hz. Typical Value = 0.01.
Head of compensation chamber water level with respect to the level of penstock (H1). Unit = m. Typical Value = 4.
Head of surge tank water level with respect to the level of penstock (H2). Unit = m. Typical Value = 40.
Rated hydraulic head (Hn). Unit = m. Typical Value = 250.
Penstock loss coefficient (due to friction) (Kc). Typical Value = 0.025.
Water tunnel and surge chamber loss coefficient (due to friction) (Kg). Typical Value = -0.025.
No-load turbine flow at nominal head (Qc0). Typical Value = 0.05.
Rated flow (Qn). Unit = m3/s. Typical Value = 40.
Simplified Pelton model simulation (Sflag). true = enable of simplified Pelton model simulation false = enable of complete Pelton model simulation (non linear gain). Typical Value = false.
Static compensating characteristic (Cflag). true = enable of static compensating characteristic false = inhibit of static compensating characteristic. Typical Value = false.
Derivative gain (accelerometer time constant) (Ta). Typical Value = 3.
Gate servo time constant (Ts). Typical Value = 0.15.
Servomotor integrator time constant (TV). Typical Value = 0.3.
Water inertia time constant (Twnc). Typical Value = 1.
Water tunnel and surge chamber inertia time constant (Twng). Typical Value = 3.
Electronic integrator time constant (Tx). Typical Value = 0.5.
Maximum gate opening velocity (Va). Unit = PU/sec. Typical Value = 0.016.
Maximum gate opening (ValvMax). Typical Value = 1.
Minimum gate opening (ValvMin). Typical Value = 0.
Maximum servomotor valve opening velocity (Vav). Typical Value = 0.017.
Maximum gate closing velocity (Vc). Unit = PU/sec. Typical Value = -0.016.
Maximum servomotor valve closing velocity (Vcv). Typical Value = -0.017.
Water tunnel and surge chamber simulation (Tflag). true = enable of water tunnel and surge chamber simulation false = inhibit of water tunnel and surge chamber simulation. Typical Value = false.
Head of upper water level with respect to the level of penstock (Zsfc). Unit = m. Typical Value = 25.
Fourth order lead-lag governor and hydro turbine.
Fourth order lead-lag governor and hydro turbine.
Reference to the superclass object.
Turbine gain (At). Typical Value = 1.2.
Intentional dead-band width (db1). Unit = Hz. Typical Value = 0.
Unintentional dead-band (db2). Unit = MW. Typical Value = 0.
Turbine damping factor (Dturb). Typical Value = 0.2.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Maximum governor output (Gmax). Typical Value = 1.05.
Minimum governor output (Gmin). Typical Value = -0.05.
Nonlinear gain point 1, PU gv (Gv1). Typical Value = 0.
Nonlinear gain point 2, PU gv (Gv2). Typical Value = 0.
Nonlinear gain point 3, PU gv (Gv3). Typical Value = 0.
Nonlinear gain point 4, PU gv (Gv4). Typical Value = 0.
Nonlinear gain point 5, PU gv (Gv5). Typical Value = 0.
Nonlinear gain point 6, PU gv (Gv6). Typical Value = 0.
Turbine nominal head (H0). Typical Value = 1.
Input signal switch (Flag). true = Pe input is used false = feedback is received from CV. Flag is normally dependent on Tt. If Tf is zero, Flag is set to false. If Tf is not zero, Flag is set to true. Typical Value = true.
Gate servo gain (Kg). Typical Value = 2.
Integral gain (Ki). Typical Value = 0.5.
Base for power values (MWbase) (>0). Unit = MW.
Nonlinear gain point 1, PU power (Pgv1). Typical Value = 0.
Nonlinear gain point 2, PU power (Pgv2). Typical Value = 0.
Nonlinear gain point 3, PU power (Pgv3). Typical Value = 0.
Nonlinear gain point 4, PU power (Pgv4). Typical Value = 0.
Nonlinear gain point 5, PU power (Pgv5). Typical Value = 0.
Nonlinear gain point 6, PU power (Pgv6). Typical Value = 0.
Maximum gate opening, PU of MWbase (Pmax). Typical Value = 1.
Minimum gate opening, PU of MWbase (Pmin). Typical Value = 0.
No-load turbine flow at nominal head (Qnl). Typical Value = 0.08.
Steady-state droop (R). Typical Value = 0.05.
Lead time constant 1 (T1). Typical Value = 1.5.
Lag time constant 1 (T2). Typical Value = 0.1.
Lead time constant 2 (T3). Typical Value = 1.5.
Lag time constant 2 (T4). Typical Value = 0.1.
Lead time constant 3 (T5). Typical Value = 0.
Lag time constant 3 (T6). Typical Value = 0.05.
Lead time constant 4 (T7). Typical Value = 0.
Lag time constant 4 (T8). Typical Value = 0.05.
Input filter time constant (Td). Typical Value = 0.05.
Gate servo time constant (Tp). Typical Value = 0.05.
Power feedback time constant (Tt). Typical Value = 0.
Water inertia time constant (Tw). Typical Value = 1.
Maximum gate closing velocity (Velcl). Unit = PU/sec. Typical Value = -0.2.
Maximum gate opening velocity (Velop). Unit = PU/sec. Typical Value = 0.2.
Woodward Electric Hydro Governor Model.
Woodward Electric Hydro Governor Model.
Reference to the superclass object.
Speed Dead Band (db).
Value to allow the integral controller to advance beyond the gate limits (Dicn).
Value to allow the Pilot valve controller to advance beyond the gate limits (Dpv).
Turbine damping factor (Dturb). Unit = delta P (PU of MWbase) / delta speed (PU).
Feedback signal selection (Sw). true = PID Output (if R-Perm-Gate=droop and R-Perm-Pe=0) false = Electrical Power (if R-Perm-Gate=0 and R-Perm-Pe=droop) or false = Gate Position (if R-Perm-Gate=droop and R-Perm-Pe=0).
Flow Gate 1 (Fl1). Flow value for gate position point 1 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Flow Gate 2 (Fl2). Flow value for gate position point 2 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Flow Gate 3 (Fl3). Flow value for gate position point 3 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Flow Gate 4 (Fl4). Flow value for gate position point 4 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Flow Gate 5 (Fl5). Flow value for gate position point 5 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Flow P1 (Fp1). Turbine Flow value for point 1 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P10 (Fp10). Turbine Flow value for point 10 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P2 (Fp2). Turbine Flow value for point 2 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P3 (Fp3). Turbine Flow value for point 3 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P4 (Fp4). Turbine Flow value for point 4 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P5 (Fp5). Turbine Flow value for point 5 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P6 (Fp6). Turbine Flow value for point 6 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P7 (Fp7). Turbine Flow value for point 7 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P8 (Fp8). Turbine Flow value for point 8 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Flow P9 (Fp9). Turbine Flow value for point 9 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Maximum Gate Position (Gmax).
Minimum Gate Position (Gmin).
Maximum gate closing rate (Gtmxcl).
Maximum gate opening rate (Gtmxop).
Gate 1 (Gv1). Gate Position value for point 1 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Gate 2 (Gv2). Gate Position value for point 2 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Gate 3 (Gv3). Gate Position value for point 3 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Gate 4 (Gv4). Gate Position value for point 4 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Gate 5 (Gv5). Gate Position value for point 5 for lookup table representing water flow through the turbine as a function of gate position to produce steady state flow.
Derivative controller derivative gain (Kd).
Derivative controller Integral gain (Ki).
Derivative control gain (Kp).
Base for power values (MWbase) (>0). Unit = MW.
Pmss Flow P1 (Pmss1). Mechanical Power output Pmss for Turbine Flow point 1 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P10 (Pmss10). Mechanical Power output Pmss for Turbine Flow point 10 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P2 (Pmss2). Mechanical Power output Pmss for Turbine Flow point 2 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P3 (Pmss3). Mechanical Power output Pmss for Turbine Flow point 3 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P4 (Pmss4). Mechanical Power output Pmss for Turbine Flow point 4 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P5 (Pmss5). Mechanical Power output Pmss for Turbine Flow point 5 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P6 (Pmss6). Mechanical Power output Pmss for Turbine Flow point 6 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P7 (Pmss7). Mechanical Power output Pmss for Turbine Flow point 7 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P8 (Pmss8). Mechanical Power output Pmss for Turbine Flow point 8 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Pmss Flow P9 (Pmss9). Mechanical Power output Pmss for Turbine Flow point 9 for lookup table representing per unit mechanical power on machine MVA rating as a function of turbine flow.
Permanent droop for governor output feedback (R-Perm-Gate).
Permanent droop for electrical power feedback (R-Perm-Pe).
Derivative controller time constant to limit the derivative characteristic beyond a breakdown frequency to avoid amplification of high-frequency noise (Td).
Distributive Valve time lag time constant (Tdv).
Value to allow the Distribution valve controller to advance beyond the gate movement rate limit (Tg).
Pilot Valve time lag time constant (Tp).
Electrical power droop time constant (Tpe).
Water inertia time constant (Tw) (>0).
Woodward PID Hydro Governor.
Woodward PID Hydro Governor.
Reference to the superclass object.
Turbine damping factor (D). Unit = delta P / delta speed.
Gate opening Limit Maximum (Gatmax).
Gate opening Limit Minimum (Gatmin).
Gate position 1 (Gv1).
Gate position 2 (Gv2).
Gate position 3 (Gv3).
Derivative gain (Kd). Typical Value = 1.11.
Reset gain (Ki). Typical Value = 0.36.
Proportional gain (Kp). Typical Value = 0.1.
Base for power values (MWbase) (>0). Unit = MW.
Output at Gv1 PU of MWbase (Pgv1).
Output at Gv2 PU of MWbase (Pgv2).
Output at Gv3 PU of MWbase (Pgv3).
Maximum Power Output (Pmax).
Minimum Power Output (Pmin).
Permanent drop (Reg).
Controller time constant (Ta) (>0). Typical Value = 0.
Gate servo time constant (Tb) (>0). Typical Value = 0.
Speed detector time constant (Treg).
Water inertia time constant (Tw) (>0). Typical Value = 0.
Maximum gate opening velocity (Velmax). Unit = PU/sec. Typical Value = 0.
Maximum gate closing velocity (Velmin). Unit = PU/sec. Typical Value = 0.
A simplified steam turbine governor model.
A simplified steam turbine governor model.
Reference to the superclass object.
Turbine damping coefficient (Dt). Unit = delta P / delta speed. Typical Value = 0.
Base for power values (MWbase) (>0). Unit = MW.
Permanent droop (R). Typical Value = 0.05.
Steam bowl time constant (T1). Typical Value = 0.5.
Numerator time constant of T2/T3 block (T2). Typical Value = 3.
Reheater time constant (T3). Typical Value = 10.
Maximum valve position, PU of mwcap (Vmax). Typical Value = 1.
Minimum valve position, PU of mwcap (Vmin). Typical Value = 0.
Steam turbine governor model, based on the GovSteamIEEE1 model (with optional deadband and nonlinear valve gain added).
Steam turbine governor model, based on the GovSteamIEEE1 model (with optional deadband and nonlinear valve gain added).
Reference to the superclass object.
Intentional deadband width (db1). Unit = Hz. Typical Value = 0.
Unintentional deadband (db2). Unit = MW. Typical Value = 0.
Intentional db hysteresis (eps). Unit = Hz. Typical Value = 0.
Nonlinear gain valve position point 1 (GV1). Typical Value = 0.
Nonlinear gain valve position point 2 (GV2). Typical Value = 0.4.
Nonlinear gain valve position point 3 (GV3). Typical Value = 0.5.
Nonlinear gain valve position point 4 (GV4). Typical Value = 0.6.
Nonlinear gain valve position point 5 (GV5). Typical Value = 1.
Nonlinear gain valve position point 6 (GV6). Typical Value = 0.
Governor gain (reciprocal of droop) (K) (>0). Typical Value = 25.
Fraction of HP shaft power after first boiler pass (K1). Typical Value = 0.2.
Fraction of LP shaft power after first boiler pass (K2). Typical Value = 0.
Fraction of HP shaft power after second boiler pass (K3). Typical Value = 0.3.
Fraction of LP shaft power after second boiler pass (K4). Typical Value = 0.
Fraction of HP shaft power after third boiler pass (K5). Typical Value = 0.5.
Fraction of LP shaft power after third boiler pass (K6). Typical Value = 0.
Fraction of HP shaft power after fourth boiler pass (K7). Typical Value = 0.
Fraction of LP shaft power after fourth boiler pass (K8). Typical Value = 0.
Base for power values (MWbase) (>0). Unit = MW.
Nonlinear gain power value point 1 (Pgv1). Typical Value = 0.
Nonlinear gain power value point 2 (Pgv2). Typical Value = 0.75.
Nonlinear gain power value point 3 (Pgv3). Typical Value = 0.91.
Nonlinear gain power value point 4 (Pgv4). Typical Value = 0.98.
Nonlinear gain power value point 5 (Pgv5). Typical Value = 1.
Nonlinear gain power value point 6 (Pgv6). Typical Value = 0.
Maximum valve opening (Pmax) (> Pmin). Typical Value = 1.
Minimum valve opening (Pmin) (>=0). Typical Value = 0.
Intentional deadband indicator. true = intentional deadband is applied false = intentional deadband is not applied. Typical Value = true.
Unintentional deadband location. true = intentional deadband is applied before point "A" false = intentional deadband is applied after point "A". Typical Value = true.
Governor lag time constant (T1). Typical Value = 0.
Governor lead time constant (T2). Typical Value = 0.
Valve positioner time constant (T3) (>0). Typical Value = 0.1.
Inlet piping/steam bowl time constant (T4). Typical Value = 0.3.
Time constant of second boiler pass (T5). Typical Value = 5.
Time constant of third boiler pass (T6). Typical Value = 0.5.
Time constant of fourth boiler pass (T7). Typical Value = 0.
Maximum valve closing velocity (Uc) (<0). Unit = PU/sec. Typical Value = -10.
Maximum valve opening velocity (Uo) (>0). Unit = PU/sec. Typical Value = 1.
Nonlinear valve characteristic. true = nonlinear valve characteristic is used false = nonlinear valve characteristic is not used. Typical Value = true.
Simplified governor model.
Simplified governor model.
Reference to the superclass object.
Frequency dead band (DBF). Typical Value = 0.
Governor gain (reciprocal of droop) (K). Typical Value = 20.
Fuel flow maximum negative error value (MNEF). Typical Value = -1.
Fuel flow maximum positive error value (MXEF). Typical Value = 1.
Maximum fuel flow (PMAX). Typical Value = 1.
Minimum fuel flow (PMIN). Typical Value = 0.
Governor lag time constant (T1) (>0). Typical Value = 0.45.
Governor lead time constant (T2) (may be 0). Typical Value = 0.
Cross compound turbine governor model.
Cross compound turbine governor model.
Reference to the superclass object.
HP damping factor (Dhp). Typical Value = 0.
LP damping factor (Dlp). Typical Value = 0.
Fraction of HP power ahead of reheater (Fhp). Typical Value = 0.3.
Fraction of LP power ahead of reheater (Flp). Typical Value = 0.7.
Base for power values (MWbase) (>0). Unit = MW.
Maximum HP value position (Pmaxhp). Typical Value = 1.
Maximum LP value position (Pmaxlp). Typical Value = 1.
HP governor droop (Rhp). Typical Value = 0.05.
LP governor droop (Rlp). Typical Value = 0.05.
HP governor time constant (T1hp). Typical Value = 0.1.
LP governor time constant (T1lp). Typical Value = 0.1.
HP turbine time constant (T3hp). Typical Value = 0.1.
LP turbine time constant (T3lp). Typical Value = 0.1.
HP turbine time constant (T4hp). Typical Value = 0.1.
LP turbine time constant (T4lp). Typical Value = 0.1.
HP reheater time constant (T5hp). Typical Value = 10.
LP reheater time constant (T5lp). Typical Value = 10.
Simplified model of boiler and steam turbine with PID governor.
Simplified model of boiler and steam turbine with PID governor.
Reference to the superclass object.
Control valves rate closing limit (Chc). Unit = PU/sec. Typical Value = -3.3.
Control valves rate opening limit (Cho). Unit = PU/sec. Typical Value = 0.17.
Intercept valves rate closing limit (Cic). Typical Value = -2.2.
Intercept valves rate opening limit (Cio). Typical Value = 0.123.
Dead band of the frequency corrector (db1). Typical Value = 0.
Dead band of the speed governor (db2). Typical Value = 0.0004.
Maximum control valve position (Hhpmax). Typical Value = 1.
Gain of the power controller (Ke). Typical Value = 0.65.
Gain of the frequency corrector (Kfcor). Typical Value = 20.
Fraction of total turbine output generated by HP part (Khp). Typical Value = 0.277.
Fraction of total turbine output generated by HP part (Klp). Typical Value = 0.723.
Gain of the speed governor (Kwcor). Typical Value = 20.
Base for power values (MWbase) (>0). Unit = MW.
Maximal active power of the turbine (Pmax). Typical Value = 1.
Maximum low pressure limit (Prhmax). Typical Value = 1.4.
Intercept valves transfer limit (Simx). Typical Value = 0.425.
Boiler time constant (Tb). Typical Value = 100.
Derivative time constant of the power controller (Tdp). Typical Value = 0.
Electro hydraulic transducer (Ten). Typical Value = 0.1.
Frequency transducer time constant (Tf). Typical Value = 0.
Time constant of the power controller (Tfp). Typical Value = 0.
High pressure (HP) time constant of the turbine (Thp). Typical Value = 0.31.
Integral time constant of the power controller (Tip). Typical Value = 2.
Low pressure(LP) time constant of the turbine (Tlp). Typical Value = 0.45.
Power transducer time constant (Tp). Typical Value = 0.07.
Reheater time constant of the turbine (Trh). Typical Value = 8.
Control valves servo time constant (Tvhp). Typical Value = 0.1.
Intercept valves servo time constant (Tvip). Typical Value = 0.15.
Speed transducer time constant (Tw). Typical Value = 0.02.
Upper limit for frequency correction (Wfmax). Typical Value = 0.05.
Lower limit for frequency correction (Wfmin). Typical Value = -0.05.
Emergency speed control lower limit (wmax1). Typical Value = 1.025.
Emergency speed control upper limit (wmax2). Typical Value = 1.05.
Upper limit for the speed governor (Wwmax). Typical Value = 0.1.
Lower limit for the speed governor frequency correction (Wwmin). Typical Value = -1.
Steam turbine governor with reheat time constants and modeling of the effects of fast valve closing to reduce mechanical power.
Steam turbine governor with reheat time constants and modeling of the effects of fast valve closing to reduce mechanical power.
Reference to the superclass object.
(Dt).
Fraction of the turbine power developed by turbine sections not involved in fast valving (K).
Alternate Base used instead of Machine base in equipment model if necessary (MWbase) (>0). Unit = MW.
(R).
Governor time constant (T1).
Reheater time constant (T3).
Time after initial time for valve to close (Ta).
Time after initial time for valve to begin opening (Tb).
Time after initial time for valve to become fully open (Tc).
Initial time to begin fast valving (Ti).
Time constant with which power falls off after intercept valve closure (Tt).
(Vmax).
(Vmin).
Simplified GovSteamIEEE1 Steam turbine governor model with Prmax limit and fast valving.
Simplified GovSteamIEEE1 Steam turbine governor model with Prmax limit and fast valving.
Reference to the superclass object.
Governor gain, (reciprocal of droop) (K). Typical Value = 20.
Fraction of turbine power developed after first boiler pass (K1). Typical Value = 0.2.
Fraction of turbine power developed after second boiler pass (K2). Typical Value = 0.2.
Fraction of hp turbine power developed after crossover or third boiler pass (K3). Typical Value = 0.6.
Base for power values (MWbase) (>0). Unit = MW.
Maximum valve opening, PU of MWbase (Pmax). Typical Value = 1.
Minimum valve opening, PU of MWbase (Pmin). Typical Value = 0.
Max. pressure in reheater (Prmax). Typical Value = 1.
Governor lead time constant (T1). Typical Value = 0.
Governor lag time constant (T2). Typical Value = 0.
Valve positioner time constant (T3). Typical Value = 0.
Inlet piping/steam bowl time constant (T4). Typical Value = 0.2.
Time constant of second boiler pass (i.e. reheater) (T5). Typical Value = 0.5.
Time constant of crossover or third boiler pass (T6). Typical Value = 10.
Time to close intercept valve (IV) (Ta). Typical Value = 0.97.
Time until IV starts to reopen (Tb). Typical Value = 0.98.
Time until IV is fully open (Tc). Typical Value = 0.99.
Maximum valve closing velocity (Uc). Unit = PU/sec. Typical Value = -1.
Maximum valve opening velocity (Uo). Unit = PU/sec. Typical Value = 0.1.
Detailed electro-hydraulic governor for steam unit.
Detailed electro-hydraulic governor for steam unit.
Reference to the superclass object.
Minimum value of pressure regulator output (Cpsmn). Typical Value = -1.
Maximum value of pressure regulator output (Cpsmx). Typical Value = 1.
Minimum value of regulator set-point (Crmn). Typical Value = 0.
Maximum value of regulator set-point (Crmx). Typical Value = 1.2.
Derivative gain of pressure regulator (Kdc). Typical Value = 1.
Frequency bias (reciprocal of droop) (Kf1). Typical Value = 20.
Frequency control (reciprocal of droop) (Kf3). Typical Value = 20.
Fraction of total turbine output generated by HP part (Khp). Typical Value = 0.35.
Integral gain of pressure regulator (Kic). Typical Value = 0.0033.
Integral gain of pressure feedback regulator (Kip). Typical Value = 0.5.
Integral gain of electro-hydraulic regulator (Kit). Typical Value = 0.04.
First gain coefficient of intercept valves characteristic (Kmp1). Typical Value = 0.5.
Second gain coefficient of intercept valves characteristic (Kmp2). Typical Value = 3.5.
Proportional gain of pressure regulator (Kpc). Typical Value = 0.5.
Proportional gain of pressure feedback regulator (Kpp). Typical Value = 1.
Proportional gain of electro-hydraulic regulator (Kpt). Typical Value = 0.3.
Maximum variation of fuel flow (Krc). Typical Value = 0.05.
Pressure loss due to flow friction in the boiler tubes (Ksh). Typical Value = 0.08.
Maximum negative power error (Lpi). Typical Value = -0.15.
Maximum positive power error (Lps). Typical Value = 0.03.
Lower limit for frequency correction (MNEF). Typical Value = -0.05.
Upper limit for frequency correction (MXEF). Typical Value = 0.05.
First value of pressure set point static characteristic (Pr1). Typical Value = 0.2.
Second value of pressure set point static characteristic, corresponding to Ps0 = 1.0 PU (Pr2). Typical Value = 0.75.
Minimum value of pressure set point static characteristic (Psmn). Typical Value = 1.
Minimum value of integral regulator (Rsmimn). Typical Value = 0.
Maximum value of integral regulator (Rsmimx). Typical Value = 1.1.
Minimum value of integral regulator (Rvgmn). Typical Value = 0.
Maximum value of integral regulator (Rvgmx). Typical Value = 1.2.
Minimum valve opening (Srmn). Typical Value = 0.
Maximum valve opening (Srmx). Typical Value = 1.1.
Intercept valves characteristic discontinuity point (Srsmp). Typical Value = 0.43.
Maximum regulator gate closing velocity (Svmn). Typical Value = -0.0333.
Maximum regulator gate opening velocity (Svmx). Typical Value = 0.0333.
Control valves rate opening time (Ta). Typical Value = 0.8.
Intercept valves rate opening time (Tam). Typical Value = 0.8.
Control valves rate closing time (Tc). Typical Value = 0.5.
Intercept valves rate closing time (Tcm). Typical Value = 0.5.
Derivative time constant of pressure regulator (Tdc). Typical Value = 90.
Time constant of fuel regulation (Tf1). Typical Value = 10.
Time constant of steam chest (Tf2). Typical Value = 10.
High pressure (HP) time constant of the turbine (Thp). Typical Value = 0.15.
Low pressure (LP) time constant of the turbine (Tmp). Typical Value = 0.4.
Reheater time constant of the turbine (Trh). Typical Value = 10.
Boiler time constant (Tv). Typical Value = 60.
Control valves servo time constant (Ty). Typical Value = 0.1.
Coefficient of linearized equations of turbine (Stodola formulation) (Y). Typical Value = 0.13.
Minimum control valve position (Yhpmn). Typical Value = 0.
Maximum control valve position (Yhpmx). Typical Value = 1.1.
Minimum intercept valve position (Ympmn). Typical Value = 0.
Maximum intercept valve position (Ympmx). Typical Value = 1.1.
IEEE steam turbine governor model.
IEEE steam turbine governor model. Ref<font color="#0f0f0f">erence: IEEE Transactions on Power Apparatus and Systems</font>
Reference to the superclass object.
Governor gain (reciprocal of droop) (K) (> 0). Typical Value = 25.
Fraction of HP shaft power after first boiler pass (K1). Typical Value = 0.2.
Fraction of LP shaft power after first boiler pass (K2). Typical Value = 0.
Fraction of HP shaft power after second boiler pass (K3). Typical Value = 0.3.
Fraction of LP shaft power after second boiler pass (K4). Typical Value = 0.
Fraction of HP shaft power after third boiler pass (K5). Typical Value = 0.5.
Fraction of LP shaft power after third boiler pass (K6). Typical Value = 0.
Fraction of HP shaft power after fourth boiler pass (K7). Typical Value = 0.
Fraction of LP shaft power after fourth boiler pass (K8). Typical Value = 0.
Base for power values (MWbase) (> 0).
Maximum valve opening (Pmax) (> Pmin). Typical Value = 1.
Minimum valve opening (Pmin) (>= 0). Typical Value = 0.
Governor lag time constant (T1). Typical Value = 0.
Governor lead time constant (T2). Typical Value = 0.
Valve positioner time constant (T3) (> 0). Typical Value = 0.1.
Inlet piping/steam bowl time constant (T4). Typical Value = 0.3.
Time constant of second boiler pass (T5). Typical Value = 5.
Time constant of third boiler pass (T6). Typical Value = 0.5.
Time constant of fourth boiler pass (T7). Typical Value = 0.
Maximum valve closing velocity (Uc) (< 0). Unit = PU/sec. Typical Value = -10.
Maximum valve opening velocity (Uo) (> 0). Unit = PU/sec. Typical Value = 1.
Simplified Steam turbine governor model.
Simplified Steam turbine governor model.
Reference to the superclass object.
One/per unit regulation (K1).
Fraction (K2).
Fraction (K3).
Base for power values (MWbase) (>0). Unit = MW.
Upper power limit (Pmax).
Lower power limit (Pmin).
Controller lag (T1).
Controller lead compensation (T2).
Governor lag (T3) (>0).
Delay due to steam inlet volumes associated with steam chest and inlet piping (T4).
Reheater delay including hot and cold leads (T5).
Delay due to IP-LP turbine, crossover pipes and LP end hoods (T6).
Relationship between the generating unit's gross active power output on the X-axis (measured at the terminals of the machine(s)) and the generating unit's net active power output on the Y-axis (based on utility-defined measurements at the power station).
Relationship between the generating unit's gross active power output on the X-axis (measured at the terminals of the machine(s)) and the generating unit's net active power output on the Y-axis (based on utility-defined measurements at the power station). Station service loads, when modeled, should be treated as non-conforming bus loads. There may be more than one curve, depending on the auxiliary equipment that is in service.
Reference to the superclass object.
A generating unit may have a gross active power to net active power curve, describing the losses and auxiliary power requirements of the unit.
A point where the system is grounded used for connecting conducting equipment to ground.
A point where the system is grounded used for connecting conducting equipment to ground. The power system model can have any number of grounds.
Reference to the superclass object.
Action taken with this ground.
Action on ground as a switching step.
Action on ground as a switching step.
Reference to the superclass object.
Switching action to perform.
The line segment that this ground action will affect. This is the only way to access relationship to clamp in case the ground needs to be placed along the line segment.
Ground on which this action is taken.
Equipment being grounded with this operation. In case of placing a ground anywhere along a line segment, you must use the clamp (to get the distance from one terminal), so use the explicit relation with line segment. In all other cases (including placing the ground at a line segment terminal), reference to one or more conducting equipment is sufficient.
Group to which this step belongs.
A manually operated or motor operated mechanical switching device used for isolating a circuit or equipment from ground.
A manually operated or motor operated mechanical switching device used for isolating a circuit or equipment from ground.
Reference to the superclass object.
A fixed impedance device used for grounding.
A fixed impedance device used for grounding.
Reference to the superclass object.
Reactance of device.
An object or a condition that is a danger for causing loss or perils to an asset and/or people.
An object or a condition that is a danger for causing loss or perils to an asset and/or people.
Reference to the superclass object.
Status of this hazard.
Type of this hazard.
Relationship between unit heat input in energy per time for main fuel (Y1-axis) and supplemental fuel (Y2-axis) versus unit output in active power (X-axis).
Relationship between unit heat input in energy per time for main fuel (Y1-axis) and supplemental fuel (Y2-axis) versus unit output in active power (X-axis). The quantity of main fuel used to sustain generation at this output level is prorated for throttling between definition points. The quantity of supplemental fuel used at this output level is fixed and not prorated.
Reference to the superclass object.
Power output - auxiliary power multiplier adjustment factor.
Power output - auxiliary power offset adjustment factor.
Heat input - efficiency multiplier adjustment factor.
Heat input - offset adjustment factor.
Flag is set to true when output is expressed in net active power.
A thermal generating unit may have a heat input curve.
Relationship between unit heat rate per active power (Y-axis) and unit output (X-axis).
Relationship between unit heat rate per active power (Y-axis) and unit output (X-axis). The heat input is from all fuels.
Reference to the superclass object.
Flag is set to true when output is expressed in net active power.
A thermal generating unit may have a heat rate curve.
The heat recovery system associated with combustion turbines in order to produce steam for combined cycle plants.
The heat recovery system associated with combustion turbines in order to produce steam for combined cycle plants.
Reference to the superclass object.
The steam supply rating in kilopounds per hour, if dual pressure boiler.
A HostControlArea has a set of tie points and a set of generator controls (i.e., AGC).
A HostControlArea has a set of tie points and a set of generator controls (i.e., AGC). It also has a total load, including transmission and distribution losses.
Reference to the superclass object.
The area's present control mode: (CF = constant frequency) or (CTL = constant tie-line) or (TLB = tie-line bias) or (OFF = off control)
end effective date
The present power system frequency set point for automatic generation control
The control area's frequency bias factor, in MW/0.1 Hz, for automatic generation control (AGC)
start effective date
undocumented
A ControlAreaCompany controls a ControlArea.
undocumented
An indicator specifying that a resource shall have an Hourly Pre-Dispatch.
An indicator specifying that a resource shall have an Hourly Pre-Dispatch. The resource could be a RegisteredGenerator or a RegisteredInterTie.
Reference to the superclass object.
Flag defining that for this hour in the resource bid the resource shall have an hourly pre-dispatch.
Relationship between unit efficiency in percent and unit output active power for a given net head in meters.
Relationship between unit efficiency in percent and unit output active power for a given net head in meters. The relationship between efficiency, discharge, head, and power output is expressed as follows: E =KP/HQ
Reference to the superclass object.
A hydro generating unit has an efficiency curve.
A generating unit whose prime mover is a hydraulic turbine (e.g., Francis, Pelton, Kaplan).
A generating unit whose prime mover is a hydraulic turbine (e.g., Francis, Pelton, Kaplan).
Reference to the superclass object.
Energy conversion capability for generating.
The equivalent cost of water that drives the hydro turbine.
The hydro generating unit belongs to a hydro power plant.
A hydro generating unit has a penstock loss curve.
A hydro power station which can generate or pump.
A hydro power station which can generate or pump. When generating, the generator turbines receive water from an upper reservoir. When pumping, the pumps receive their water from a lower reservoir.
Reference to the superclass object.
Water travel delay from tailbay to next downstream hydro power station.
The hydro plant's generating rating active power for rated head conditions.
The type of hydro power plant water storage.
Type and configuration of hydro plant penstock(s).
Total plant discharge capacity.
The plant's rated gross head.
The hydro plant's pumping rating active power for rated head conditions.
A code describing the type (or absence) of surge tank that is associated with the hydro power plant.
The level at which the surge tank spills.
Generators are supplied water from or pumps discharge water to an upstream reservoir.
Generators discharge water to or pumps are supplied water from a downstream reservoir.
A synchronous motor-driven pump, typically associated with a pumped storage plant.
A synchronous motor-driven pump, typically associated with a pumped storage plant.
Reference to the superclass object.
The pumping discharge under maximum head conditions, usually at full gate.
The pumping discharge under minimum head conditions, usually at full gate.
The pumping power under maximum head conditions, usually at full gate.
The pumping power under minimum head conditions, usually at full gate.
The hydro pump may be a member of a pumped storage plant or a pump for distributing water.
The hydro pump has a pumping schedule over time, indicating when pumping is to occur.
The synchronous machine drives the turbine which moves the water from a low elevation to a higher elevation. The direction of machine rotation for pumping may or may not be the same as for generating.
The hydro pump's Operator-approved current operating schedule (or plan), typically produced with the aid of unit commitment type analyses.
The hydro pump's Operator-approved current operating schedule (or plan), typically produced with the aid of unit commitment type analyses. The unit's operating schedule status is typically given as: (0=unavailable) (1=avilable to startup or shutdown) (2=must pump).
Reference to the superclass object.
The hydro pump has a pumping schedule over time, indicating when pumping is to occur.
A water driven prime mover.
A water driven prime mover. Typical turbine types are: Francis, Kaplan, and Pelton.
Reference to the superclass object.
Gate rate limit.
Gate upper limit.
Maximum efficiency active power at maximum head conditions.
Maximum efficiency active power at minimum head conditions.
Rated speed in number of revolutions.
Speed regulation.
Transient droop time constant.
Transient regulation.
Rated turbine active power.
Type of turbine.
Water starting time.
This class represents the TASE.2 Information Message Object.
This class represents the TASE.2 Information Message Object. The IdentifiedObject.name attribute must be non-null. The value of the attribute shall be used as the TASE.2 Information Reference, as specified by 60870-6-503.
Reference to the superclass object.
undocumented
The Local Reference attribute specifies a value agreed upon between sender and receiver of the Information Message. It further identifies the Information Message.
undocumented
The IdentifiedObject.name attribute must have a value.
The IdentifiedObject.name attribute must have a value. The name attribute shall be used as the DataValue name used for the exchange.
Reference to the superclass object.
undocumented
undocumented
IEC 61968 version number assigned to this UML model.
IEC 61968 version number assigned to this UML model.
Reference to the superclass object.
Form is YYYY-MM-DD for example for January 5, 2009 it is 2009-01-05.
Form is IEC61968CIMXXvYY where XX is the major CIM package version and the YY is the minor version. For example IEC61968CIM10v17.
This is the IEC 61970 CIM version number assigned to this UML model.
This is the IEC 61970 CIM version number assigned to this UML model.
Reference to the superclass object.
Form is YYYY-MM-DD for example for January 5, 2009 it is 2009-01-05.
Form is IEC61970CIMXXvYY where XX is the major CIM package version and the YY is the minor version. For example IEC61970CIM13v18.
IEC 62325 version number assigned to this UML model.
IEC 62325 version number assigned to this UML model.
Reference to the superclass object.
Form is YYYY-MM-DD for example for January 5, 2009 it is 2009-01-05.
Form is IEC62325CIMXXvYY where XX is the major CIM package version and the YY is the minor version. For example IEC62325CIM10v03.
This is a root class to provide common identification for all classes needing identification and naming attributes.
This is a root class to provide common identification for all classes needing identification and naming attributes.
Reference to the superclass object.
The aliasName is free text human readable name of the object alternative to IdentifiedObject.name. It may be non unique and may not correlate to a naming hierarchy.
The description is a free human readable text describing or naming the object. It may be non unique and may not correlate to a naming hierarchy.
Master resource identifier issued by a model authority. The mRID is globally unique within an exchange context. Global uniqueness is easily achieved by using a UUID, as specified in RFC 4122, for the mRID. The use of UUID is strongly recommended.
The name is any free human readable and possibly non unique text naming the object.
An account for tracking inadvertent interchange versus time for each control area.
An account for tracking inadvertent interchange versus time for each control area. A control area may have more than one inadvertent account in order to track inadvertent over one or more specific tie points in addition to the usual overall net inadvertent. Separate accounts would also be used to track designated time periods, such as on-peak and off-peak.
Reference to the superclass object.
A control area can have one or more net inadvertent interchange accounts
Description of a problem in the field that may be reported in a trouble ticket or come from another source.
Description of a problem in the field that may be reported in a trouble ticket or come from another source. It may have to do with an outage.
Reference to the superclass object.
Cause of this incident.
Outage for this incident.
Operator who owns this incident.
All works addressing this incident.
Hazardous situation associated with an incident.
Hazardous situation associated with an incident. Examples are line down, gas leak, fire, etc.
Reference to the superclass object.
Incident associated with this hazard.
Trouble ticket associated with this hazard.
Relationship between unit incremental heat rate in (delta energy/time) per (delta active power) and unit output in active power.
Relationship between unit incremental heat rate in (delta energy/time) per (delta active power) and unit output in active power. The IHR curve represents the slope of the HeatInputCurve. Note that the "incremental heat rate" and the "heat rate" have the same engineering units.
Reference to the superclass object.
Flag is set to true when output is expressed in net active power.
A thermal generating unit may have an incremental heat rate curve.
Individual pricing node based on Pnode
Individual pricing node based on Pnode
Reference to the superclass object.
undocumented
undocumented
undocumented
Natural water inflow to a reservoir, usually forecasted from predicted rain and snowmelt.
Natural water inflow to a reservoir, usually forecasted from predicted rain and snowmelt. Typically in one hour increments for up to 10 days. The forecast is given in average cubic meters per second over the time increment.
Reference to the superclass object.
A reservoir may have a "natural" inflow forecast.
Questions and answers associated with a type of document for purposes of clarification.
Questions and answers associated with a type of document for purposes of clarification. Questions may be predefined or ad hoc.
Reference to the superclass object.
Answer to question.
The date and time the quesiton was answered.
Remarks to qualify the answer.
The question code. If blank, refer to questionText.
Remarks to qualify the question in this situation.
For non-coded questions, the question is provided here.
The type of the question.
Documents the result of one inspection, for a given attribute of an asset.
Documents the result of one inspection, for a given attribute of an asset.
Reference to the superclass object.
Description of the conditions of the location where the asset resides.
Model of market clearing, relating to commitment instructions.
Model of market clearing, relating to commitment instructions. Identifies interval
Reference to the superclass object.
Model of market clearing, related to Dispatch Operating Point.
Model of market clearing, related to Dispatch Operating Point. Identifies interval
Reference to the superclass object.
Model of market clearing, related to Dispatch Operating Target (model of anticipatory dispatch).
Model of market clearing, related to Dispatch Operating Target (model of anticipatory dispatch). Identifies interval
Reference to the superclass object.
Indication that the system is currently operating in a contingency mode.
undocumented
Provides the necessary information (on a resource basis) to capture the Startup/Shutdown instruction results.
Provides the necessary information (on a resource basis) to capture the Startup/Shutdown instruction results. This information is relevant to the DA Market (RUC only) as well as the RT Market (HASP, Pre-dispatch, and Interval).
Reference to the superclass object.
undocumented
undocumented
Total cost associated with changing the status of the resource.
instruction source for market quality results (INS, ACT)
Time the resource should be at Pmin (for start ups). Time the resource is off line.
Indicator of either a Start-Up or a Shut-Down.
Manually Blocked Indicator (Yes/No). The instruction has been blocked by an Operator.
Minimum start up time required to bring the unit online (minutes). SCUC commitment period start-up time. Calculated start up time based on the StartUpTimeCurve provided with the Bid.
undocumented
undocumented
undocumented
undocumented
A type of agreement that provides the default method by which interchange schedules are to be integrated to obtain hourly MWh schedules for accounting.
A type of agreement that provides the default method by which interchange schedules are to be integrated to obtain hourly MWh schedules for accounting.
Reference to the superclass object.
The default method by which interchange schedules are to be integrated to obtain hourly MWh schedules for accounting. Method #1 is to integrate the instantaneous schedule between the hourly boundaries. Method #2 compensates for any up/down ramping that occurs across the hourly boundary (this is called block accounting).
undocumented
Quantity with integer value and associated unit information.
Quantity with integer value and associated unit information.
Reference to the superclass object.
undocumented
undocumented
undocumented
This class represents the inter tie bid
This class represents the inter tie bid
Reference to the superclass object.
The minimum hourly block for an Inter-Tie Resource supplied within the bid.
undocumented
Model of market clearing related to results at the inter-ties.
Model of market clearing related to results at the inter-ties. Identifies interval
Reference to the superclass object.
Response from an intertie resource acknowleging receipt of dispatch instructions
Response from an intertie resource acknowleging receipt of dispatch instructions
Reference to the superclass object.
The accepted mw amount by the responder. aka response mw.
The accept status submitted by the responder. Valid values are NON-RESPONSE, ACCEPT, DECLINE, PARTIAL.
MW amount associated with instruction. For 5 minute binding dispatches, this is the Goto MW or DOT
Part of the Composite key that downstream app uses to match the instruction
Part of the Composite key that downstream app uses to match the instruction
undocumented
Provides the tie point specific output from the market applications.
Provides the tie point specific output from the market applications. Currently, this is defined as the loop flow compensation MW value.
Reference to the superclass object.
Net Actual MW Flow
Net Dispatched MW
undocumented
undocumented
Existing Transmission Contract data for an interchange schedule
Existing Transmission Contract data for an interchange schedule
Reference to the superclass object.
Existing transmission contract number
Existing transmission contract usage MW value
undocumented
Interchange schedule class to hold information for interchange schedules such as import export type, energy type, and etc.
Interchange schedule class to hold information for interchange schedules such as import export type, energy type, and etc.
Reference to the superclass object.
To indicate a check out type such as adjusted capacity or dispatch capacity.
Import or export.
Energy product type.
Interval length.
Market type.
Operating date, hour.
To indicate an out-of-market (OOM) schedule.
Schedule type.
Wheeling Counter-Resource ID (required when Schedule Type=Wheel).
undocumented
undocumented
Indicates whether unit is eligible for treatment as a intermittent variable renewable resource
Indicates whether unit is eligible for treatment as a intermittent variable renewable resource
Reference to the superclass object.
Indicates whether a resource is eligible for PIRP program for a given hour
undocumented
There is one internal control area in the system, which is the single control area in the primary network company.
There is one internal control area in the system, which is the single control area in the primary network company. Real time generation control affects only the internal control area.
Reference to the superclass object.
undocumented
Time sequence of readings of the same reading type.
Time sequence of readings of the same reading type. Contained interval readings may need conversion through the application of an offset and a scalar defined in associated pending.
Reference to the superclass object.
Interval reading contained in this block.
Meter reading containing this interval block.
Pending calculation to apply to interval reading values contained by this block (after which the resulting reading type is different than the original because it reflects the conversion result).
Type information for interval reading values contained in this block.
Data captured at regular intervals of time.
Data captured at regular intervals of time. Interval data could be captured as incremental data, absolute data, or relative data. The source for the data is usually a tariff quantity or an engineering quantity. Data is typically captured in time-tagged, uniform, fixed-length intervals of 5 min, 10 min, 15 min, 30 min, or 60 min.
Reference to the superclass object.
The schedule has time points where the time between them varies.
The schedule has time points where the time between them varies.
Reference to the superclass object.
TimePoints for a schedule where the time between the points varies.
TimePoints for a schedule where the time between the points varies.
Reference to the superclass object.
The time is relative to the schedule starting time.
The first value at the time. The meaning of the value is defined by the derived type of the associated schedule.
The second value at the time. The meaning of the value is defined by the derived type of the associated schedule.
An IrregularTimePoint belongs to an IrregularIntervalSchedule.
Joint connects two or more cables.
Joint connects two or more cables. It includes the portion of cable under wipes, welds, or other seals.
Reference to the superclass object.
Configuration of joint.
Material used to fill the joint.
The type of insulation around the joint, classified according to the utility's asset management standards and practices.
A short section of conductor with negligible impedance which can be manually removed and replaced if the circuit is de-energized.
A short section of conductor with negligible impedance which can be manually removed and replaced if the circuit is de-energized. Note that zero-impedance branches can potentially be modeled by other equipment types.
Reference to the superclass object.
Action taken with this jumper.
Action on jumper as a switching step.
Action on jumper as a switching step.
Reference to the superclass object.
Switching action to perform.
Jumper on which this action is taken.
Group to which this step belongs.
A point where one or more conducting equipments are connected with zero resistance.
A point where one or more conducting equipments are connected with zero resistance.
Reference to the superclass object.
Labor used for work order.
Labor used for work order.
Reference to the superclass object.
Activity code identifies a specific and distinguishable unit of work.
Total cost for labor. Note that this may not be able to be derived from labor rate and time charged.
Time required to perform work.
The labor rate applied for work.
undocumented
undocumented
undocumented
Information about a particular piece of (land) property such as its use.
Information about a particular piece of (land) property such as its use. Ownership of the property may be determined through associations to Organisations and/or ErpPersons.
Reference to the superclass object.
Demographics around the site.
Reference allocated by the governing organisation (such as municipality) to this piece of land that has a formal reference to Surveyor General's records. The governing organisation is specified in associated Organisation.
Kind of (land) property, categorised according to its main functional use from the utility's perspective.
undocumented
undocumented
The spatail description of a piece of property.
Relationship between reservoir volume and reservoir level.
Relationship between reservoir volume and reservoir level. The volume is at the y-axis and the reservoir level at the x-axis.
Reference to the superclass object.
A reservoir may have a level versus volume relationship.
Dates for lifecycle events of an asset.
Dates for lifecycle events of an asset.
Reference to the superclass object.
(if applicable) Date current installation was completed, which may not be the same as the in-service date. Asset may have been installed at other locations previously. Ignored if asset is (1) not currently installed (e.g., stored in a depot) or (2) not intended to be installed (e.g., vehicle, tool).
Date the asset was manufactured.
Date the asset was purchased. Note that even though an asset may have been purchased, it may not have been received into inventory at the time of purchase.
Date the asset was received and first placed into inventory.
(if applicable) Date when the asset was last removed from service. Ignored if (1) not intended to be in service, or (2) currently in service.
(if applicable) Date the asset is permanently retired from service and may be scheduled for disposal. Ignored if asset is (1) currently in service, or (2) permanently removed from service.
Specifies one limit value for a Measurement.
Specifies one limit value for a Measurement. A Measurement typically has several limits that are kept together by the LimitSet class. The actual meaning and use of a Limit instance (i.e., if it is an alarm or warning limit or if it is a high or low limit) is not captured in the Limit class. However the name of a Limit instance may indicate both meaning and use.
Reference to the superclass object.
A limit calculation model used to compute an operational limit based on external input such as temperature.
A limit calculation model used to compute an operational limit based on external input such as temperature. These are intended to be shared among operational limits with the same calculation form that apply to a piece of equipment..
Reference to the superclass object.
The equipment for which this limit dependency model is organized under.
Specifies an operational limit is calculated by scaling another operational limit.
Specifies an operational limit is calculated by scaling another operational limit.
Reference to the superclass object.
The associated source limit is scaled by this value to compute the limit of the dependency model.
undocumented
Specifies a set of Limits that are associated with a Measurement.
Specifies a set of Limits that are associated with a Measurement. A Measurement may have several LimitSets corresponding to seasonal or other changing conditions. The condition is captured in the name and description attributes. The same LimitSet may be used for several Measurements. In particular percentage limits are used this way.
Reference to the superclass object.
Tells if the limit values are in percentage of normalValue or the specified Unit for Measurements and Controls.
Contains equipment beyond a substation belonging to a power transmission line.
Contains equipment beyond a substation belonging to a power transmission line.
Reference to the superclass object.
The sub-geographical region of the line.
Details on an amount line, with rounding, date and note.
Details on an amount line, with rounding, date and note.
Reference to the superclass object.
Amount for this line item.
Date and time when this line was created in the application process.
Free format note relevant to this line.
Totalised monetary value of all errors due to process rounding or truncating that is not reflected in 'amount'.
A fault that occurs on an AC line segment at some point along the length.
A fault that occurs on an AC line segment at some point along the length.
Reference to the superclass object.
The length to the place where the fault is located starting from terminal with sequence number 1 of the faulted line segment.
The line segment of this line fault.
A linear shunt compensator has banks or sections with equal admittance values.
A linear shunt compensator has banks or sections with equal admittance values.
Reference to the superclass object.
Zero sequence shunt (charging) susceptance per section
Positive sequence shunt (charging) susceptance per section
Zero sequence shunt (charging) conductance per section
Positive sequence shunt (charging) conductance per section
A per phase linear shunt compensator has banks or sections with equal admittance values.
A per phase linear shunt compensator has banks or sections with equal admittance values.
Reference to the superclass object.
Susceptance per section of the phase if shunt compensator is wye connected. Susceptance per section phase to phase if shunt compensator is delta connected.
Conductance per section for this phase if shunt compensator is wye connected. Conductance per section phase to phase if shunt compensator is delta connected.
Standard aggregate load model comprised of static and/or dynamic components.
Standard aggregate load model comprised of static and/or dynamic components. A static load model represents the sensitivity of the real and reactive power consumed by the load to the amplitude and frequency of the bus voltage. A dynamic load model can used to represent the aggregate response of the motor components of the load.
Reference to the superclass object.
Aggregate motor (dynamic) load associated with this aggregate load.
Aggregate static load associated with this aggregate load.
A specialized class of type AggregatedNode type.
A specialized class of type AggregatedNode type. Defines Load Aggregation Points.
Reference to the superclass object.
The class is the root or first level in a hierarchical structure for grouping of loads for the purpose of load flow load scaling.
The class is the root or first level in a hierarchical structure for grouping of loads for the purpose of load flow load scaling.
Reference to the superclass object.
Offer to supply energy/ancillary services from a load resource (participating load reduces consumption)
Offer to supply energy/ancillary services from a load resource (participating load reduces consumption)
Reference to the superclass object.
Maximum rate that load can be reduced (MW/minute)
load reduction initiation cost
load reduction initiation time
The date represents the NextMarketDate for which the load response bids apply to.
Flag indicated that the load reduction is metered. (See above) If priceSetting and meteredValue both equal 1, then the facility is eligible to set LMP in the real time market.
Minimum MW load below which it may not be reduced.
Minimum MW for a load reduction (e.g. MW rating of a discrete pump.
Cost in $ at the minimum reduced load
Shortest period load reduction shall be maintained before load can be restored to normal levels.
Shortest time that load shall be left at normal levels before a new load reduction.
Maximum rate load may be restored (MW/minute)
Flag to indicate that the facility can set LMP Works in tandem with Metered Value. Greater chance of this being dynamic than the Metered Value, however, it is requested that Price Setting and Metered Value stay at the same source. Currently no customers have implemented the metering capability, but if this option is implemented, then Price Setting could become dynamic. However, Metered Value will remain static.
Time period that is required from an order to reduce a load to the time that it takes to get to the minimum load reduction.
The fixed cost associated with committing a load reduction.
undocumented
undocumented
A mechanical switching device capable of making, carrying, and breaking currents under normal operating conditions.
A mechanical switching device capable of making, carrying, and breaking currents under normal operating conditions.
Reference to the superclass object.
This model combines static load and induction motor load effects.
This model combines static load and induction motor load effects. The dynamics of the motor are simplified by linearizing the induction machine equations.
Reference to the superclass object.
Active load-frequency dependence index (dynamic) (Epfd). Typical Value = 1.5.
Active load-frequency dependence index (static) (Epfs). Typical Value = 1.5.
Active load-voltage dependence index (dynamic) (Epvd). Typical Value = 0.7.
Active load-voltage dependence index (static) (Epvs). Typical Value = 0.7.
Reactive load-frequency dependence index (dynamic) (Eqfd). Typical Value = 0.
Reactive load-frequency dependence index (static) (Eqfs). Typical Value = 0.
Reactive load-voltage dependence index (dynamic) (Eqvd). Typical Value = 2.
Reactive load-voltage dependence index (static) (Eqvs). Typical Value = 2.
Inertia constant (H). Typical Value = 2.5.
Loading factor � ratio of initial P to motor MVA base (Lfrac). Typical Value = 0.8.
Fraction of constant-power load to be represented by this motor model (Pfrac) (>=0.0 and <=1.0). Typical Value = 0.5.
This class models the load distribution factors.
This class models the load distribution factors. This class should be used in one of two ways:
Reference to the superclass object.
Real power (MW) load distribution factor
Reactive power (MVAr) load distribution factor
undocumented
undocumented
Load whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Load whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
A standard feature of dynamic load behaviour modelling is the ability to associate the same behaviour to multiple energy consumers by means of a single aggregate load definition. Aggregate loads are used to represent all or part of the real and reactive load from one or more loads in the static (power flow) data. This load is usually the aggregation of many individual load devices and the load model is approximate representation of the aggregate response of the load devices to system disturbances. The load model is always applied to individual bus loads (energy consumers) but a single set of load model parameters can used for all loads in the grouping.
Reference to the superclass object.
Metered SubSystem Load Following Instruction
Metered SubSystem Load Following Instruction
Reference to the superclass object.
Instruction End Time
Load Following MW Positive for follow-up and negative for follow-down
Unique instruction id per instruction, assigned by the SC and provided to ADS. ADS passes through.
Instruction Start Time
undocumented
Model of load following capabilities that are entered by operators on a temporary basis.
Model of load following capabilities that are entered by operators on a temporary basis. Related to Registered Resources in Metered Subsystems
Reference to the superclass object.
Time the data entry was performed
temporarily manually entered LFD capacity
temporarily manually entered LFU capacity.
undocumented
undocumented
undocumented
undocumented
These load models (known also as generic non-linear dynamic (GNLD) load models) can be used in mid-term and long-term voltage stability simulations (i.e., to study voltage collapse), as they can replace a more detailed representation of aggregate load, including induction motors, thermostatically controlled and static loads.
These load models (known also as generic non-linear dynamic (GNLD) load models) can be used in mid-term and long-term voltage stability simulations (i.e., to study voltage collapse), as they can replace a more detailed representation of aggregate load, including induction motors, thermostatically controlled and static loads.
Reference to the superclass object.
Steady state voltage index for reactive power (BS).
Transient voltage index for reactive power (BT).
Type of generic non-linear load model.
Steady state voltage index for active power (LS).
Transient voltage index for active power (LT).
Dynamic portion of active load (PT).
Dynamic portion of reactive load (QT).
Time constant of lag function of active power (TP).
Time constant of lag function of reactive power (TQ).
The class is the third level in a hierarchical structure for grouping of loads for the purpose of load flow load scaling.
The class is the third level in a hierarchical structure for grouping of loads for the purpose of load flow load scaling.
Reference to the superclass object.
The SubLoadArea where the Loadgroup belongs.
Aggregate induction motor load.
Aggregate induction motor load. This model is used to represent a fraction of an ordinary load as "induction motor load". It allows load that is treated as ordinary constant power in power flow analysis to be represented by an induction motor in dynamic simulation. If Lpp = 0. or Lpp = Lp, or Tppo = 0., only one cage is represented. Magnetic saturation is not modelled. Either a "one-cage" or "two-cage" model of the induction machine can be modelled. Magnetic saturation is not modelled.
Reference to the superclass object.
Damping factor (D). Unit = delta P/delta speed. Typical Value = 2.
Inertia constant (H) (not=0). Typical Value = 0.4.
Loading factor � ratio of initial P to motor MVA base (Lfac). Typical Value = 0.8.
Transient reactance (Lp). Typical Value = 0.15.
Subtransient reactance (Lpp). Typical Value = 0.15.
Synchronous reactance (Ls). Typical Value = 3.2.
Fraction of constant-power load to be represented by this motor model (Pfrac) (>=0.0 and <=1.0). Typical Value = 0.3.
Stator resistance (Ra). Typical Value = 0.
Circuit breaker operating time (Tbkr). Typical Value = 0.08.
Transient rotor time constant (Tpo) (not=0). Typical Value = 1.
Subtransient rotor time constant (Tppo). Typical Value = 0.02.
Voltage trip pickup time (Tv). Typical Value = 0.1.
Voltage threshold for tripping (Vt). Typical Value = 0.7.
Aggregate load to which this aggregate motor (dynamic) load belongs.
Representing the ratio of the load share for the associated SC.
Representing the ratio of the load share for the associated SC.
Reference to the superclass object.
Interval End Time
Interval Start Time
Share in percentage of total Market load for the selected time interval.
undocumented
This is the price sensitivity that bidder expresses for allowing market load interruption.
This is the price sensitivity that bidder expresses for allowing market load interruption. Relationship between price (Y1-axis) vs. MW (X-axis).
Reference to the superclass object.
undocumented
This is the cureve that describes the load reduction time.
This is the cureve that describes the load reduction time. Relationship between time (Y1-axis) vs. MW (X-axis).
Reference to the superclass object.
type of the curve: Possible values are but not limited to: Max, Min,
Models the characteristic response of the load demand due to changes in system conditions such as voltage and frequency.
Models the characteristic response of the load demand due to changes in system conditions such as voltage and frequency. This is not related to demand response.
Reference to the superclass object.
Indicates the exponential voltage dependency model is to be used. If false, the coefficient model is to be used.
Portion of active power load modeled as constant current.
Portion of active power load modeled as constant impedance.
Portion of active power load modeled as constant power.
Exponent of per unit frequency effecting active power.
Exponent of per unit voltage effecting real power.
Portion of reactive power load modeled as constant current.
Portion of reactive power load modeled as constant impedance.
Portion of reactive power load modeled as constant power.
Exponent of per unit frequency effecting reactive power.
Exponent of per unit voltage effecting reactive power.
General static load model representing the sensitivity of the real and reactive power consumed by the load to the amplitude and frequency of the bus voltage.
General static load model representing the sensitivity of the real and reactive power consumed by the load to the amplitude and frequency of the bus voltage.
Reference to the superclass object.
First term voltage exponent for active power (Ep1). Used only when .staticLoadModelType = exponential.
Second term voltage exponent for active power (Ep2). Used only when .staticLoadModelType = exponential.
Third term voltage exponent for active power (Ep3). Used only when .staticLoadModelType = exponential.
First term voltage exponent for reactive power (Eq1). Used only when .staticLoadModelType = exponential.
Second term voltage exponent for reactive power (Eq2). Used only when .staticLoadModelType = exponential.
Third term voltage exponent for reactive power (Eq3). Used only when .staticLoadModelType = exponential.
First term voltage coefficient for active power (Kp1). Not used when .staticLoadModelType = constantZ.
Second term voltage coefficient for active power (Kp2). Not used when .staticLoadModelType = constantZ.
Third term voltage coefficient for active power (Kp3). Not used when .staticLoadModelType = constantZ.
Frequency coefficient for active power (Kp4). Must be non-zero when .staticLoadModelType = ZIP2. Not used for all other values of .staticLoadModelType.
Frequency deviation coefficient for active power (Kpf). Not used when .staticLoadModelType = constantZ.
First term voltage coefficient for reactive power (Kq1). Not used when .staticLoadModelType = constantZ.
Second term voltage coefficient for reactive power (Kq2). Not used when .staticLoadModelType = constantZ.
Third term voltage coefficient for reactive power (Kq3). Not used when .staticLoadModelType = constantZ.
Frequency coefficient for reactive power (Kq4). Must be non-zero when .staticLoadModelType = ZIP2. Not used for all other values of .staticLoadModelType.
Frequency deviation coefficient for reactive power (Kqf). Not used when .staticLoadModelType = constantZ.
Type of static load model. Typical Value = constantZ.
Aggregate load to which this aggregate static load belongs.
Load whose dynamic behaviour is described by a user-defined model.
Load whose dynamic behaviour is described by a user-defined model.
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Allows definition of reliablity areas (eg load pockets) within the ISO/RTO
Allows definition of reliablity areas (eg load pockets) within the ISO/RTO
Reference to the superclass object.
undocumented
The place, scene, or point of something where someone or something has been, is, and/or will be at a given moment in time.
The place, scene, or point of something where someone or something has been, is, and/or will be at a given moment in time. It can be defined with one or more postition points (coordinates) in a given coordinate system.
Reference to the superclass object.
(if applicable) Direction that allows field crews to quickly find a given asset. For a given location, such as a street address, this is the relative direction in which to find the asset. For example, a streetlight may be located at the 'NW' (northwest) corner of the customer's site, or a usage point may be located on the second floor of an apartment building.
Electronic address.
(if applicable) Reference to geographical information source, often external to the utility.
Main address of the location.
Phone number.
Additional phone number.
Secondary address of the location. For example, PO Box address may have different ZIP code than that in the 'mainAddress'.
Status of this location.
Classification by utility's corporate standards and practices, relative to the location itself (e.g., geographical, functional accounting, etc., not a given property that happens to exist at that location).
Coordinate system used to describe position points of this location.
undocumented
A grant provides a right, as defined by type, for a parcel of land.
A grant provides a right, as defined by type, for a parcel of land. Note that the association to Location, Asset, Organisation, etc. for the Grant is inherited from Agreement, a type of Document.
Reference to the superclass object.
Property related information that describes the Grant's land parcel. For example, it may be a deed book number, deed book page number, and parcel number.
Land property this location grant applies to.
RT only and is published on 5 minute intervals for the previous RT time interval results.
RT only and is published on 5 minute intervals for the previous RT time interval results.
Reference to the superclass object.
Provides the MW loss for RUC Zones, subcontrol areas, and the total loss.
Provides the MW loss for RUC Zones, subcontrol areas, and the total loss.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
LossProfile is associated with an EnerrgyTransaction and must be completely contained within the time frame of the EnergyProfile associated with this EnergyTransaction.
LossProfile is associated with an EnerrgyTransaction and must be completely contained within the time frame of the EnergyProfile associated with this EnergyTransaction.
Reference to the superclass object.
An EnergyTransaction may have a LossProfile.
Part of the LossProfile for an EnergyTransaction may be a loss for a TransmissionProvider. If so, the TransmissionProvider must be one of the participating entities in the EnergyTransaction.
Loss sensitivity applied to a ConnectivityNode for a given time interval.
Loss sensitivity applied to a ConnectivityNode for a given time interval.
Reference to the superclass object.
Loss penalty factor. Defined as: 1 / ( 1 - Incremental Transmission Loss); with the Incremental Transmission Loss expressed as a plus or minus value. The typical range of penalty factors is (0,9 to 1,1).
undocumented
Model of results of Market Power tests, and possible mitigation.
Model of results of Market Power tests, and possible mitigation. Interval based
Reference to the superclass object.
undocumented
undocumented
undocumented
Model of results of Market Power tests, gives status of resource for the associated interval
Model of results of Market Power tests, gives status of resource for the associated interval
Reference to the superclass object.
Interval Test Status 'N' - not applicable
undocumented
undocumented
Provides a reference to the Market Power Mitigation test identifiers and methods for the results of the DA or RT markets.
Provides a reference to the Market Power Mitigation test identifiers and methods for the results of the DA or RT markets. Specific data is the test identifier (Price, Conduct, or Impact) and the test method (System MPM, Local MPM, Alternate System MPM, or Alternate Local MPM).
Reference to the superclass object.
Nature of threshold data: 'M' - Mitigation threshold 'R' - Reporting threshold
1 - Global Price Test 2 - Global Conduct Test 3 - Global Impact Test 4 - Local Price Test 5 - Local Conduct Test 6 - Local Impact Test
The method of performing the market power monitoring. Examples are Normal (default) thresholds or Alternate thresholds.
Provides the outcome and margin percent (as appropriate) result data for the MPM tests.
Provides the outcome and margin percent (as appropriate) result data for the MPM tests. There are relationships to Zone for Designated Congestion Area Tests, CurveSchedData for bid segment tests, to the SubControlArea for the system wide level tests, and Pnodes for the LMPM impact tests.
Reference to the superclass object.
Used to show the Margin % result of the Impact test
The results of the test. For the Price, Impact, and Conduct tests, typical values are NA, Pass, Fail, Disable, or Skip.
undocumented
undocumented
undocumented
Market Power Mitigation (MPM) test thresholds for resource as well as designated congestion areas (DCAs)
Market Power Mitigation (MPM) test thresholds for resource as well as designated congestion areas (DCAs)
Reference to the superclass object.
Market Type (DAM, RTM)
Price Threshold in %
Price Threshold in $/MW
undocumented
undocumented
Metered Sub-System aggregation of MSS Zones.
Metered Sub-System aggregation of MSS Zones.
Reference to the superclass object.
Charge for Emission Costs, Start Up Costs, or Minimum Load Costs.
end effective date
MSS Load Following may select Net vs. Gross settlement. Net Settlement requires the net Demand settled at the MSS LAP and Net Supply needs to settle at the equivalent to the weighted average price of the MSS generation. Gross load will be settled at the System LAP and the Gross supply will be settled at the LMP. MSS Aggregation that elects gross settlement shall have to identify if its resources are Load Following or not.
Provides an indication if losses are to be ignored for this zone. Also refered to as Exclude Marginal Losses.
Provides an indication if marginal losses are to be ignored for this zone.
Indication that this particular MSSA participates in the Load Following function.
Indicates that RUC will be procured by the ISO or self provided.
start effective date
undocumented
Model to define a zone within a Metered Sub System
Model to define a zone within a Metered Sub System
Reference to the superclass object.
Provides an indication if losses are to be ignored for this metered subsystem zone.
This is the default loss factor for the Metered Sub-System (MSS) zone. The actual losses are calculated during the RT market.
Metered Sub-System (MSS) Load Following may select Net vs. Gross settlement. Net Settlement requires the net Demand settled at the Metered Sub-Sustem (MSS) Load Aggregation Point (LAP) and Net Supply needs to settle at the equivalent to the weighted average price of the MSS generation. Gross load will be settled at the System LAP and the Gross supply will be settled at the LMP. MSS Aggregation that elects gross settlement shall have to identify if its resources are Load Following or not.
undocumented
Maximum MW and optionally Minimum MW (Y1 and Y2, respectively)
Maximum MW and optionally Minimum MW (Y1 and Y2, respectively)
Reference to the superclass object.
undocumented
Organisation that maintains assets.
Organisation that maintains assets.
Reference to the superclass object.
The result of a maintenance activity, a type of Procedure, for a given attribute of an asset.
The result of a maintenance activity, a type of Procedure, for a given attribute of an asset.
Reference to the superclass object.
Condition of asset just following maintenance procedure.
Description of the condition of the asset just prior to maintenance being performed.
Code for the type of maintenance performed.
Location where to perform maintenance work.
Location where to perform maintenance work.
Reference to the superclass object.
(if applicable) Name, identifier, or description of the block in which work is to occur.
(if applicable) Name, identifier, or description of the lot in which work is to occur.
The names of streets at the nearest intersection to work area.
(if applicable) Name, identifier, or description of the subdivision in which work is to occur.
A Major Charge Group is the same as Invocie Type which provides the highest level of grouping for charge types configration.
A Major Charge Group is the same as Invocie Type which provides the highest level of grouping for charge types configration. Examples as Market, FERC, RMR,
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
Revision number for the major charge group
undocumented
undocumented
undocumented
A MajorChargeGroup can have 0-n ChargeType. A ChargeType can associate to 0-n MajorChargeGroup.
Organisation that manufactures asset products.
Organisation that manufactures asset products.
Reference to the superclass object.
Market (e.g.
Market (e.g. Day Ahead Market, RealTime Market) with a description of the the Market operation control parameters.
Reference to the superclass object.
Market ending time - actual market end
Market starting time - actual market start
True if daylight savings time (DST) is in effect.
Market end time.
Local time zone.
Market start time.
Market Status 'OPEN', 'CLOSED', 'CLEARED', 'BLOCKED'
Trading time interval length.
Market trading date
Trading period that describes the market, possibilities could be for an Energy Market: Day Hour For a CRR Market: Year Month Season
This class represent the actual instance of an event.
This class represent the actual instance of an event.
Reference to the superclass object.
Description of the event.
Actual event ID.
Start time of the event.
Market run triggered by this actual event. For example, the DA run is triggered by the actual open bid submission event and terminated by the actual close bid submission event.
Planned event executed by this actual event.
An identification or eventually the contents of an agreement between two or more parties.
An identification or eventually the contents of an agreement between two or more parties.
Reference to the superclass object.
Market case clearing results are posted for a given settlement period.
Market case clearing results are posted for a given settlement period.
Reference to the superclass object.
Settlement period: 'DA - Bid-in' 'DA - Reliability' 'DA - Amp1' 'DA - Amp2' 'RT - Ex-Ante' 'RT - Ex-Post' 'RT - Amp1' 'RT - Amp2'
Last time and date clearing results were manually modified.
Bid clearing results posted time and date.
Electronic document containing the information necessary to satisfy a given business process set of requirements.
Electronic document containing the information necessary to satisfy a given business process set of requirements.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
The identification of an entity where energy products are measured or computed.
The identification of an entity where energy products are measured or computed.
Reference to the superclass object.
Aggregation of market information relative for a specific time interval.
Aggregation of market information relative for a specific time interval.
Reference to the superclass object.
The end of the time interval for which requirement is defined.
The start of the time interval for which requirement is defined.
undocumented
undocumented
A roll up of invoice line items.
A roll up of invoice line items. The whole invoice has a due date and amount to be paid, with information such as customer, banks etc. being obtained through associations. The invoice roll up is based on individual line items that each contain amounts and descriptions for specific services or products.
Reference to the superclass object.
Total amount due on this invoice based on line items and applicable adjustments.
Kind of media by which the CustomerBillingInfo was delivered.
Calculated date upon which the Invoice amount is due.
Kind of invoice (default is 'sales').
Date on which the customer billing statement/invoice was printed/mailed.
True if payment is to be paid by a Customer to accept a particular ErpQuote (with associated Design) and have work initiated, at which time an associated ErpInvoice should automatically be generated. EprPayment.subjectStatus satisfies terms specificed in the ErpQuote.
Number of an invoice to be reference by this invoice.
Date and time when the invoice is issued.
Type of invoice transfer.
An individual line item on an invoice.
An individual line item on an invoice.
Reference to the superclass object.
Bill period for the line item.
General Ledger account code, shall be a valid combination.
Date and time line item will be posted to the General Ledger.
Kind of line item.
Amount due for this line item.
Line item number on invoice statement.
Version number of the bill run.
Net line item charge amount.
Previous line item charge amount.
undocumented
undocumented
undocumented
In accounting transactions, a ledger is a book containing accounts to which debits and credits are posted from journals, where transactions are initially recorded.
In accounting transactions, a ledger is a book containing accounts to which debits and credits are posted from journals, where transactions are initially recorded. Journal entries are periodically posted to the ledger. Ledger Actual represents actual amounts by account within ledger within company or business area. Actual amounts may be generated in a source application and then loaded to a specific ledger within the enterprise general ledger or budget application.
Reference to the superclass object.
Details of an individual entry in a ledger, which was posted from a journal on the posted date.
Details of an individual entry in a ledger, which was posted from a journal on the posted date.
Reference to the superclass object.
Account identifier for this entry.
Kind of account for this entry.
The amount of the debit or credit for this account.
Date and time this entry was posted to the ledger.
Status of ledger entry.
Date and time journal entry was recorded.
undocumented
undocumented
The condition or position of an object with regard to its standing.
The condition or position of an object with regard to its standing.
Reference to the superclass object.
The coded condition or position of an object with regard to its standing.
undocumented
An identification of a party acting in a electricity market business process.
An identification of a party acting in a electricity market business process. This class is used to identify organizations that can participate in market management and/or market operations.
Reference to the superclass object.
undocumented
General purpose information for name and other information to contact people.
General purpose information for name and other information to contact people.
Reference to the superclass object.
Category of this person relative to utility operations, classified according to the utility's corporate standards and practices. Examples include employee, contractor, agent, not affiliated, etc.
Alternate Electronic address.
Primary Electronic address.
Person's first name.
Unique identifier for person relative to its governing authority, for example a federal tax identifier (such as a Social Security number in the United States).
Landline phone number.
Person's last (family, sir) name.
Middle name(s) or initial(s).
Mobile phone number.
A prefix or title for the person's name, such as Miss, Mister, Doctor, etc.
Special service needs for the person (contact) are described; examples include life support, etc.
undocumented
A suffix for the person's name, such as II, III, etc.
The user name for the person; required to log in.
This class identifies a set of planned markets.
This class identifies a set of planned markets. This class is a container of these planned markets
Reference to the superclass object.
Description of the planned market.
Planned market identifier.
Name of the planned market.
Planned market trading day.
A product traded by an RTO (e.g.
A product traded by an RTO (e.g. energy, 10 minute spinning reserve). Ancillary service product examples include:Regulation UpRegulation DnSpinning ReserveNon-Spinning ReserveOperating Reserve
Reference to the superclass object.
Market product type examples: EN (Energy) RU (Regulation Up) RD (Regulation Dn) SR (Spinning Reserve) NR (Non-Spinning Reserve) RC (RUC)
Ramping time interval for the specific market product type specified by marketProductType attribute. For example, if marketProductType = EN (from enumeration MarketProductType), then the rampInterval is the ramping time interval for Energy.
undocumented
undocumented
Certain skills are required and shall be certified in order for a person (typically a member of a crew) to be qualified to work on types of equipment.
Certain skills are required and shall be certified in order for a person (typically a member of a crew) to be qualified to work on types of equipment.
Reference to the superclass object.
Effective date of the privilege, terminate date of the privilege, or effective date of the application for the organization
This is the terminate date of the application for the organization The specific organization can no longer access the application as of the terminate date
Qualification identifier.
The status of the privilege. Shows the status of the user�s qualification.
This is the name of the status of the qualification and is used to display the status of the user's or organization's status.
A specialized class of AggregatedNode type.
A specialized class of AggregatedNode type. Defines the MarketRegions. Regions could be system Market Regions, Energy Regions or Ancillary Service Regions.
Reference to the superclass object.
Provides all Region Ancillary Service results for the DA and RT markets.
Provides all Region Ancillary Service results for the DA and RT markets. The specific data is commodity type (Regulation Up, Regulation Down, Spinning Reserve, Non-spinning Reserve, or Total Up reserves) based for the cleared MW, cleared price, and total capacity required for the region.
Reference to the superclass object.
Cleared generation Value in MW. For AS, this value is clearedMW = AS Total. For AS, clearedMW - selfScheduleMW = AS Procured
Marginal Price ($/MW) for the commodity (Energy, Regulation Up, Regulation Down, Spinning Reserve, or Non-spinning reserve) based on the pricing run.
Dispatchable MW for Combustion units.
Dispatchable MW for Hydro units.
Dispatch rate in MW/minutes.
Dispatchable MW for Steam units.
Imbalance Energy Bias (MW) by Time Period (5' only)
Locational AS Flags indicating whether the Upper or Lower Bound limit of the AS regional procurment is binding
The "Lumpy Flag"(Y/N) indicates whether the resource that sets the price is a lumpy generator by hour over the time horizon. Only applicable for the Day Ahead Market
Region requirement maximum limit
Region requirement minimum limit
Region requirement maximum limit
Region requirement minimum limit
Aof AS, selfScheduleMW = AS Self-Provided
undocumented
undocumented
undocumented
This class holds elements that are single values for the entire market time horizon.
This class holds elements that are single values for the entire market time horizon. That is, for the Day Ahead market, there is 1 value for each element, not hourly based. Is a summary of the market run
Reference to the superclass object.
Total AS Cost (i.e., payment) ($) over the time horizon
Global Contingent Operating Reserve Availability Indicator (Yes/No)
Total Energy Cost ($) over the time horizon
Total Minimum Load Cost ($) over the time horizon
Total Start-up Cost ($) over the time horizon
Total Cost (Energy + AS) cost ($) by over the time horizon
The total RUC capacity cost for this interval
undocumented
The external intended behaviour played by a party within the electricity market.
The external intended behaviour played by a party within the electricity market.
Reference to the superclass object.
Defined using an enumerated list of types of market roles for use when a finite list of types are desired.
Status of the market role.
The kind of market roles that can be played by parties for given domains within the electricity market. Types are flexible using dataType of string for free-entry of role types.
undocumented
This class represent an actual instance of a planned market.
This class represent an actual instance of a planned market. For example, a Day Ahead market opens with the Bid Submission, ends with the closing of the Bid Submission. The market run represent the whole process. MarketRuns can be defined for markets such as Day Ahead Market, Real Time Market, Hour Ahead Market, Week Ahead Market,...
Reference to the superclass object.
The execution type; Day Ahead, Intra Day, Real Time Pre-Dispatch, Real Time Dispatch
Approved time for case. Identifies the time that the dispatcher approved a specific real time unit dispatch case
Set to true when the plan is approved by authority and becomes the official plan for the day ahead market. Identifies the approved case for the market for the specified time interval.
The end time defined as the end of the market, market end time.
An identification that defines the attributes of the Market. In todays terms: Market Type: DA, RTM, Trade Date: 1/25/04, Trade Hour: 1-25
A unique identifier that differentiates the different runs of the same Market ID. More specifically, if the market is re-opened and re-closed and rerun completely, the first set of results and the second set of results produced will have the same Market ID but will have different Market Run IDs since the multiple run is for the same market.
The start time defined as the beginning of the market, market start time.
The market type, Day Ahead Market or Real Time Market.
This is the state of market run activitie as reported by market systems to the market definition services.
This is the state controlled by market defintion service. possible values could be but not limited by: Open, Close.
undocumented
A planned market could have multiple market runs for the reason that a planned market could have a rerun.
Signifies an event to trigger one or more activities, such as reading a meter, recalculating a bill, requesting work, when generating units shall be scheduled for maintenance, when a transformer is scheduled to be refurbished, etc.
Signifies an event to trigger one or more activities, such as reading a meter, recalculating a bill, requesting work, when generating units shall be scheduled for maintenance, when a transformer is scheduled to be refurbished, etc.
Reference to the superclass object.
Category of scheduled event.
Duration of the scheduled event, for example, the time to ramp between values.
undocumented
undocumented
Proficiency level of a craft, which is required to operate or maintain a particular type of asset and/or perform certain types of work.
Proficiency level of a craft, which is required to operate or maintain a particular type of asset and/or perform certain types of work.
Reference to the superclass object.
Interval between the certification and its expiry.
Date and time the skill became effective.
Level of skill for a Craft.
undocumented
undocumented
A statement is a roll up of statement line items.
A statement is a roll up of statement line items. Each statement along with its line items provide the details of specific charges at any given time. Used by Billing and Settlement
Reference to the superclass object.
The end of a bill period.
The version number of previous statement (in the case of true up).
The start of a bill period.
The date of which Settlement is run.
The date of which this statement is issued.
An individual line item on a statement.
An individual line item on a statement.
Reference to the superclass object.
Current settlement amount.
Current ISO settlement amount.
Current ISO settlement quantity.
Current settlement price.
Current settlement quantity, subject to the UOM.
The date of which the settlement is run.
The number of intervals.
Net settlement amount.
Net ISO settlement amount.
Net ISO settlement quantity.
Net settlement price.
Net settlement quantity, subject to the UOM.
Previous settlement amount.
Previous ISO settlement amount.
Previous ISO settlement quantity.
Previous settlement quantity, subject to the UOM.
Previous settlement price.
The unit of measure for the quantity element of the line item.
undocumented
undocumented
undocumented
undocumented
Matches buyers and sellers, and secures transmission (and other ancillary services) needed to complete the energy transaction.
Matches buyers and sellers, and secures transmission (and other ancillary services) needed to complete the energy transaction.
Reference to the superclass object.
The physical consumable supply used for work and other purposes.
The physical consumable supply used for work and other purposes. It includes items such as nuts, bolts, brackets, glue, etc.
Reference to the superclass object.
Quantity of material used.
undocumented
undocumented
The maximum Startup costs and time as a function of down time.
The maximum Startup costs and time as a function of down time. Relationship between unit startup cost (Y1-axis) vs. unit elapsed down time (X-axis). This is used to validate the information provided in the Bid.
Reference to the superclass object.
A Measurement represents any measured, calculated or non-measured non-calculated quantity.
A Measurement represents any measured, calculated or non-measured non-calculated quantity. Any piece of equipment may contain Measurements, e.g. a substation may have temperature measurements and door open indications, a transformer may have oil temperature and tank pressure measurements, a bay may contain a number of power flow measurements and a Breaker may contain a switch status measurement.
Reference to the superclass object.
Specifies the type of measurement. For example, this specifies if the measurement represents an indoor temperature, outdoor temperature, bus voltage, line flow, etc.
Indicates to which phases the measurement applies and avoids the need to use 'measurementType' to also encode phase information (which would explode the types). The phase information in Measurement, along with 'measurementType' and 'phases' uniquely defines a Measurement for a device, based on normal network phase. Their meaning will not change when the computed energizing phasing is changed due to jumpers or other reasons.
The unit multiplier of the measured quantity.
The unit of measure of the measured quantity.
undocumented
The power system resource that contains the measurement.
One or more measurements may be associated with a terminal in the network.
Result of a calculation of one or more measurement.
Result of a calculation of one or more measurement.
Reference to the superclass object.
Calculation operation executed on the operants.
Input to measurement calculation.
Input to measurement calculation. Support Analog, Discrete and Accumulator.
Reference to the superclass object.
If true, use the absolute value for the calculation.
Positive number that defines the order of the operant in the calculation. 0 = default. The order is not relevant (e.g. summation).
undocumented
undocumented
The current state for a measurement.
The current state for a measurement. A state value is an instance of a measurement from a specific source. Measurements can be associated with many state values, each representing a different source for the measurement.
Reference to the superclass object.
undocumented
The limit, expressed as a percentage of the sensor maximum, that errors will not exceed when the sensor is used under reference conditions.
The time when the value was last updated
undocumented
A MeasurementValue has a MeasurementValueQuality associated with it.
A reference to the type of source that updates the MeasurementValue, e.g. SCADA, CCLink, manual, etc. User conventions for the names of sources are contained in the introduction to IEC 61970-301.
Link to the physical telemetered point associated with this measurement.
Measurement quality flags.
Measurement quality flags. Bits 0-10 are defined for substation automation in draft IEC 61850 part 7-3. Bits 11-15 are reserved for future expansion by that document. Bits 16-31 are reserved for EMS applications.
Reference to the superclass object.
A MeasurementValue has a MeasurementValueQuality associated with it.
MeasurementValueSource describes the alternative sources updating a MeasurementValue.
MeasurementValueSource describes the alternative sources updating a MeasurementValue. User conventions for how to use the MeasurementValueSource attributes are described in the introduction to IEC 61970-301.
Reference to the superclass object.
Mechanical load model type 1.
Mechanical load model type 1.
Reference to the superclass object.
Speed squared coefficient (a).
Speed coefficient (b).
Speed to the exponent coefficient (d).
Exponent (e).
Mechanical load function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Mechanical load function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Asynchronous machine model with which this mechanical load model is associated.
Synchronous machine model with which this mechanical load model is associated.
Mechanical load function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Mechanical load function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
A substance that either (1) provides the means of transmission of a force or effect, such as hydraulic fluid, or (2) is used for a surrounding or enveloping substance, such as oil in a transformer or circuit breaker.
A substance that either (1) provides the means of transmission of a force or effect, such as hydraulic fluid, or (2) is used for a surrounding or enveloping substance, such as oil in a transformer or circuit breaker.
Reference to the superclass object.
Kind of this medium.
The volume of the medium specified for this application. Note that the actual volume is a type of measurement associated witht the asset.
undocumented
undocumented
The operating account controlled by merchant agreement, against which the vendor may vend tokens or receipt payments.
The operating account controlled by merchant agreement, against which the vendor may vend tokens or receipt payments. Transactions via vendor shift debit the account and bank deposits via bank statement credit the account.
Reference to the superclass object.
The current operating balance of this account.
The balance of this account after taking into account any pending debits from VendorShift.merchantDebitAmount and pending credits from BankStatement.merchantCreditAmount or credits (see also BankStatement attributes and VendorShift attributes).
Merchant agreement that instantiated this merchant account.
All transactors this merchant account is registered with.
A formal controlling contractual agreement between supplier and merchant, in terms of which the merchant is authorised to vend tokens and receipt payments on behalf of the supplier.
A formal controlling contractual agreement between supplier and merchant, in terms of which the merchant is authorised to vend tokens and receipt payments on behalf of the supplier. The merchant is accountable to the supplier for revenue collected at point of sale.
Reference to the superclass object.
Physical asset that performs the metering role of the usage point.
Physical asset that performs the metering role of the usage point. Used for measuring consumption and detection of events.
Reference to the superclass object.
Meter form designation per ANSI C12.10 or other applicable standard. An alphanumeric designation denoting the circuit arrangement for which the meter is applicable and its specific terminal arrangement.
Multiplier applied at the meter.
Multiplier applied at the meter.
Reference to the superclass object.
Kind of multiplier.
Multiplier value.
Meter applying this multiplier.
Set of values obtained from the meter.
Set of values obtained from the meter.
Reference to the superclass object.
If true, this meter reading is the meter reading for which other coincident meter readings are requested or provided.
Date and time interval of the data items contained within this meter reading.
(could be deprecated in the future) Customer agreement for this meter reading.
Meter providing this reading.
Usage point from which this meter reading (set of values) has been obtained.
Work involving meters.
Work involving meters.
Reference to the superclass object.
Meter on which this non-replacement work is performed.
Old meter replaced by this work.
Usage point to which this meter service work applies.
A metered subsystem
A metered subsystem
Reference to the superclass object.
undocumented
A specification of the metering requirements for a particular point within a network.
A specification of the metering requirements for a particular point within a network.
Reference to the superclass object.
Reason for this metrology requirement being specified.
All usage points having this metrology requirement.
Various cost items that are not associated with compatible units.
Various cost items that are not associated with compatible units. Examples include rental equipment, labor, materials, contractor costs, permits - anything not covered in a CU.
Reference to the superclass object.
This drives the accounting treatment for this misc. item.
The cost per unit for this misc. item.
The cost type for accounting, such as material, labor, vehicle, contractor, equipment, overhead.
External reference identifier (e.g. purchase order number, serial number) .
The quantity of the misc. item being assigned to this location.
undocumented
undocumented
undocumented
undocumented
Mitigated bid results posted for a given settlement period.
Mitigated bid results posted for a given settlement period.
Reference to the superclass object.
undocumented
Model of market power mitigation through reference or mitigated bids.
Model of market power mitigation through reference or mitigated bids. Interval based.
Reference to the superclass object.
Model of mitigated bid.
Model of mitigated bid. Indicates segment of piece-wise linear bid, that has been mitigated
Reference to the superclass object.
undocumented
Mitigated bid segment MW value
Mitigated Bid Segment Number
undocumented
undocumented
Subclass of IEC61970:Wires:ACLineSegment
Subclass of IEC61970:Wires:ACLineSegment
Reference to the superclass object.
undocumented
undocumented
Subclass of IEC61968: Common:ActivityRecord
Subclass of IEC61968: Common:ActivityRecord
Reference to the superclass object.
Subclass of IEC61970:Meas:AnalogLimit
Subclass of IEC61970:Meas:AnalogLimit
Reference to the superclass object.
true if limit exceeded
The type of limit the value represents Branch Limit Types: Short Term Medium Term Long Term Voltage Limits: High Low
Subclass of IEC61970:Meas:AnalogLimitSet
Subclass of IEC61970:Meas:AnalogLimitSet
Reference to the superclass object.
Rating set numbers
Subclass of IEC61970:Meas:AnalogValue
Subclass of IEC61970:Meas:AnalogValue
Reference to the superclass object.
Subclass of Production: CombinedCyclePlant from IEC61970 package.
Subclass of Production: CombinedCyclePlant from IEC61970 package. A set of combustion turbines and steam turbines where the exhaust heat from the combustion turbines is recovered to make steam for the steam turbines, resulting in greater overall plant efficiency
Reference to the superclass object.
undocumented
Subclass of IEC61970:Core:ConductingEquipment
Subclass of IEC61970:Core:ConductingEquipment
Reference to the superclass object.
Subclass of IEC61970:Topology:ConnectivityNode
Subclass of IEC61970:Topology:ConnectivityNode
Reference to the superclass object.
end effective date
start effective date
undocumented
undocumented
undocumented
Subclass of IEC61970:Contingency
Subclass of IEC61970:Contingency
Reference to the superclass object.
load change flag Flag that indicates whether load rollover and load pickup should be processed for this contingency
ltc enable flag Flag that indicates if LTCs regulate voltage during the solution of the contingency
Participation Factor flag An indication which set of generator participation factors should be used to re-allocate generation in this contingency
sceening flag for outage Flag that indicated whether screening is bypassed for the contingency
undocumented
undocumented
Market subclass of IEC61970:ControlArea
Market subclass of IEC61970:ControlArea
Reference to the superclass object.
Subclass of IEC61970:Meas:DiscreteValue
Subclass of IEC61970:Meas:DiscreteValue
Reference to the superclass object.
Subclass of IEC61970:Wires:EnergyConsumer
Subclass of IEC61970:Wires:EnergyConsumer
Reference to the superclass object.
undocumented
Subclass of IEC61970:Production:GeneratingUnit
Subclass of IEC61970:Production:GeneratingUnit
Reference to the superclass object.
undocumented
Subclass of IEC61970: Generation: Production:HeatRateCurve
Subclass of IEC61970: Generation: Production:HeatRateCurve
Reference to the superclass object.
undocumented
undocumented
Subclass for IEC61970:Wires:Line
Subclass for IEC61970:Wires:Line
Reference to the superclass object.
undocumented
Subclass of IEC61970:LoadModel: LoadArea
Subclass of IEC61970:LoadModel: LoadArea
Reference to the superclass object.
Subclass of IEC61970:Meas:Measurement
Subclass of IEC61970:Meas:Measurement
Reference to the superclass object.
A measurement is made on the B side of a tie point
A measurement is made on the A side of a tie point
undocumented
Subclass of IEC61968:Core2:TopLevel:Organisation
Subclass of IEC61968:Core2:TopLevel:Organisation
Reference to the superclass object.
Flag to indicate creditworthiness (Y, N)
Date that the organisation becomes creditworthy.
end effective date
Indication of the last time this Organization information was modified.
Organisation (internal) ID
Organisation qualification status, Qualified, Not Qualified, or Disqualified
start effective date
undocumented
The type of a power system resource.
The type of a power system resource.
Reference to the superclass object.
The coded type of a power system resource.
undocumented
Subclass of IEC61970:Wires:PowerTransformer
Subclass of IEC61970:Wires:PowerTransformer
Reference to the superclass object.
undocumented
undocumented
Subclass of IEC61970:Wires:SeriesCompensator
Subclass of IEC61970:Wires:SeriesCompensator
Reference to the superclass object.
undocumented
undocumented
Subclass of IEC61970:Wires:ShuntCompensator
Subclass of IEC61970:Wires:ShuntCompensator
Reference to the superclass object.
Subclass of IEC61970:Wires:Switch
Subclass of IEC61970:Wires:Switch
Reference to the superclass object.
Subclass of IEC61970:Wires:TapChanger
Subclass of IEC61970:Wires:TapChanger
Reference to the superclass object.
Subclass of IEC61970:Core:Terminal
Subclass of IEC61970:Core:Terminal
Reference to the superclass object.
This is the end date/time of the element eligibility for the flowgate.
This is the begin date/time of the element eligibility for the flowgate.
undocumented
Subclass of ThermalGeneratingUnit from Production Package in IEC61970.
Subclass of ThermalGeneratingUnit from Production Package in IEC61970.
Reference to the superclass object.
Subclass of IEC61968:Domain2:UserAttribute
Subclass of IEC61968:Domain2:UserAttribute
Reference to the superclass object.
A Modeling Authority is an entity responsible for supplying and maintaining the data defining a specific set of objects in a network model.
A Modeling Authority is an entity responsible for supplying and maintaining the data defining a specific set of objects in a network model.
Reference to the superclass object.
A Modeling Authority Set is a group of objects in a network model where the data is supplied and maintained by the same Modeling Authority.
A Modeling Authority Set is a group of objects in a network model where the data is supplied and maintained by the same Modeling Authority. This class is typically not included in instance data exchange as this information is tracked by other mechanisms in the exchange.
Reference to the superclass object.
A Modeling Authority set supplies and maintains the data for the objects in a Modeling Authority Set.
Interval between two times specified as mont and date.
Interval between two times specified as mont and date.
Reference to the superclass object.
End time of this interval.
Start time of this interval.
This class represents the zero sequence line mutual coupling.
This class represents the zero sequence line mutual coupling.
Reference to the superclass object.
Zero sequence mutual coupling shunt (charging) susceptance, uniformly distributed, of the entire line section.
Distance to the start of the coupled region from the first line's terminal having sequence number equal to 1.
Distance to the end of the coupled region from the first line's terminal with sequence number equal to 1.
Distance to the start of coupled region from the second line's terminal with sequence number equal to 1.
Distance to the end of coupled region from the second line's terminal with sequence number equal to 1.
Zero sequence mutual coupling shunt (charging) conductance, uniformly distributed, of the entire line section.
Zero sequence branch-to-branch mutual impedance coupling, resistance.
Zero sequence branch-to-branch mutual impedance coupling, reactance.
The starting terminal for the calculation of distances along the first branch of the mutual coupling. Normally MutualCoupling would only be used for terminals of AC line segments. The first and second terminals of a mutual coupling should point to different AC line segments.
The starting terminal for the calculation of distances along the second branch of the mutual coupling.
The Name class provides the means to define any number of human readable names for an object.
The Name class provides the means to define any number of human readable names for an object. A name is not to be used for defining inter-object relationships. For inter-object relationships instead use the object identification 'mRID'.
Reference to the superclass object.
Any free text that name the object.
Identified object that this name designates.
Type of this name.
Type of name.
Type of name. Possible values for attribute 'name' are implementation dependent but standard profiles may specify types. An enterprise may have multiple IT systems each having its own local name for the same object, e.g. a planning system may have different names from an EMS. An object may also have different names within the same IT system, e.g. localName as defined in CIM version 14. The definition from CIM14 is:
Reference to the superclass object.
Description of the name type.
Name of the name type.
Authority responsible for managing names of this type.
Authority responsible for creation and management of names of a given type; typically an organization or an enterprise system.
Authority responsible for creation and management of names of a given type; typically an organization or an enterprise system.
Reference to the superclass object.
Description of the name type authority.
Name of the name type authority.
No-load test results determine core admittance parameters.
No-load test results determine core admittance parameters. They include exciting current and core loss measurements from applying voltage to one winding. The excitation may be positive sequence or zero sequence. The test may be repeated at different voltages to measure saturation.
Reference to the superclass object.
Voltage applied to the winding (end) during test.
Exciting current measured from a positive-sequence or single-phase excitation test.
Exciting current measured from a zero-sequence open-circuit excitation test.
Losses measured from a positive-sequence or single-phase excitation test.
Losses measured from a zero-sequence excitation test.
Transformer end that current is applied to in this no-load test.
To be used only to constrain a quantity that cannot be associated with a terminal.
To be used only to constrain a quantity that cannot be associated with a terminal. For example, a registered generating unit that is not electrically connected to the network.
Reference to the superclass object.
undocumented
NonConformLoad represent loads that do not follow a daily load change pattern and changes are not correlated with the daily load change pattern.
NonConformLoad represent loads that do not follow a daily load change pattern and changes are not correlated with the daily load change pattern.
Reference to the superclass object.
Group of this ConformLoad.
Loads that do not follow a daily and seasonal load variation pattern.
Loads that do not follow a daily and seasonal load variation pattern.
Reference to the superclass object.
An active power (Y1-axis) and reactive power (Y2-axis) schedule (curves) versus time (X-axis) for non-conforming loads, e.g., large industrial load or power station service (where modeled).
An active power (Y1-axis) and reactive power (Y2-axis) schedule (curves) versus time (X-axis) for non-conforming loads, e.g., large industrial load or power station service (where modeled).
Reference to the superclass object.
The NonConformLoadGroup where the NonConformLoadSchedule belongs.
This document provides information for non-standard items like customer contributions (e.g., customer digs trench), vouchers (e.g., credit), and contractor bids.
This document provides information for non-standard items like customer contributions (e.g., customer digs trench), vouchers (e.g., credit), and contractor bids.
Reference to the superclass object.
The projected cost for this item.
A non linear shunt compensator has bank or section admittance values that differs.
A non linear shunt compensator has bank or section admittance values that differs.
Reference to the superclass object.
A per phase non linear shunt compensator has bank or section admittance values that differs.
A per phase non linear shunt compensator has bank or section admittance values that differs.
Reference to the superclass object.
A per phase non linear shunt compensator bank or section admittance value.
A per phase non linear shunt compensator bank or section admittance value.
Reference to the superclass object.
Positive sequence shunt (charging) susceptance per section
Positive sequence shunt (charging) conductance per section
The number of the section.
Non-linear shunt compensator phase owning this point.
A non linear shunt compensator bank or section admittance value.
A non linear shunt compensator bank or section admittance value.
Reference to the superclass object.
Positive sequence shunt (charging) susceptance per section
Zero sequence shunt (charging) susceptance per section
Positive sequence shunt (charging) conductance per section
Zero sequence shunt (charging) conductance per section
The number of the section.
Non-linear shunt compensator owning this point.
Notification time curve as a function of down time.
Notification time curve as a function of down time. Relationship between crew notification time (Y1-axis) and unit startup time (Y2-axis) vs. unit elapsed down time (X-axis).
Reference to the superclass object.
A nuclear generating unit.
A nuclear generating unit.
Reference to the superclass object.
Price of oil in monetary units
Price of oil in monetary units
Reference to the superclass object.
The average oil price at a defined fuel region.
undocumented
A crew is a group of people with specific skills, tools, and vehicles.
A crew is a group of people with specific skills, tools, and vehicles.
Reference to the superclass object.
Classification by utility's work management standards and practices.
All Assignments for this Crew.
undocumented
undocumented
undocumented
General purpose information for name and other information to contact people.
General purpose information for name and other information to contact people.
Reference to the superclass object.
undocumented
Utility-specific classification for this person, according to the utility's corporate standards and practices. Examples include employee, contractor, agent, not affiliated, etc.
undocumented
undocumented
undocumented
undocumented
Properties of switch assets.
Properties of switch assets.
Reference to the superclass object.
The maximum rms voltage that may be applied across an open contact without breaking down the dielectric properties of the switch in the open position.
True if switch has load breaking capabiity. Unless specified false, this is always assumed to be true for breakers and reclosers.
The highest value of current the switch can make at the rated voltage under specified operating conditions without suffering significant deterioration of its performance.
The lowest value of current that the switch can make, carry and break in uninterrupted duty at the rated voltage under specified operating conditions without suffering significant deterioration of its performance.
Number of poles (i.e. of current carrying conductors that are switched).
True if device is capable of being operated by remote control.
The highest value of current the switch can carry in the closed position at the rated voltage under specified operating conditions without suffering significant deterioration of its performance.
A set of tasks is required to implement a design.
A set of tasks is required to implement a design.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
A request for other utilities to mark their underground facilities prior to commencement of construction and/or maintenance.
A request for other utilities to mark their underground facilities prior to commencement of construction and/or maintenance.
Reference to the superclass object.
True if explosives have been or are planned to be used.
True if work location has been marked, for example for a dig area.
Instructions for marking a dig area, if applicable.
Contracts for services offered commercially.
Contracts for services offered commercially.
Reference to the superclass object.
Open-circuit test results verify winding turn ratios and phase shifts.
Open-circuit test results verify winding turn ratios and phase shifts. They include induced voltage and phase shift measurements on open-circuit windings, with voltage applied to the energised end. For three-phase windings, the excitation can be a positive sequence (the default) or a zero sequence.
Reference to the superclass object.
Tap step number for the energised end of the test pair.
Voltage applied to the winding (end) during test.
Tap step number for the open end of the test pair.
Voltage measured at the open-circuited end, with the energised end set to rated voltage and all other ends open.
Phase shift measured at the open end with the energised end set to rated voltage and all other ends open.
Transformer end that current is applied to in this open-circuit test.
Transformer end measured for induced voltage and angle in this open-circuit test.
Result of bid validation against conditions that may exist on an interchange that becomes disconnected or is heavily discounted with respect the MW flow.
Result of bid validation against conditions that may exist on an interchange that becomes disconnected or is heavily discounted with respect the MW flow. This schedule is assocated with the hourly parameters in a resource bid.
Reference to the superclass object.
undocumented
An operator of multiple power system resource objects.
An operator of multiple power system resource objects. Note multple operating participants may operate the same power system resource object. This can be used for modeling jointly owned units where each owner operates as a contractual share.
Reference to the superclass object.
Specifies the operations contract relationship between a power system resource and a contract participant.
Specifies the operations contract relationship between a power system resource and a contract participant.
Reference to the superclass object.
Percentage operational ownership between the pair (power system resource and operatging participant) associated with this share. The total percentage ownership for a power system resource should add to 100%.
The operating participant having this share with the associated power system resource.
The power system resource to which the share applies.
Person role in the context of utility operations.
Person role in the context of utility operations.
Reference to the superclass object.
A value associated with a specific kind of limit.
A value associated with a specific kind of limit. The sub class value attribute shall be positive.
Reference to the superclass object.
The limit dependency models which are used to calculate this limit. If no limit dependencies are specified then the native limit value is used.
The limit set to which the limit values belong.
The limit type associated with this limit.
A set of limits associated with equipment.
A set of limits associated with equipment. Sets of limits might apply to a specific temperature, or season for example. A set of limits may contain different severities of limit levels that would apply to the same equipment. The set may contain limits of different types such as apparent power and current limits or high and low voltage limits that are logically applied together as a set.
Reference to the superclass object.
The equipment to which the limit set applies.
undocumented
The operational meaning of a category of limits.
The operational meaning of a category of limits.
Reference to the superclass object.
The nominal acceptable duration of the limit. Limits are commonly expressed in terms of the a time limit for which the limit is normally acceptable. The actual acceptable duration of a specific limit may depend on other local factors such as temperature or wind speed.
The direction of the limit.
undocumented
A document that can be associated with equipment to describe any sort of restrictions compared with the original manufacturer's specification or with the usual operational practice e.g.
A document that can be associated with equipment to describe any sort of restrictions compared with the original manufacturer's specification or with the usual operational practice e.g. temporary maximum loadings, maximum switching current, do not operate if bus couplers are open, etc. In the UK, for example, if a breaker or switch ever mal-operates, this is reported centrally and utilities use their asset systems to identify all the installed devices of the same manufacturer's type. They then apply operational restrictions in the operational systems to warn operators of potential problems. After appropriate inspection and maintenance, the operational restrictions may be removed.
Reference to the superclass object.
Interval during which this restriction is applied.
Restricted (new) value; includes unit of measure and potentially multiplier.
All equipments to which this restriction applies.
Asset model to which this restriction applies.
Lowered capability because of deterioration or inadequacy (sometimes referred to as derating or partial outage) or other kind of operational rating change.
Lowered capability because of deterioration or inadequacy (sometimes referred to as derating or partial outage) or other kind of operational rating change.
Reference to the superclass object.
Type of operational updated rating, e.g. a derate, a rerate or a return to normal.
Planned equipment outage with this updated rating.
One operational limit type scales values of another operational limit type when under the same operational limit set.
One operational limit type scales values of another operational limit type when under the same operational limit set. This applies to any operational limit assigned to the target operational limit type and without other limit dependency models.
Reference to the superclass object.
The percentage scaling of the source limit to compute the target limit. Applys to operational limits within an operaitonal limit set when both source and target operational limit types exist.
undocumented
undocumented
Control room operator.
Control room operator.
Reference to the superclass object.
Roles played between Organisations and other Organisations.
Roles played between Organisations and other Organisations. This includes role ups for ogranisations, cost centers, profit centers, regulatory reporting, etc.
Reference to the superclass object.
Identifiers of the organisation held by another organisation, such as a government agency (federal, state, province, city, county), financial institution (Dun and Bradstreet), etc.
This class models the allocation between asset owners and pricing nodes
This class models the allocation between asset owners and pricing nodes
Reference to the superclass object.
end effective date
Maximum MW for the Source/Sink for the Allocation
start effective date
undocumented
undocumented
This class model the ownership percent and type of ownership between resource and organisation
This class model the ownership percent and type of ownership between resource and organisation
Reference to the superclass object.
association type for the association between Organisation and Resource:
end effective date
Flag to indicate that the SC representing the Resource is the Master SC.
ownership percentage for each resource
start effective date
undocumented
undocumented
Organisation that might have roles as utility, contractor, supplier, manufacturer, customer, etc.
Organisation that might have roles as utility, contractor, supplier, manufacturer, customer, etc.
Reference to the superclass object.
Electronic address.
Phone number.
Additional phone number.
Postal address, potentially different than 'streetAddress' (e.g., another city).
Street address.
undocumented
Identifies a way in which an organisation may participate in the utility enterprise (e.g., customer, manufacturer, etc).
Identifies a way in which an organisation may participate in the utility enterprise (e.g., customer, manufacturer, etc).
Reference to the superclass object.
Organisation having this role.
Document describing details of an active or planned outage in a part of the electrical network.
Document describing details of an active or planned outage in a part of the electrical network. A non-planned outage may be created upon:
Reference to the superclass object.
Actual outage period; end of the period corresponds to the actual restoration time.
Date and time planned outage has been cancelled.
One or more causes of this outage. Note: At present, this is a free text; could be replaced with a separate associated class in case we have multiple causes (e.g. OutageCauseType, inheriting from IdentifiedObject).
Estimated outage period. The start of the period makes sense in case of a planned outage only, whereas the end of the period corresponds to the estimated restoration time in general.
True if planned, false otherwise (for example due to a breaker trip).
Summary counts of service points (customers) affected by this outage.
All equipments associated with this outage.
Incident reported in trouble call that results in this outage.
Outage schedule whose execution will result in this outage.
All usage points associated with this outage.
Document containing the definition of planned outages of equipment and/or service (delivery) points (sometimes referred to as customers).
Document containing the definition of planned outages of equipment and/or service (delivery) points (sometimes referred to as customers). It is used as specification for producing switching plans.
Reference to the superclass object.
Different from LimIEEEOEL, LimOEL2 has a fixed pickup threshold and reduces the excitation set-point by mean of non-windup integral regulator.
Different from LimIEEEOEL, LimOEL2 has a fixed pickup threshold and reduces the excitation set-point by mean of non-windup integral regulator. Irated is the rated machine excitation current (calculated from nameplate conditions: Vnom, Pnom, CosPhinom).
Reference to the superclass object.
Limit value of rated field current (IFDLIM). Typical Value = 1.05.
Gain Over excitation limiter (KOI). Typical Value = 0.1.
Maximum error signal (VOIMAX). Typical Value = 0.
Minimum error signal (VOIMIN). Typical Value = -9999.
The over excitation limiter model is intended to represent the significant features of OELs necessary for some large-scale system studies.
The over excitation limiter model is intended to represent the significant features of OELs necessary for some large-scale system studies. It is the result of a pragmatic approach to obtain a model that can be widely applied with attainable data from generator owners. An attempt to include all variations in the functionality of OELs and duplicate how they interact with the rest of the excitation systems would likely result in a level of application insufficient for the studies for which they are intended.
Reference to the superclass object.
OEL pickup/drop-out hysteresis (HYST). Typical Value = 0.03.
OEL timed field current limit (IFDLIM). Typical Value = 1.05.
OEL instantaneous field current limit (IFDMAX). Typical Value = 1.5.
OEL timed field current limiter pickup level (ITFPU). Typical Value = 1.05.
OEL cooldown gain (KCD). Typical Value = 1.
OEL ramped limit rate (KRAMP). Unit = PU/sec. Typical Value = 10.
Field voltage over excitation limiter.
Field voltage over excitation limiter.
Reference to the superclass object.
Low voltage point on the inverse time characteristic (EFD1). Typical Value = 1.1.
Mid voltage point on the inverse time characteristic (EFD2). Typical Value = 1.2.
High voltage point on the inverse time characteristic (EFD3). Typical Value = 1.5.
Desired field voltage (EFDDES). Typical Value = 0.9.
Rated field voltage (EFDRATED). Typical Value = 1.05.
Gain (KMX). Typical Value = 0.01.
Time to trip the exciter at the low voltage point on the inverse time characteristic (TIME1). Typical Value = 120.
Time to trip the exciter at the mid voltage point on the inverse time characteristic (TIME2). Typical Value = 40.
Time to trip the exciter at the high voltage point on the inverse time characteristic (TIME3). Typical Value = 15.
Low voltage limit (VLOW) (>0).
Field Voltage or Current overexcitation limiter designed to protect the generator field of an AC machine with automatic excitation control from overheating due to prolonged overexcitation.
Field Voltage or Current overexcitation limiter designed to protect the generator field of an AC machine with automatic excitation control from overheating due to prolonged overexcitation.
Reference to the superclass object.
Low voltage or current point on the inverse time characteristic (EFD1). Typical Value = 1.1.
Mid voltage or current point on the inverse time characteristic (EFD2). Typical Value = 1.2.
High voltage or current point on the inverse time characteristic (EFD3). Typical Value = 1.5.
Desired field voltage if m=F or field current if m=T (EFDDES). Typical Value = 1.
Rated field voltage if m=F or field current if m=T (EFDRATED). Typical Value = 1.05.
Gain (KMX). Typical Value = 0.002.
(m). true = IFD limiting false = EFD limiting.
Time to trip the exciter at the low voltage or current point on the inverse time characteristic (TIME1). Typical Value = 120.
Time to trip the exciter at the mid voltage or current point on the inverse time characteristic (TIME2). Typical Value = 40.
Time to trip the exciter at the high voltage or current point on the inverse time characteristic (TIME3). Typical Value = 15.
Low voltage limit (VLOW) (>0).
<font color="#0f0f0f">O</font>Overexcitation limiter function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
<font color="#0f0f0f">O</font>Overexcitation limiter function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Excitation system model with which this overexcitation limiter model is associated.
Overexcitation limiter system function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Overexcitation limiter system function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Overhead cost applied to work order.
Overhead cost applied to work order.
Reference to the superclass object.
Overhead code.
The overhead cost to be applied.
undocumented
Overhead wire data.
Overhead wire data.
Reference to the superclass object.
Ownership of e.g.
Ownership of e.g. asset.
Reference to the superclass object.
Share of this ownership.
Asset that is object of this ownership.
Asset owner that is subject in this ownership.
Power Factor or VAr controller Type I function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Power Factor or VAr controller Type I function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Excitation system model with which this Power Factor or VAr controller Type I model is associated.
Remote input signal used by this Power Factor or VAr controller Type I model.
Voltage adjuster model associated with this Power Factor or VA controller Type I model.
Power Factor or VAr controller Type I function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Power Factor or VAr controller Type I function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Power Factor or VAr controller Type II function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Power Factor or VAr controller Type II function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Excitation system model with which this Power Factor or VAr controller Type II is associated.
Power Factor or VAr controller Type II function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Power Factor or VAr controller Type II function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
The class represents IEEE PF Controller Type 1 which operates by moving the voltage reference directly.
The class represents IEEE PF Controller Type 1 which operates by moving the voltage reference directly. Reference: IEEE Standard 421.5-2005 Section 11.2.
Reference to the superclass object.
Overexcitation Flag (OVEX) true = overexcited false = underexcited.
PF controller time delay (TPFC). Typical Value = 5.
Minimum machine terminal current needed to enable pf/var controller (VITMIN).
Synchronous machine power factor (VPF).
PF controller dead band (VPFC_BW). Typical Value = 0.05.
PF controller reference (VPFREF).
Maximum machine terminal voltage needed for pf/var controller to be enabled (VVTMAX).
Minimum machine terminal voltage needed to enable pf/var controller (VVTMIN).
The class represents IEEE VAR Controller Type 1 which operates by moving the voltage reference directly.
The class represents IEEE VAR Controller Type 1 which operates by moving the voltage reference directly. Reference: IEEE Standard 421.5-2005 Section 11.3.
Reference to the superclass object.
Var controller time delay (TVARC). Typical Value = 5.
Synchronous machine power factor (VVAR).
Var controller dead band (VVARC_BW). Typical Value = 0.02.
Var controller reference (VVARREF).
Maximum machine terminal voltage needed for pf/var controller to be enabled (VVTMAX).
Minimum machine terminal voltage needed to enable pf/var controller (VVTMIN).
Power factor / Reactive power regulator.
Power factor / Reactive power regulator. This model represents the power factor or reactive power controller such as the Basler SCP-250. The controller measures power factor or reactive power (PU on generator rated power) and compares it with the operator's set point.
Reference to the superclass object.
Selector (J). true = control mode for reactive power false = control mode for power factor.
Reset gain (Ki).
Proportional gain (Kp).
Output limit (max).
Reference value of reactive power or power factor (Ref). The reference value is initialised by this model. This initialisation may override the value exchanged by this attribute to represent a plant operator's change of the reference setting.
The class represents IEEE PF Controller Type 2 which is a summing point type controller and makes up the outside loop of a two-loop system.
The class represents IEEE PF Controller Type 2 which is a summing point type controller and makes up the outside loop of a two-loop system. This controller is implemented as a slow PI type controller. The voltage regulator forms the inner loop and is implemented as a fast controller.
Reference to the superclass object.
Overexcitation or under excitation flag (EXLON) true = 1 (not in the overexcitation or underexcitation state, integral action is active) false = 0 (in the overexcitation or underexcitation state, so integral action is disabled to allow the limiter to play its role).
Integral gain of the pf controller (KI). Typical Value = 1.
Proportional gain of the pf controller (KP). Typical Value = 1.
Power factor reference (PFREF).
Maximum output of the pf controller (VCLMT). Typical Value = 0.1.
Voltage regulator reference (VREF).
Generator sensing voltage (VS).
The class represents IEEE VAR Controller Type 2 which is a summing point type controller.
The class represents IEEE VAR Controller Type 2 which is a summing point type controller. It makes up the outside loop of a two-loop system. This controller is implemented as a slow PI type controller, and the voltage regulator forms the inner loop and is implemented as a fast controller.
Reference to the superclass object.
Overexcitation or under excitation flag (EXLON) true = 1 (not in the overexcitation or underexcitation state, integral action is active) false = 0 (in the overexcitation or underexcitation state, so integral action is disabled to allow the limiter to play its role).
Integral gain of the pf controller (KI).
Proportional gain of the pf controller (KP).
Reactive power reference (QREF).
Maximum output of the pf controller (VCLMT).
Voltage regulator reference (VREF).
Generator sensing voltage (VS).
Event recording the change in operational status of a power system resource; may be for an event that has already occurred or for a planned activity.
Event recording the change in operational status of a power system resource; may be for an event that has already occurred or for a planned activity.
Reference to the superclass object.
Kind of event.
Power system resource that generated this event.
Classifying instances of the same class, e.g.
Classifying instances of the same class, e.g. overhead and underground ACLineSegments. This classification mechanism is intended to provide flexibility outside the scope of this standard, i.e. provide customisation that is non standard.
Reference to the superclass object.
Pressurized water reactor used as a steam supply to a steam turbine.
Pressurized water reactor used as a steam supply to a steam turbine.
Reference to the superclass object.
Cold leg feedback lag time constant.
Cold leg feedback lead time constant.
Cold leg feedback lead time constant.
Cold leg feedback gain 1.
Cold leg feedback gain 2.
Cold leg lag time constant.
Core heat transfer lag time constant.
Core heat transfer lag time constant.
Core neutronics effective time constant.
Core neutronics and heat transfer.
Feedback factor.
Hot leg lag time constant.
Hot leg steam gain.
Hot leg to cold leg gain.
Pressure control gain.
Steam flow feedback gain.
Steam pressure drop lag time constant.
Steam pressure feedback gain.
Throttle pressure factor.
Throttle pressure setpoint.
The version of dependencies description among top level subpackages of the combined CIM model.
The version of dependencies description among top level subpackages of the combined CIM model. This is not the same as the combined packages version.
Reference to the superclass object.
Date of last change to the main package dependencies in format YYYY-MM-DD. This is updated when the version attribute is updated.
The version of the main subpackages of the combined CIM model. The format is simply an integer. The version (and date) initial values should be updated any time the dependencies in the model change and require an actual change to the diagrams within this package.
PAN control used to issue action/command to PAN devices during a demand response/load control event.
PAN control used to issue action/command to PAN devices during a demand response/load control event.
Reference to the superclass object.
Appliance being controlled.
Used to define a maximum energy usage limit as a percentage of the client implementations specific average energy usage. The load adjustment percentage is added to 100% creating a percentage limit applied to the client implementations specific average energy usage. A -10% load adjustment percentage will establish an energy usage limit equal to 90% of the client implementations specific average energy usage. Each load adjustment percentage is referenced to the client implementations specific average energy usage. There are no cumulative effects.
Encoding of cancel control.
Timestamp when a canceling of the event is scheduled to start.
If true, a canceling of the event should start immediately.
Requested offset to apply to the normal cooling setpoint at the time of the start of the event. It represents a temperature change that will be applied to the associated cooling set point. The temperature offsets will be calculated per the local temperature in the thermostat. The calculated temperature will be interpreted as the number of degrees to be added to the cooling set point. Sequential demand response events are not cumulative. The offset shall be applied to the normal setpoint.
Requested cooling set point. Temperature set point is typically defined and calculated based on local temperature.
Level of criticality for the action of this control. The action taken by load control devices for an event can be solely based on this value, or in combination with other load control event fields supported by the device.
Maximum "on" state duty cycle as a percentage of time. For example, if the value is 80, the device would be in an "on" state for 80% of the time for the duration of the action.
Provides a mechanism to direct load control actions to groups of PAN devices. It can be used in conjunction with the PAN device types.
Requested offset to apply to the normal heating setpoint at the time of the start of the event. It represents a temperature change that will be applied to the associated heating set point. The temperature offsets will be calculated per the local temperature in the thermostat. The calculated temperature will be interpreted as the number of degrees to be subtracted from the heating set point. Sequential demand response events are not cumulative. The offset shall be applied to the normal setpoint.
Requested heating set point. Temperature set point is typically defined and calculated based on local temperature.
PAN action/command used to issue the displaying of text messages on PAN devices.
PAN action/command used to issue the displaying of text messages on PAN devices.
Reference to the superclass object.
If true, the requesting entity (e.g. retail electric provider) requires confirmation of the successful display of the text message.
Priority associated with the text message to be displayed.
Text to be displayed by a PAN device.
Transmission mode to be used for this PAN display control.
PAN action/command used to issue pricing information to a PAN device.
PAN action/command used to issue pricing information to a PAN device.
Reference to the superclass object.
Unique identifier for the commodity provider.
Detail for a single price command/action.
Detail for a single price command/action.
Reference to the superclass object.
Alternative measure of the cost of the energy consumed. An example might be the emissions of CO2 for each kWh of electricity consumed providing a measure of the environmental cost.
Cost unit for the alternate cost delivered field. One example is kg of CO2 per unit of measure.
Current time as determined by a PAN device.
Price of the commodity measured in base unit of currency per 'unitOfMeasure'.
Ratio of 'generationPrice' to the "normal" price chosen by the commodity provider.
Price of the commodity measured in base unit of currency per 'unitOfMeasure'.
Ratio of 'price' to the "normal" price chosen by the commodity provider.
Pricing tier as chosen by the commodity provider.
Maximum number of price tiers available.
Label for price tier.
Label of the current billing rate specified by commodity provider.
Register tier accumulating usage information.
Defines commodity as well as its base unit of measure.
PAN pricing command/action issuing this price detail.
Participation level of a given Pnode in a given AggregatePnode.
Participation level of a given Pnode in a given AggregatePnode.
Reference to the superclass object.
Used to calculate "participation" of Pnode in an AggregatePnode. For example, for regulation region this factor is 1 and total sum of all factors for a specific regulation region does not have to be 1. For pricing zone the total sum of all factors has to be 1.
Pass Through Bill is used for: 1)Two sided charge transactions with or without ISO involvement (hence the ?pass thru?) 2) Specific direct charges or payments that are calculated outside or provided directly to settlements 3) Specific charge bill determinants that are externally supplied and used in charge calculations
Pass Through Bill is used for: 1)Two sided charge transactions with or without ISO involvement (hence the ?pass thru?) 2) Specific direct charges or payments that are calculated outside or provided directly to settlements 3) Specific charge bill determinants that are externally supplied and used in charge calculations
Reference to the superclass object.
undocumented
The charge amount of the product/service.
Bill period end date
The settlement run type, for example: prelim, final, and rerun.
Bill period start date
The company to which the PTB transaction is billed.
The effective date of the transaction
Disputed transaction indicator
A flag indicating whether there is a profile data associated with the PTB.
The company to which the PTB transaction is paid.
The previous bill period end date
The previous bill period start date
The price of product/service.
The product identifier for determining the charge type of the transaction.
The company by which the PTB transaction service is provided.
The product quantity.
The end date of service provided, if periodic.
The start date of service provided, if periodic.
The company to which the PTB transaction is sold.
The tax on services taken.
The time zone code
The trade date
The date the transaction occurs.
The type of transaction. For example, charge customer, bill customer, matching AR/AP, or bill determinant
undocumented
undocumented
When present, a scalar conversion that needs to be applied to every IntervalReading.value contained in IntervalBlock.
When present, a scalar conversion that needs to be applied to every IntervalReading.value contained in IntervalBlock. This conversion results in a new associated ReadingType, reflecting the true dimensions of IntervalReading values after the conversion.
Reference to the superclass object.
Whether scalars should be applied before adding the 'offset'.
(if applicable) Offset to be added as well as multiplication using scalars.
(if scalar is rational number) When 'IntervalReading.value' is multiplied by 'scalarNumerator' and divided by this value, it causes a unit of measure conversion to occur, resulting in the 'ReadingType.unit'.
(if scalar is floating number) When multiplied with 'IntervalReading.value', it causes a unit of measure conversion to occur, according to the 'ReadingType.unit'.
(if scalar is integer or rational number) When the scalar is a simple integer, and this attribute is presented alone and multiplied with 'IntervalReading.value', it causes a unit of measure conversion to occur, resulting in the 'ReadingType.unit'. It is never used in conjunction with 'scalarFloat', only with 'scalarDenominator'.
Reading type resulting from this pending conversion.
Relationship between penstock head loss (in meters) and total discharge through the penstock (in cubic meters per second).
Relationship between penstock head loss (in meters) and total discharge through the penstock (in cubic meters per second). One or more turbines may be connected to the same penstock.
Reference to the superclass object.
A hydro generating unit has a penstock loss curve.
Common type for per-length impedance electrical catalogues.
Common type for per-length impedance electrical catalogues.
Reference to the superclass object.
Common type for per-length electrical catalogues describing line parameters.
Common type for per-length electrical catalogues describing line parameters.
Reference to the superclass object.
Wire spacing datasheet used to calculate this per-length parameter.
Impedance and admittance parameters per unit length for n-wire unbalanced lines, in matrix form.
Impedance and admittance parameters per unit length for n-wire unbalanced lines, in matrix form.
Reference to the superclass object.
Number of phase, neutral, and other wires retained. Constrains the number of matrix elements and the phase codes that can be used with this matrix.
Sequence impedance and admittance parameters per unit length, for transposed lines of 1, 2, or 3 phases.
Sequence impedance and admittance parameters per unit length, for transposed lines of 1, 2, or 3 phases. For 1-phase lines, define x=x0=xself. For 2-phase lines, define x=xs-xm and x0=xs+xm.
Reference to the superclass object.
Zero sequence shunt (charging) susceptance, per unit of length.
Positive sequence shunt (charging) susceptance, per unit of length.
Zero sequence shunt (charging) conductance, per unit of length.
Positive sequence shunt (charging) conductance, per unit of length.
Positive sequence series resistance, per unit of length.
Zero sequence series resistance, per unit of length.
Positive sequence series reactance, per unit of length.
Zero sequence series reactance, per unit of length.
An identification of a time interval that may have a given resolution.
An identification of a time interval that may have a given resolution.
Reference to the superclass object.
The number of units of time that compose an individual step within a period.
The start and end date and time for a given interval.
undocumented
General purpose information for name and other information to contact people.
General purpose information for name and other information to contact people.
Reference to the superclass object.
Electronic address.
Person's first name.
Landline phone number.
Person's last (family, sir) name.
Middle name(s) or initial(s).
Mobile phone number.
A prefix or title for the person's name, such as Miss, Mister, Doctor, etc.
Special service needs for the person (contact) are described; examples include life support, etc.
A suffix for the person's name, such as II, III, etc.
Roles played between Persons and Documents.
Roles played between Persons and Documents.
Reference to the superclass object.
undocumented
Role an organisation plays with respect to persons.
Role an organisation plays with respect to persons.
Reference to the superclass object.
Identifiers of the person held by an organisation, such as a government agency (federal, state, province, city, county), financial institutions, etc.
undocumented
The role of a person relative to a given piece of property.
The role of a person relative to a given piece of property. Examples of roles include: owner, renter, contractor, etc.
Reference to the superclass object.
undocumented
undocumented
A tunable impedance device normally used to offset line charging during single line faults in an ungrounded section of network.
A tunable impedance device normally used to offset line charging during single line faults in an ungrounded section of network.
Reference to the superclass object.
The mode of operation of the Petersen coil.
The nominal voltage for which the coil is designed.
The offset current that the Petersen coil controller is operating from the resonant point. This is normally a fixed amount for which the controller is configured and could be positive or negative. Typically 0 to 60 Amperes depending on voltage and resonance conditions.
The control current used to control the Petersen coil also known as the position current. Typically in the range of 20-200mA.
The maximum reactance.
The minimum reactance.
The nominal reactance. This is the operating point (normally over compensation) that is defined based on the resonance point in the healthy network condition. The impedance is calculated based on nominal voltage divided by position current.
Triplet of resistance, reactance, and susceptance matrix element values.
Triplet of resistance, reactance, and susceptance matrix element values.
Reference to the superclass object.
Susceptance matrix element value, per length of unit.
Resistance matrix element value, per length of unit.
Column-wise element index, assuming a symmetrical matrix. Ranges from 1 to N + N*(N-1)/2.
Reactance matrix element value, per length of unit.
Conductor phase impedance to which this data belongs.
A transformer phase shifting tap model that controls the phase angle difference across the power transformer and potentially the active power flow through the power transformer.
A transformer phase shifting tap model that controls the phase angle difference across the power transformer and potentially the active power flow through the power transformer. This phase tap model may also impact the voltage magnitude.
Reference to the superclass object.
Transformer end to which this phase tap changer belongs.
Describes the tap model for an asymmetrical phase shifting transformer in which the difference voltage vector adds to the primary side voltage.
Describes the tap model for an asymmetrical phase shifting transformer in which the difference voltage vector adds to the primary side voltage. The angle between the primary side voltage and the difference voltage is named the winding connection angle. The phase shift depends on both the difference voltage magnitude and the winding connection angle.
Reference to the superclass object.
The phase angle between the in-phase winding and the out-of -phase winding used for creating phase shift. The out-of-phase winding produces what is known as the difference voltage. Setting this angle to 90 degrees is not the same as a symmemtrical transformer.
Describes a tap changer with a linear relation between the tap step and the phase angle difference across the transformer.
Describes a tap changer with a linear relation between the tap step and the phase angle difference across the transformer. This is a mathematical model that is an approximation of a real phase tap changer.
Reference to the superclass object.
Phase shift per step position. A positive value indicates a positive phase shift from the winding where the tap is located to the other winding (for a two-winding transformer).
The reactance depend on the tap position according to a "u" shaped curve. The maximum reactance (xMax) appear at the low and high tap positions.
The reactance depend on the tap position according to a "u" shaped curve. The minimum reactance (xMin) appear at the mid tap position.
The non-linear phase tap changer describes the non-linear behavior of a phase tap changer.
The non-linear phase tap changer describes the non-linear behavior of a phase tap changer. This is a base class for the symmetrical and asymmetrical phase tap changer models. The details of these models can be found in the IEC 61970-301 document.
Reference to the superclass object.
The voltage step increment on the out of phase winding specified in percent of nominal voltage of the transformer end.
The reactance depend on the tap position according to a "u" shaped curve. The maximum reactance (xMax) appear at the low and high tap positions.
The reactance depend on the tap position according to a "u" shaped curve. The minimum reactance (xMin) appear at the mid tap position.
Describes a symmetrical phase shifting transformer tap model in which the secondary side voltage magnitude is the same as at the primary side.
Describes a symmetrical phase shifting transformer tap model in which the secondary side voltage magnitude is the same as at the primary side. The difference voltage magnitude is the base in an equal-sided triangle where the sides corresponds to the primary and secondary voltages. The phase angle difference corresponds to the top angle and can be expressed as twice the arctangent of half the total difference voltage.
Reference to the superclass object.
Describes a tabular curve for how the phase angle difference and impedance varies with the tap step.
Describes a tabular curve for how the phase angle difference and impedance varies with the tap step.
Reference to the superclass object.
Describes each tap step in the phase tap changer tabular curve.
Describes each tap step in the phase tap changer tabular curve.
Reference to the superclass object.
The angle difference in degrees.
The table of this point.
Value associated with branch group is used as compare.
Value associated with branch group is used as compare.
Reference to the superclass object.
The compare operation done on the branch group.
undocumented
Value associated with Equipment is used as compare.
Value associated with Equipment is used as compare.
Reference to the superclass object.
The compare operation done on the equipment.
undocumented
An output from one gate represent an input to another gate.
An output from one gate represent an input to another gate.
Reference to the superclass object.
undocumented
Gate input pin that is associated with a Measurement or a calculation of Measurement.
Gate input pin that is associated with a Measurement or a calculation of Measurement.
Reference to the superclass object.
undocumented
undocumented
Value associated with Terminal is used as compare.
Value associated with Terminal is used as compare.
Reference to the superclass object.
The compare operation done on the terminal.
undocumented
Represent a planned market.
Represent a planned market. For example an planned DA/HA/RT market.
Reference to the superclass object.
Market end time.
An identification that defines the attributes of the Market. In todays terms: Market Type: DA, RTM, Trade Date: 1/25/04, Trade Hour: 1-25.
Market start time.
Market type.
a market plan has a number of markets (DA, HA, RT)
This class represents planned events.
This class represents planned events. Used to model the various planned events in a market (closing time, clearing time, etc).
Reference to the superclass object.
Description of the planned event.
Planned event type.
Planned event identifier.
This is relative time so that this attribute can be used by more than one planned market. For example the bid submission is 10am everyday.
A Plant is a collection of equipment for purposes of generation.
A Plant is a collection of equipment for purposes of generation.
Reference to the superclass object.
A pricing node is directly associated with a connectivity node.
A pricing node is directly associated with a connectivity node. It is a pricing location for which market participants submit their bids, offers, buy/sell CRRs, and settle.
Reference to the superclass object.
End effective date of the period in which the price node definition is valid.
If true, this Pnode is public (prices are published for DA/RT and FTR markets), otherwise it is private (location is not usable by market for bidding/FTRs/transactions).
Start effective date of the period in which the price node definition is valid.
Pnode type
Price node usage: 'Control Area' 'Regulation Region' 'Price Zone' 'Spin Region' 'Non-Spin Region' 'Price Hub'
undocumented
undocumented
undocumented
undocumented
Pricing node clearing results posted for a given settlement period.
Pricing node clearing results posted for a given settlement period.
Reference to the superclass object.
This class allows SC to input different distribution factors for pricing node
This class allows SC to input different distribution factors for pricing node
Reference to the superclass object.
Used to calculate "participation" of Pnode in an AggregatePnode. For example, for regulation region this factor is 1 and total sum of all factors for a specific regulation region does not have to be 1. For pricing zone the total sum of all factors has to be 1.
Indication that this distribution factor is to apply during off peak.
Indication that this factor is to apply during Peak periods.
Point of delivery loss factor
undocumented
undocumented
Provides the total price, the cost component, the loss component, and the congestion component for Pnodes for the forward and real time markets.
Provides the total price, the cost component, the loss component, and the congestion component for Pnodes for the forward and real time markets. There are several prices produced based on the run type (MPM, RUC, Pricing, or Scheduling/Dispatch).
Reference to the superclass object.
Congestion component of Location Marginal Price (LMP) in monetary units per MW.
Cost component of Locational Marginal Pricing (LMP) in monetary units per MW.
Loss component of Location Marginal Price (LMP) in monetary units per MW.
Locational Marginal Price (LMP) ($/MWh)
total MW schedule at the pnode
undocumented
undocumented
undocumented
undocumented
undocumented
An identification of a set of values beeing adressed within a specific interval of time.
An identification of a set of values beeing adressed within a specific interval of time.
Reference to the superclass object.
A sequential value representing the relative position within a given time interval.
The quality of the information being provided. This quality may be estimated, not available, as provided, etc.
Principal quantity identified for a point.
Secondary quantity identified for a point.
undocumented
undocumented
undocumented
Logical point where transactions take place with operational interaction between cashier and the payment system; in certain cases the point of sale interacts directly with the end customer, in which case the cashier might not be a real person: for example a self-service kiosk or over the internet.
Logical point where transactions take place with operational interaction between cashier and the payment system; in certain cases the point of sale interacts directly with the end customer, in which case the cashier might not be a real person: for example a self-service kiosk or over the internet.
Reference to the superclass object.
Local description for where this point of sale is physically located.
Pole asset.
Pole asset.
Reference to the superclass object.
Kind of base for this pole.
True if a block of material has been attached to base of pole in ground for stability. This technique is used primarily when anchors can not be used.
Pole class: 1, 2, 3, 4, 5, 6, 7, H1, H2, Other, Unknown.
The framing structure mounted on the pole.
Diameter of the pole.
Joint pole agreement reference number.
Length of the pole (inclusive of any section of the pole that may be underground post-installation).
Kind of preservative for this pole.
Pole species. Aluminum, Aluminum Davit, Concrete, Fiberglass, Galvanized Davit, Galvanized, Steel Davit Primed, Steel Davit, Steel Standard Primed, Steel, Truncated, Wood-Treated, Wood-Hard, Wood-Salt Treated, Wood-Soft, Wood, Other, Unknown.
Date and time pole was last treated with preservative.
Kind of treatment for this pole.
Set of spatial coordinates that determine a point, defined in the coordinate system specified in 'Location.
Set of spatial coordinates that determine a point, defined in the coordinate system specified in 'Location. CoordinateSystem'. Use a single position point instance to desribe a point-oriented location. Use a sequence of position points to describe a line-oriented object (physical location of non-point oriented objects like cables or lines), or area of an object (like a substation or a geographical zone - in this case, have first and last position point with the same values).
Reference to the superclass object.
Zero-relative sequence number of this point within a series of points.
X axis position.
Y axis position.
(if applicable) Z axis position.
Location described by this position point.
A sensor used mainly in overhead distribution networks as the source of both current and voltage measurements.
A sensor used mainly in overhead distribution networks as the source of both current and voltage measurements.
Reference to the superclass object.
General purpose postal address information.
General purpose postal address information.
Reference to the superclass object.
Post office box.
Postal code for the address.
Street detail.
Town detail.
Instrument transformer (also known as Voltage Transformer) used to measure electrical qualities of the circuit that is being protected and/or monitored.
Instrument transformer (also known as Voltage Transformer) used to measure electrical qualities of the circuit that is being protected and/or monitored. Typically used as voltage transducer for the purpose of metering, protection, or sometimes auxiliary substation supply. A typical secondary voltage rating would be 120V.
Reference to the superclass object.
PT accuracy classification.
Nominal ratio between the primary and secondary voltage.
Potential transformer (PT) classification covering burden.
Potential transformer construction type.
Properties of potential transformer asset.
Properties of potential transformer asset.
Reference to the superclass object.
undocumented
undocumented
Ratio for the primary winding tap changer.
undocumented
Rated voltage on the primary side.
Ratio for the secondary winding tap changer.
Ratio for the tertiary winding tap changer.
An area or zone of the power system which is used for load shedding purposes.
An area or zone of the power system which is used for load shedding purposes.
Reference to the superclass object.
First level (amount) of load to cut as a percentage of total zone load.
Second level (amount) of load to cut as a percentage of total zone load.
Pricing can be based on power quality.
Pricing can be based on power quality.
Reference to the superclass object.
Emergency high voltage limit.
Emergency low voltage limit.
Normal high voltage limit.
Normal low voltage limit.
Threshold minimum power factor for this PricingStructure, specified in instances where a special charge is levied if the actual power factor for a Service falls below the value specified here.
Value of uninterrupted service (Cost per energy).
Value of uninterrupted service (Cost per active power).
Voltage imbalance violation cost (Cost per unit Voltage).
Voltage limit violation cost (Cost per unit Voltage).
A (document/collection) that describe a set of changes to the network.
A (document/collection) that describe a set of changes to the network.
Reference to the superclass object.
undocumented
undocumented
undocumented
Priority between competing projects. Use 0 for don t care. Use 1 for highest priority. Use 2 as priority is less than 1 and so on.
Describes the state the project realisation are from starting planning until it is commissioned if not cancelled.
Type of project.
Version of the project. Changes to a project is not modeled. So the project with the highest version are the valid/latest project. Only positive numbers equal or higher than 1 are allowed.
undocumented
A power system resource can be an item of equipment such as a switch, an equipment container containing many individual items of equipment such as a substation, or an organisational entity such as sub-control area.
A power system resource can be an item of equipment such as a switch, an equipment container containing many individual items of equipment such as a substation, or an organisational entity such as sub-control area. Power system resources can have measurements associated.
Reference to the superclass object.
Datasheet information for this power system resource.
Location of this power system resource.
Custom classification for this power system resource.
Power system stabilizer function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Power system stabilizer function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Excitation system model with which this power system stabilizer model is associated.
<font color="#0f0f0f">Power system stabilizer</font> function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
<font color="#0f0f0f">Power system stabilizer</font> function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
A collection of dependent projects.
A collection of dependent projects.
Reference to the superclass object.
undocumented
An electrical device consisting of two or more coupled windings, with or without a magnetic core, for introducing mutual coupling between electric circuits.
An electrical device consisting of two or more coupled windings, with or without a magnetic core, for introducing mutual coupling between electric circuits. Transformers can be used to control voltage and phase shift (active power flow).
Reference to the superclass object.
The highest operating current (Ib in the IEC 60909-0) before short circuit (depends on network configuration and relevant reliability philosophy). It is used for calculation of the impedance correction factor KT defined in IEC 60909-0.
The highest operating voltage (Ub in the IEC 60909-0) before short circuit. It is used for calculation of the impedance correction factor KT defined in IEC 60909-0. This is worst case voltage on the low side winding (Section 3.7.1 in the standard). Used to define operating conditions.
The angle of power factor before short circuit (phib in the IEC 60909-0). It is used for calculation of the impedance correction factor KT defined in IEC 60909-0. This is the worst case power factor. Used to define operating conditions.
The minimum operating voltage (uQmin in the IEC 60909-0) at the high voltage side (Q side) of the unit transformer of the power station unit. A value well established from long-term operating experience of the system. It is used for calculation of the impedance correction factor KG defined in IEC 60909-0
Indicates whether the machine is part of a power station unit. Used for short circuit data exchange according to IEC 60909
It is used to define if the data (other attributes related to short circuit data exchange) defines long term operational conditions or not. Used for short circuit data exchange according to IEC 60909.
Vector group of the transformer for protective relaying, e.g., Dyn1. For unbalanced transformers, this may not be simply determined from the constituent winding connections and phase angle dispacements.
A PowerTransformerEnd is associated with each Terminal of a PowerTransformer.
A PowerTransformerEnd is associated with each Terminal of a PowerTransformer. The impedance values r, r0, x, and x0 of a PowerTransformerEnd represents a star equivalent as follows
Reference to the superclass object.
Magnetizing branch susceptance (B mag). The value can be positive or negative.
Zero sequence magnetizing branch susceptance.
Kind of connection.
Magnetizing branch conductance.
Zero sequence magnetizing branch conductance (star-model).
Terminal voltage phase angle displacement where 360 degrees are represented with clock hours. The valid values are 0 to 11. For example, for the secondary side end of a transformer with vector group code of 'Dyn11', specify the connection kind as wye with neutral and specify the phase angle of the clock as 11. The clock value of the transformer end number specified as 1, is assumed to be zero. Note the transformer end number is not assumed to be the same as the terminal sequence number.
Resistance (star-model) of the transformer end. The attribute shall be equal or greater than zero for non-equivalent transformers.
Zero sequence series resistance (star-model) of the transformer end.
Normal apparent power rating. The attribute shall be a positive value. For a two-winding transformer the values for the high and low voltage sides shall be identical.
Rated voltage: phase-phase for three-phase windings, and either phase-phase or phase-neutral for single-phase windings. A high voltage side, as given by TransformerEnd.endNumber, shall have a ratedU that is greater or equal than ratedU for the lower voltage sides.
Positive sequence series reactance (star-model) of the transformer end.
Zero sequence series reactance of the transformer end.
The power transformer of this power transformer end.
Set of power transformer data, from an equipment library.
Set of power transformer data, from an equipment library.
Reference to the superclass object.
The cost corresponding to a specific measure and expressed in a currency.
The cost corresponding to a specific measure and expressed in a currency.
Reference to the superclass object.
A number of monetary units specified in a unit of currency.
The category of a price to be used in a price calculation. The price category is mutually agreed between System Operators.
The direction indicates whether a System Operator pays the Market Parties or inverse.
undocumented
Grouping of pricing components and prices used in the creation of customer charges and the eligibility criteria under which these terms may be offered to a customer.
Grouping of pricing components and prices used in the creation of customer charges and the eligibility criteria under which these terms may be offered to a customer. The reasons for grouping include state, customer classification, site characteristics, classification (i.e. fee price structure, deposit price structure, electric service price structure, etc.) and accounting requirements.
Reference to the superclass object.
Unique user-allocated key for this pricing structure, used by company representatives to identify the correct price structure for allocating to a customer. For rate schedules it is often prefixed by a state code.
Absolute maximum valid non-demand usage quantity used in validating a customer's billed non-demand usage.
Used in place of actual computed estimated average when history of usage is not available, and typically manually entered by customer accounting.
Absolute minimum valid non-demand usage quantity used in validating a customer's billed non-demand usage.
(accounting) Kind of revenue, often used to determine the grace period allowed, before collection actions are taken on a customer (grace periods vary between revenue classes).
True if this pricing structure is not taxable.
Service category to which this pricing structure applies.
All tariffs used by this pricing structure.
All service delivery points (with prepayment meter running as a stand-alone device, with no CustomerAgreement or Customer) to which this pricing structure applies.
The machine used to develop mechanical energy used to drive a generator.
The machine used to develop mechanical energy used to drive a generator.
Reference to the superclass object.
Rating of prime mover.
Synchronous machines this Prime mover drives.
Priority definition.
Priority definition.
Reference to the superclass object.
Justification for 'rank'.
Priority level; usually, lower number means high priority, but the details are provided in 'type'.
Type describing 'rank'; e.g., high, emergency, etc.
Documented procedure for various types of work or work tasks on assets.
Documented procedure for various types of work or work tasks on assets.
Reference to the superclass object.
Textual description of this procedure.
Kind of procedure.
Sequence number in a sequence of procedures being performed.
All assets to which this procedure applies.
undocumented
Document containing this measurement.
A data set recorded each time a procedure is executed.
A data set recorded each time a procedure is executed. Observed results are captured in associated measurement values and/or values for properties relevant to the type of procedure performed.
Reference to the superclass object.
Date and time procedure was completed.
undocumented
Procedure capturing this data set.
undocumented
The formal specification of a set of business transactions having the same business goal.
The formal specification of a set of business transactions having the same business goal.
Reference to the superclass object.
The classification mechanism used to group a set of objects together within a business process. The grouping may be of a detailed or a summary nature.
The kind of business process.
undocumented
Asset model by a specific manufacturer.
Asset model by a specific manufacturer.
Reference to the superclass object.
Kind of corporate standard for this asset model.
Manufacturer's model number.
Version number for product model, which indicates vintage of the product.
Intended usage for this asset model.
Total manufactured weight of asset.
Generic asset model or material satisified by this product asset model.
Manufacturer of this asset model.
Component of a bid that pertains to one market product.
Component of a bid that pertains to one market product.
Reference to the superclass object.
A bid comprises one or more product bids of market products
undocumented
A profile is a simpler curve type.
A profile is a simpler curve type.
Reference to the superclass object.
Data for profile.
Data for profile.
Reference to the superclass object.
Bid price associated with contract
Capacity level for the profile, in MW.
Energy level for the profile, in MWH.
Minimum MW value of contract
Sequence to provide item numbering for the profile. { greater than or equal to 1 }
Start date/time for this profile.
Stop date/time for this profile.
A profile has profile data associated with it.
A collection of related work.
A collection of related work. For construction projects and maintenance projects, multiple phases may be performed.
Reference to the superclass object.
Overall project budget.
undocumented
undocumented
undocumented
The ProjectSteps are ordered by the actualStart and actualEnds so that a dependent ProjectStep will have a actualStart after an actualEnd.
The ProjectSteps are ordered by the actualStart and actualEnds so that a dependent ProjectStep will have a actualStart after an actualEnd.
Reference to the superclass object.
Actual date and time for when the project is commissioned and committed to the network model.
Actual date and time for when the project is commissioned and committed to the network model.
Estimated date and time for when the project will be commissioned and committed to the network model.
Estimated date and time for when the project will be commissioned and committed to the network model.
undocumented
undocumented
Role an organisation plays with respect to property (for example, the organisation may be the owner, renter, occupier, taxiing authority, etc.).
Role an organisation plays with respect to property (for example, the organisation may be the owner, renter, occupier, taxiing authority, etc.).
Reference to the superclass object.
Unit of property for reporting purposes.
Unit of property for reporting purposes.
Reference to the superclass object.
A code that identifies appropriate type of property accounts such as distribution, streetlgihts, communications.
Activity code identifies a specific and distinguishable work action.
Used for property record accounting. For example, in the USA, this would be a FERC account.
undocumented
undocumented
Supports definition of one or more parameters of several different datatypes for use by proprietary user-defined models.
Supports definition of one or more parameters of several different datatypes for use by proprietary user-defined models. NOTE: This class does not inherit from IdentifiedObject since it is not intended that a single instance of it be referenced by more than one proprietary user-defined model instance.
Reference to the superclass object.
Used for boolean parameter value. If this attribute is populated, integerParameterValue and floatParameterValue will not be.
Used for floating point parameter value. If this attribute is populated, booleanParameterValue and integerParameterValue will not be.
Used for integer parameter value. If this attribute is populated, booleanParameterValue and floatParameterValue will not be.
Sequence number of the parameter among the set of parameters associated with the related proprietary user-defined model.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
Proprietary user-defined model with which this parameter is associated.
A ProtectedSwitch is a switching device that can be operated by ProtectionEquipment.
A ProtectedSwitch is a switching device that can be operated by ProtectionEquipment.
Reference to the superclass object.
The maximum fault current a breaking device can break safely under prescribed conditions of use.
An electrical device designed to respond to input conditions in a prescribed manner and after specified conditions are met to cause contact operation or similar abrupt change in associated electric control circuits, or simply to display the detected condition.
An electrical device designed to respond to input conditions in a prescribed manner and after specified conditions are met to cause contact operation or similar abrupt change in associated electric control circuits, or simply to display the detected condition. Protection equipment are associated with conducting equipment and usually operate circuit breakers.
Reference to the superclass object.
The maximum allowable value.
The minimum allowable value.
Direction same as positive active power flow value.
The time delay from detection of abnormal conditions to relay operation.
The unit multiplier of the value.
The unit of measure of the value.
Protection equipment may be used to protect specific conducting equipment.
Protected switches operated by this ProtectionEquipment.
Properties of protection equipment asset.
Properties of protection equipment asset.
Reference to the superclass object.
Actual ground trip for this type of relay, if applicable.
Actual phase trip for this type of relay, if applicable.
A protective action for supporting the integrity of the power system.
A protective action for supporting the integrity of the power system.
Reference to the superclass object.
The status of the class set by operation or by signal. Optional field that will override other status fields.
The default/normal value used when other active signal/values are missing.
undocumented
undocumented
undocumented
undocumented
Protective actions on non-switching equipment.
Protective actions on non-switching equipment. The operating condition is adjusted.
Reference to the superclass object.
The adjustment is given in percent of the active value.
The adjustment is given in value of the active value.
Defines the kind of adjustment that should be done. With this value the correct attribute containing the value needs to be used.
If true, the adjusted value is an reduction. Other wise it is an increase in the value.
The adjustment is given by a new active value.
undocumented
undocumented
undocumented
A collection of protective actions to protect the integrity of the power system.
A collection of protective actions to protect the integrity of the power system.
Reference to the superclass object.
Protective action to put an Equipment in-service/out-of-service.
Protective action to put an Equipment in-service/out-of-service.
Reference to the superclass object.
If true the equipment is put in-service, otherwise out-of-service.
undocumented
Protective action to change regulation to Equipment.
Protective action to change regulation to Equipment.
Reference to the superclass object.
If true the regulator is put in-service, otherwise out-of-service (no regulation).
The target value specified the new case input for the regulator. The value has the units appropriate to the mode attribute. The protective action does not change the mode attribute.
undocumented
Italian PSS - three input PSS (speed, frequency, power).
Italian PSS - three input PSS (speed, frequency, power).
Reference to the superclass object.
Frequency power input gain (KF). Typical Value = 5.
Electric power input gain (KPE). Typical Value = 0.3.
PSS gain (KS). Typical Value = 1.
Shaft speed power input gain (KW). Typical Value = 0.
Minimum power PSS enabling (PMIN). Typical Value = 0.25.
Lead/lag time constant (T10). Typical Value = 0.
Washout (T5). Typical Value = 3.5.
Filter time constant (T6). Typical Value = 0.
Lead/lag time constant (T7). Typical Value = 0.
Lead/lag time constant (T8). Typical Value = 0.
Lead/lag time constant (T9). Typical Value = 0.
Electric power filter time constant (TPE). Typical Value = 0.05.
<font color="#0f0f0f">Signal selector (VadAt).</font> <font color="#0f0f0f">true = closed (Generator Power is greater than Pmin)</font> <font color="#0f0f0f">false = open (Pe is smaller than Pmin).</font> <font color="#0f0f0f">Typical Value = true.</font>
Stabilizer output max limit (VSMN). Typical Value = -0.06.
Stabilizer output min limit (VSMX). Typical Value = 0.06.
Single input power system stabilizer.
Single input power system stabilizer. It is a modified version in order to allow representation of various vendors' implementations on PSS type 1A.
Reference to the superclass object.
Notch filter parameter (A1).
Notch filter parameter (A2).
Notch filter parameter (A3).
Notch filter parameter (A4).
Notch filter parameter (A5).
Notch filter parameter (A6).
Notch filter parameter (A7).
Notch filter parameter (A8).
Type of input signal.
Selector (Kd). true = e-sTdelay used false = e-sTdelay not used.
Stabilizer gain (Ks).
Lead/lag time constant (T1).
Lead/lag time constant (T2).
Lead/lag time constant (T3).
Lead/lag time constant (T4).
Washout time constant (T5).
Transducer time constant (T6).
Time constant (Tdelay).
Stabilizer input cutoff threshold (Vcl).
Stabilizer input cutoff threshold (Vcu).
Maximum stabilizer output (Vrmax).
Minimum stabilizer output (Vrmin).
Modified IEEE PSS2B Model.
Modified IEEE PSS2B Model. Extra lead/lag (or rate) block added at end (up to 4 lead/lags total).
Reference to the superclass object.
Numerator constant (a). Typical Value = 1.
Type of input signal #1. Typical Value = rotorSpeed.
Type of input signal #2. Typical Value = generatorElectricalPower.
Stabilizer gain (Ks1). Typical Value = 12.
Gain on signal #2 (Ks2). Typical Value = 0.2.
Gain on signal #2 input before ramp-tracking filter (Ks3). Typical Value = 1.
Gain on signal #2 input after ramp-tracking filter (Ks4). Typical Value = 1.
Denominator order of ramp tracking filter (M). Typical Value = 5.
Order of ramp tracking filter (N). Typical Value = 1.
Lead/lag time constant (T1). Typical Value = 0.12.
Lead/lag time constant (T10). Typical Value = 0.
Lead/lag time constant (T11). Typical Value = 0.
Lead/lag time constant (T2). Typical Value = 0.02.
Lead/lag time constant (T3). Typical Value = 0.3.
Lead/lag time constant (T4). Typical Value = 0.02.
Time constant on signal #1 (T6). Typical Value = 0.
Time constant on signal #2 (T7). Typical Value = 2.
Lead of ramp tracking filter (T8). Typical Value = 0.2.
Lag of ramp tracking filter (T9). Typical Value = 0.1.
Lead constant (Ta). Typical Value = 0.
Lag time constant (Tb). Typical Value = 0.
First washout on signal #1 (Tw1). Typical Value = 2.
Second washout on signal #1 (Tw2). Typical Value = 2.
First washout on signal #2 (Tw3). Typical Value = 2.
Second washout on signal #2 (Tw4). Typical Value = 0.
Input signal #1 max limit (Vsi1max). Typical Value = 2.
Input signal #1 min limit (Vsi1min). Typical Value = -2.
Input signal #2 max limit (Vsi2max). Typical Value = 2.
Input signal #2 min limit (Vsi2min). Typical Value = -2.
Stabilizer output max limit (Vstmax). Typical Value = 0.1.
Stabilizer output min limit (Vstmin). Typical Value = -0.1.
PTI Microprocessor-Based Stabilizer type 1.
PTI Microprocessor-Based Stabilizer type 1.
Reference to the superclass object.
Type of input signal #1. Typical Value = rotorAngularFrequencyDeviation.
Type of input signal #2. Typical Value = generatorElectricalPower.
Gain (K1).
Gain (K2).
Limiter (Lsmax).
Limiter (Lsmin).
Time constant (T1).
Time constant (T10).
Time constant (T2).
Time constant (T3).
Time constant (T4).
Time constant (T5).
Time constant (T6).
Time constant (T7).
Time constant (T8).
Time constant (T9).
Cutoff limiter (Vcl).
Cutoff limiter (Vcu).
Italian PSS - Detailed PSS.
Italian PSS - Detailed PSS.
Reference to the superclass object.
Selector for Second washout enabling (CTW2). true = second washout filter is bypassed false = second washout filter in use. Typical Value = true.
Stabilizer output dead band (DeadBand). Typical Value = 0.
Selector for Frequency/shaft speed input (IsFreq). true = speed false = frequency. Typical Value = true.
Frequency/shaft speed input gain (KF). Typical Value = 5.
Electric power input gain (KPE). Typical Value = 0.3.
PSS gain (KPSS). Typical Value = 1.
Minimum power PSS enabling (Pmn). Typical Value = 0.25.
Lead/lag time constant (TL1). Typical Value = 0.
Lead/lag time constant (TL2). Typical Value = 0.
Lead/lag time constant (TL3). Typical Value = 0.
Lead/lag time constant (TL4). Typical Value = 0.
Electric power filter time constant (TPE). Typical Value = 0.05.
First WashOut (Tw1). Typical Value = 3.5.
Second WashOut (Tw2). Typical Value = 0.
<font color="#0f0f0f">Signal selector (VadAtt).</font> <font color="#0f0f0f">true = closed (Generator Power is greater than Pmin)</font> <font color="#0f0f0f">false = open (Pe is smaller than Pmin).</font> <font color="#0f0f0f">Typical Value = true.</font>
Stabilizer output max limit (VSMN). Typical Value = -0.1.
Stabilizer output min limit (VSMX). Typical Value = 0.1.
Power system stabilizer typically associated with ExcELIN2 (though PssIEEE2B or Pss2B can also be used).
Power system stabilizer typically associated with ExcELIN2 (though PssIEEE2B or Pss2B can also be used).
Reference to the superclass object.
Coefficient (a_PSS). Typical Value = 0.1.
Gain (Ks1). Typical Value = 1.
Gain (Ks2). Typical Value = 0.1.
Coefficient (p_PSS) (>=0 and <=4). Typical Value = 0.1.
PSS limiter (psslim). Typical Value = 0.1.
Time constant (Ts1). Typical Value = 0.
Time constant (Ts2). Typical Value = 1.
Time constant (Ts3). Typical Value = 1.
Time constant (Ts4). Typical Value = 0.1.
Time constant (Ts5). Typical Value = 0.
Time constant (Ts6). Typical Value = 1.
The class represents IEEE Std 421.5-2005 type PSS1A power system stabilizer model.
The class represents IEEE Std 421.5-2005 type PSS1A power system stabilizer model. PSS1A is the generalized form of a PSS with a single input. Some common stabilizer input signals are speed, frequency, and power.
Reference to the superclass object.
PSS signal conditioning frequency filter constant (A1). Typical Value = 0.061.
PSS signal conditioning frequency filter constant (A2). Typical Value = 0.0017.
Type of input signal. Typical Value = rotorAngularFrequencyDeviation.
Stabilizer gain (Ks). Typical Value = 5.
Lead/lag time constant (T1). Typical Value = 0.3.
Lead/lag time constant (T2). Typical Value = 0.03.
Lead/lag time constant (T3). Typical Value = 0.3.
Lead/lag time constant (T4). Typical Value = 0.03.
Washout time constant (T5). Typical Value = 10.
Transducer time constant (T6). Typical Value = 0.01.
Maximum stabilizer output (Vrmax). Typical Value = 0.05.
Minimum stabilizer output (Vrmin). Typical Value = -0.05.
The class represents IEEE Std 421.5-2005 type PSS2B power system stabilizer model.
The class represents IEEE Std 421.5-2005 type PSS2B power system stabilizer model. This stabilizer model is designed to represent a variety of dual-input stabilizers, which normally use combinations of power and speed or frequency to derive the stabilizing signal.
Reference to the superclass object.
Type of input signal #1. Typical Value = rotorSpeed.
Type of input signal #2. Typical Value = generatorElectricalPower.
Stabilizer gain (Ks1). Typical Value = 12.
Gain on signal #2 (Ks2). Typical Value = 0.2.
Gain on signal #2 input before ramp-tracking filter (Ks3). Typical Value = 1.
Denominator order of ramp tracking filter (M). Typical Value = 5.
Order of ramp tracking filter (N). Typical Value = 1.
Lead/lag time constant (T1). Typical Value = 0.12.
Lead/lag time constant (T10). Typical Value = 0.
Lead/lag time constant (T11). Typical Value = 0.
Lead/lag time constant (T2). Typical Value = 0.02.
Lead/lag time constant (T3). Typical Value = 0.3.
Lead/lag time constant (T4). Typical Value = 0.02.
Time constant on signal #1 (T6). Typical Value = 0.
Time constant on signal #2 (T7). Typical Value = 2.
Lead of ramp tracking filter (T8). Typical Value = 0.2.
Lag of ramp tracking filter (T9). Typical Value = 0.1.
First washout on signal #1 (Tw1). Typical Value = 2.
Second washout on signal #1 (Tw2). Typical Value = 2.
First washout on signal #2 (Tw3). Typical Value = 2.
Second washout on signal #2 (Tw4). Typical Value = 0.
Input signal #1 max limit (Vsi1max). Typical Value = 2.
Input signal #1 min limit (Vsi1min). Typical Value = -2.
Input signal #2 max limit (Vsi2max). Typical Value = 2.
Input signal #2 min limit (Vsi2min). Typical Value = -2.
Stabilizer output max limit (Vstmax). Typical Value = 0.1.
Stabilizer output min limit (Vstmin). Typical Value = -0.1.
The class represents IEEE Std 421.5-2005 type PSS3B power system stabilizer model.
The class represents IEEE Std 421.5-2005 type PSS3B power system stabilizer model. The PSS model PSS3B has dual inputs of electrical power and rotor angular frequency deviation. The signals are used to derive an equivalent mechanical power signal.
Reference to the superclass object.
Notch filter parameter (A1). Typical Value = 0.359.
Notch filter parameter (A2). Typical Value = 0.586.
Notch filter parameter (A3). Typical Value = 0.429.
Notch filter parameter (A4). Typical Value = 0.564.
Notch filter parameter (A5). Typical Value = 0.001.
Notch filter parameter (A6). Typical Value = 0.
Notch filter parameter (A7). Typical Value = 0.031.
Notch filter parameter (A8). Typical Value = 0.
Type of input signal #1. Typical Value = generatorElectricalPower.
Type of input signal #2. Typical Value = rotorSpeed.
Gain on signal # 1 (Ks1). Typical Value = -0.602.
Gain on signal # 2 (Ks2). Typical Value = 30.12.
Transducer time constant (T1). Typical Value = 0.012.
Transducer time constant (T2). Typical Value = 0.012.
Washout time constant (Tw1). Typical Value = 0.3.
Washout time constant (Tw2). Typical Value = 0.3.
Washout time constant (Tw3). Typical Value = 0.6.
Stabilizer output max limit (Vstmax). Typical Value = 0.1.
Stabilizer output min limit (Vstmin). Typical Value = -0.1.
The class represents IEEE Std 421.5-2005 type PSS2B power system stabilizer model.
The class represents IEEE Std 421.5-2005 type PSS2B power system stabilizer model. The PSS4B model represents a structure based on multiple working frequency bands. Three separate bands, respectively dedicated to the low-, intermediate- and high-frequency modes of oscillations, are used in this delta-omega (speed input) PSS.
Reference to the superclass object.
Notch filter 1 (high-frequency band): Three dB bandwidth (Bwi).
Notch filter 2 (high-frequency band): Three dB bandwidth (Bwi).
Notch filter 1 (low-frequency band): Three dB bandwidth (Bwi).
Notch filter 2 (low-frequency band): Three dB bandwidth (Bwi).
High band gain (KH). Typical Value = 120.
High band differential filter gain (KH1). Typical Value = 66.
High band first lead-lag blocks coefficient (KH11). Typical Value = 1.
High band first lead-lag blocks coefficient (KH17). Typical Value = 1.
High band differential filter gain (KH2). Typical Value = 66.
Intermediate band gain (KI). Typical Value = 30.
Intermediate band differential filter gain (KI1). Typical Value = 66.
Intermediate band first lead-lag blocks coefficient (KI11). Typical Value = 1.
Intermediate band first lead-lag blocks coefficient (KI17). Typical Value = 1.
Intermediate band differential filter gain (KI2). Typical Value = 66.
Low band gain (KL). Typical Value = 7.5.
Low band differential filter gain (KL1). Typical Value = 66.
Low band first lead-lag blocks coefficient (KL11). Typical Value = 1.
Low band first lead-lag blocks coefficient (KL17). Typical Value = 1.
Low band differential filter gain (KL2). Typical Value = 66.
Notch filter 1 (high-frequency band): filter frequency (omegani).
Notch filter 2 (high-frequency band): filter frequency (omegani).
Notch filter 1 (low-frequency band): filter frequency (omegani).
Notch filter 2 (low-frequency band): filter frequency (omegani).
High band time constant (TH1). Typical Value = 0.01513.
High band time constant (TH10). Typical Value = 0.
High band time constant (TH11). Typical Value = 0.
High band time constant (TH12). Typical Value = 0.
High band time constant (TH2). Typical Value = 0.01816.
High band time constant (TH3). Typical Value = 0.
High band time constant (TH4). Typical Value = 0.
High band time constant (TH5). Typical Value = 0.
High band time constant (TH6). Typical Value = 0.
High band time constant (TH7). Typical Value = 0.01816.
High band time constant (TH8). Typical Value = 0.02179.
High band time constant (TH9). Typical Value = 0.
Intermediate band time constant (TI1). Typical Value = 0.173.
Intermediate band time constant (TI11). Typical Value = 0.
Intermediate band time constant (TI11). Typical Value = 0.
Intermediate band time constant (TI2). Typical Value = 0.
Intermediate band time constant (TI2). Typical Value = 0.2075.
Intermediate band time constant (TI3). Typical Value = 0.
Intermediate band time constant (TI4). Typical Value = 0.
Intermediate band time constant (TI5). Typical Value = 0.
Intermediate band time constant (TI6). Typical Value = 0.
Intermediate band time constant (TI7). Typical Value = 0.2075.
Intermediate band time constant (TI8). Typical Value = 0.2491.
Intermediate band time constant (TI9). Typical Value = 0.
Low band time constant (TL1). Typical Value = 1.73.
Low band time constant (TL10). Typical Value = 0.
Low band time constant (TL11). Typical Value = 0.
Low band time constant (TL12). Typical Value = 0.
Low band time constant (TL2). Typical Value = 2.075.
Low band time constant (TL3). Typical Value = 0.
Low band time constant (TL4). Typical Value = 0.
Low band time constant (TL5). Typical Value = 0.
Low band time constant (TL6). Typical Value = 0.
Low band time constant (TL7). Typical Value = 2.075.
Low band time constant (TL8). Typical Value = 2.491.
Low band time constant (TL9). Typical Value = 0.
High band output maximum limit (VHmax). Typical Value = 0.6.
High band output minimum limit (VHmin). Typical Value = -0.6.
Intermediate band output maximum limit (VImax). Typical Value = 0.6.
Intermediate band output minimum limit (VImin). Typical Value = -0.6.
Low band output maximum limit (VLmax). Typical Value = 0.075.
Low band output minimum limit (VLmin). Typical Value = -0.075.
PSS output maximum limit (VSTmax). Typical Value = 0.15.
PSS output minimum limit (VSTmin). Typical Value = -0.15.
PTI Microprocessor-Based Stabilizer type 1.
PTI Microprocessor-Based Stabilizer type 1.
Reference to the superclass object.
Time step related to activation of controls (Dtc). Typical Value = 0.025.
Time step frequency calculation (Dtf). Typical Value = 0.025.
Time step active power calculation (Dtp). Typical Value = 0.0125.
Gain (K). Typical Value = 9.
(M). M=2*H. Typical Value = 5.
Time constant (T1). Typical Value = 0.3.
Time constant (T2). Typical Value = 1.
Time constant (T3). Typical Value = 0.2.
Time constant (T4). Typical Value = 0.05.
Time constant (Tf). Typical Value = 0.2.
Time constant (Tp). Typical Value = 0.2.
PTI Microprocessor-Based Stabilizer type 3.
PTI Microprocessor-Based Stabilizer type 3.
Reference to the superclass object.
Filter coefficient (A0).
Limiter (Al).
Filter coefficient (A2).
Filter coefficient (A3).
Filter coefficient (A4).
Filter coefficient (A5).
Limiter (Al).
Threshold value above which output averaging will be bypassed (Athres). Typical Value = 0.005.
Filter coefficient (B0).
Filter coefficient (B1).
Filter coefficient (B2).
Filter coefficient (B3).
Filter coefficient (B4).
Filter coefficient (B5).
Limiter (Dl).
Time step related to activation of controls (0.03 for 50 Hz) (Dtc). Typical Value = 0.025.
Time step frequency calculation (0.03 for 50 Hz) (Dtf). Typical Value = 0.025.
Time step active power calculation (0.015 for 50 Hz) (Dtp). Typical Value = 0.0125.
Digital/analog output switch (Isw). true = produce analog output false = convert to digital output, using tap selection table.
Gain (K). Typical Value = 9.
Threshold value (Lthres).
(M). M=2*H. Typical Value = 5.
Number of control outputs to average (Nav) (1 <= Nav <= 16). Typical Value = 4.
Number of counts at limit to active limit function (Ncl) (>0).
Number of counts until reset after limit function is triggered (Ncr).
(Pmin).
Time constant (T1). Typical Value = 0.3.
Time constant (T2). Typical Value = 1.
Time constant (T3). Typical Value = 0.2.
Time constant (T4). Typical Value = 0.05.
Time constant (T5).
Time constant (T6).
Time constant (Tf). Typical Value = 0.2.
Time constant (Tp). Typical Value = 0.2.
Power sensitive stabilizer model.
Power sensitive stabilizer model.
Reference to the superclass object.
Gain (Kx).
Time constant (Ta).
Time constant (Tb).
Time constant (Tc).
Time constant (Td).
Time constant (Te).
Time constant (Tt).
Reset time constant (Tx1).
Time constant (Tx2).
Limiter (Vsmax).
Limiter (Vsmin).
Model for Siemens �H infinity� power system stabilizer with generator electrical power input.
Model for Siemens �H infinity� power system stabilizer with generator electrical power input.
Reference to the superclass object.
Main gain (K). Typical Value = 1.
Gain 0 (K0). Typical Value = 0.012.
Gain 1 (K1). Typical Value = 0.488.
Gain 2 (K2). Typical Value = 0.064.
Gain 3 (K3). Typical Value = 0.224.
Gain 4 (K4). Typical Value = 0.1.
Time constant 1 (T1). Typical Value = 0.076.
Time constant 2 (T2). Typical Value = 0.086.
Time constant 3 (T3). Typical Value = 1.068.
Time constant 4 (T4). Typical Value = 1.913.
Input time constant (Td). Typical Value = 10.
Output maximum limit (Vsmax). Typical Value = 0.1.
Output minimum limit (Vsmin). Typical Value = -0.1.
PSS Slovakian type � three inputs.
PSS Slovakian type � three inputs.
Reference to the superclass object.
Gain P (K1). Typical Value = -0.3.
Gain fe (K2). Typical Value = -0.15.
Gain If (K3). Typical Value = 10.
Denominator time constant (T1). Typical Value = 0.3.
Filter time constant (T2). Typical Value = 0.35.
Denominator time constant (T3). Typical Value = 0.22.
Filter time constant (T4). Typical Value = 0.02.
Denominator time constant (T5). Typical Value = 0.02.
Filter time constant (T6). Typical Value = 0.02.
Stabilizer output max limit (Vsmax). Typical Value = 0.4.
Stabilizer output min limit (Vsmin). Typical Value = -0.4.
Dual input Power System Stabilizer, based on IEEE type 2, with modified output limiter defined by WECC (Western Electricity Coordinating Council, USA).
Dual input Power System Stabilizer, based on IEEE type 2, with modified output limiter defined by WECC (Western Electricity Coordinating Council, USA).
Reference to the superclass object.
Type of input signal #1.
Type of input signal #2.
Input signal 1 gain (K1).
Input signal 2 gain (K2).
Input signal 1 transducer time constant (T1).
Lag time constant (T10).
Input signal 2 transducer time constant (T2).
Stabilizer washout time constant (T3).
Stabilizer washout time lag constant (T4) (>0).
Lead time constant (T5).
Lag time constant (T6).
Lead time constant (T7).
Lag time constant (T8).
Lead time constant (T9).
Minimum value for voltage compensator output (VCL).
Maximum value for voltage compensator output (VCU).
Maximum output signal (Vsmax).
Minimum output signal (Vsmin).
The operating cost of a Pump Storage Hydro Unit operating as a hydro pump.
The operating cost of a Pump Storage Hydro Unit operating as a hydro pump. This schedule is assocated with the hourly parameters in a resource bid associated with a specific product within the bid.
Reference to the superclass object.
undocumented
The fixed operating level of a Pump Storage Hydro Unit operating as a hydro pump.
The fixed operating level of a Pump Storage Hydro Unit operating as a hydro pump. Associated with the energy market product type.
Reference to the superclass object.
undocumented
The cost to shutdown a Pump Storage Hydro Unit (in pump mode) or a pump.
The cost to shutdown a Pump Storage Hydro Unit (in pump mode) or a pump. This schedule is assocated with the hourly parameters in a resource bid associated with a specific product within the bid.
Reference to the superclass object.
undocumented
Certain skills are required and must be certified in order for a person (typically a member of a crew) to be qualified to work on types of equipment.
Certain skills are required and must be certified in order for a person (typically a member of a crew) to be qualified to work on types of equipment.
Reference to the superclass object.
Qualification identifier.
undocumented
Quality flags in this class are as defined in IEC 61850, except for estimatorReplaced, which has been included in this class for convenience.
Quality flags in this class are as defined in IEC 61850, except for estimatorReplaced, which has been included in this class for convenience.
Reference to the superclass object.
Measurement value may be incorrect due to a reference being out of calibration.
Value has been replaced by State Estimator. estimatorReplaced is not an IEC61850 quality bit but has been put in this class for convenience.
This identifier indicates that a supervision function has detected an internal or external failure, e.g. communication failure.
Measurement value is old and possibly invalid, as it has not been successfully updated during a specified time interval.
Measurement value is blocked and hence unavailable for transmission.
To prevent some overload of the communication it is sensible to detect and suppress oscillating (fast changing) binary inputs. If a signal changes in a defined time (tosc) twice in the same direction (from 0 to 1 or from 1 to 0) then oscillation is detected and the detail quality identifier "oscillatory" is set. If it is detected a configured numbers of transient changes could be passed by. In this time the validity status "questionable" is set. If after this defined numbers of changes the signal is still in the oscillating state the value shall be set either to the opposite state of the previous stable value or to a defined default value. In this case the validity status "questionable" is reset and "invalid" is set as long as the signal is oscillating. If it is configured such that no transient changes should be passed by then the validity status "invalid" is set immediately in addition to the detail quality identifier "oscillatory" (used for status information only).
Measurement value is beyond a predefined range of value.
Measurement value is beyond the capability of being represented properly. For example, a counter value overflows from maximum count back to a value of zero.
Source gives information related to the origin of a value. The value may be acquired from the process, defaulted or substituted.
A correlation function has detected that the value is not consitent with other values. Typically set by a network State Estimator.
Measurement value is transmitted for test purposes.
Validity of the measurement value.
Indicates whether unit is a reliablity must run unit: required to be on to satisfy Grid Code Reliablitiy criteria, load demand, or voltage support.
Indicates whether unit is a reliablity must run unit: required to be on to satisfy Grid Code Reliablitiy criteria, load demand, or voltage support.
Reference to the superclass object.
undocumented
Model to support processing of reliability must run units.
Model to support processing of reliability must run units.
Reference to the superclass object.
undocumented
RMR Operator's entry of the RMR requirement per market interval.
RMR Operator's entry of the RMR requirement per market interval.
Reference to the superclass object.
The lower of the original pre-dispatch or the AC run schedule (Also known as the RMR Reguirement) becomes the pre-dispatch value.
undocumented
undocumented
undocumented
undocumented
Model to support processing of reliability must run units.
Model to support processing of reliability must run units.
Reference to the superclass object.
undocumented
Model to support processing of reliability must run units.
Model to support processing of reliability must run units.
Reference to the superclass object.
undocumented
Model to support processing of reliability must run units.
Model to support processing of reliability must run units.
Reference to the superclass object.
undocumented
Model to support processing of reliability must run units.
Model to support processing of reliability must run units.
Reference to the superclass object.
undocumented
Regional transmission operator.
Regional transmission operator.
Reference to the superclass object.
This class models the information about the RUC awards
This class models the information about the RUC awards
Reference to the superclass object.
Marginal Price ($/MW) for the commodity (Regulation Up, Regulation Down, Spinning Reserve, or Non-spinning reserve) for pricing run.
major product type may include the following but not limited to: Energy Regulation Up Regulation Dn Spinning Reserve Non-Spinning Reserve Operating Reserve
undocumented
undocumented
undocumented
The RUC Award of a resource is the portion of the RUC Capacity that is not under RA or RMR contracts. The RUC Award of a resource is the portion of the RUC Capacity that is eligible for RUC Availability payment.
The RUC Capacity of a resource is the difference between (i) the RUC Schedule and (ii) the higher of the DA Schedule and the Minimum Load.
The RUC Schedule of a resource is its output level that balances the load forecast used in RUC. The RUC Schedule in RUC is similar to the DA Schedule in DAM.
undocumented
A specialized class of type AggregatedNode type.
A specialized class of type AggregatedNode type. Defines RUC Zones. A forecast region represents a collection of Nodes for which the Market operator has developed sufficient historical demand and relevant weather data to perform a demand forecast for such area. The Market Operator may further adjust this forecast to ensure that the Reliability Unit Commitment produces adequate local capacity procurement.
Reference to the superclass object.
An analog control that increase or decrease a set point value with pulses.
An analog control that increase or decrease a set point value with pulses.
Reference to the superclass object.
The ValueAliasSet used for translation of a Control value to a name.
Ramp rate as a function of resource MW output
Ramp rate as a function of resource MW output
Reference to the superclass object.
condition for the ramp rate
The condition that identifies whether a Generating Resource should be constrained from Ancillary Service provision if its Schedule or Dispatch change across Trading Hours or Trading Intervals requires more than a specified fraction of the duration of the Trading Hour or Trading Interval. Valid values are Fast/Slow
How ramp rate is applied (e.g. raise or lower, as when applied to a generation resource)
undocumented
undocumented
undocumented
Fraction specified explicitly with a numerator and denominator, which can be used to calculate the quotient.
Fraction specified explicitly with a numerator and denominator, which can be used to calculate the quotient.
Reference to the superclass object.
The part of a fraction that is below the line and that functions as the divisor of the numerator.
The part of a fraction that is above the line and signifies the number to be divided by the denominator.
A tap changer that changes the voltage ratio impacting the voltage magnitude but not the phase angle across the transformer.
A tap changer that changes the voltage ratio impacting the voltage magnitude but not the phase angle across the transformer.
Reference to the superclass object.
Tap step increment, in per cent of nominal voltage, per step position.
Specifies the regulation control mode (voltage or reactive) of the RatioTapChanger.
The tap ratio table for this ratio tap changer.
Transformer end to which this ratio tap changer belongs.
Describes a curve for how the voltage magnitude and impedance varies with the tap step.
Describes a curve for how the voltage magnitude and impedance varies with the tap step.
Reference to the superclass object.
Describes each tap step in the ratio tap changer tabular curve.
Describes each tap step in the ratio tap changer tabular curve.
Reference to the superclass object.
Table of this point.
Rational number = 'numerator' / 'denominator'.
Rational number = 'numerator' / 'denominator'.
Reference to the superclass object.
Denominator. Value 1 indicates the number is a simple integer.
Numerator.
Reactive power rating envelope versus the synchronous machine's active power, in both the generating and motoring modes.
Reactive power rating envelope versus the synchronous machine's active power, in both the generating and motoring modes. For each active power value there is a corresponding high and low reactive power limit value. Typically there will be a separate curve for each coolant condition, such as hydrogen pressure. The Y1 axis values represent reactive minimum and the Y2 axis values represent reactive maximum.
Reference to the superclass object.
The machine's coolant temperature (e.g., ambient air or stator circulating water).
The hydrogen coolant pressure
Specific value measured by a meter or other asset, or calculated by a system.
Specific value measured by a meter or other asset, or calculated by a system. Each Reading is associated with a specific ReadingType.
Reference to the superclass object.
Reason for this reading being taken.
All meter readings (sets of values) containing this reading value.
Type information for this reading value.
Interharmonics are represented as a rational number 'numerator' / 'denominator', and harmonics are represented using the same mechanism and identified by 'denominator'=1.
Interharmonics are represented as a rational number 'numerator' / 'denominator', and harmonics are represented using the same mechanism and identified by 'denominator'=1.
Reference to the superclass object.
Interharmonic denominator. Value 0 means not applicable. Value 2 is used in combination with 'numerator'=1 to represent interharmonic 1/2. Finally, value 1 indicates the harmonic of the order specified with 'numerator'.
Interharmonic numerator. Value 0 means not applicable. Value 1 is used in combination with 'denominator'=2 to represent interharmonic 1/2, and with 'denominator'=1 it represents fundamental frequency. Finally, values greater than 1 indicate the harmonic of that order (e.g., 'numerator'=5 is the fifth harmonic).
Quality of a specific reading value or interval reading value.
Quality of a specific reading value or interval reading value. Note that more than one quality may be applicable to a given reading. Typically not used unless problems or unusual conditions occur (i.e., quality for each reading is assumed to be good unless stated otherwise in associated reading quality type). It can also be used with the corresponding reading quality type to indicate that the validation has been performed and succeeded.
Reference to the superclass object.
Elaboration on the quality code.
System acting as the source of the quality code.
Date and time at which the quality code was assigned or ascertained.
Reading value to which this quality applies.
Type of this reading quality.
Detailed description for a quality of a reading value, produced by an end device or a system.
Detailed description for a quality of a reading value, produced by an end device or a system. Values in attributes allow for creation of the recommended codes to be used for identifying reading value quality codes as follows: <systemId>.<category>.<subCategory>.
Reference to the superclass object.
High-level nature of the reading value quality.
More specific nature of the reading value quality, as a further sub-categorisation of 'category'.
Identification of the system which has declared the issue with the data or provided commentary on the data.
Detailed description for a type of a reading value.
Detailed description for a type of a reading value. Values in attributes allow for the creation of recommended codes to be used for identifying reading value types as follows: <macroPeriod>.<aggregate>.<measuringPeriod>.<accumulation>.<flowDirection>.<commodity>.<measurementKind>.<interharmonic.numerator>.<interharmonic.denominator>.<argument.numerator>.<argument.denominator>.<tou>.<cpp>.<consumptionTier>.<phases>.<multiplier>.<unit>.<currency>.
Reference to the superclass object.
Accumulation behaviour of a reading over time, usually 'measuringPeriod', to be used with individual endpoints (as opposed to 'macroPeriod' and 'aggregate' that are used to describe aggregations of data from individual endpoints).
Salient attribute of the reading data aggregated from individual endpoints. This is mainly used to define a mathematical operation carried out over 'macroPeriod', but may also be used to describe an attribute of the data when the 'macroPeriod' is not defined.
Argument used to introduce numbers into the unit of measure description where they are needed (e.g., 4 where the measure needs an argument such as CEMI(n=4)). Most arguments used in practice however will be integers (i.e., 'denominator'=1).
Commodity being measured.
In case of common flat-rate pricing for power, in which all purchases are at a given rate, 'consumptionTier'=0. Otherwise, the value indicates the consumption tier, which can be used in conjunction with TOU or CPP pricing.
Critical peak period (CPP) bucket the reading value is attributed to. Value 0 means not applicable. Even though CPP is usually considered a specialised form of time of use 'tou', this attribute is defined explicitly for flexibility.
Metering-specific currency.
Flow direction for a reading where the direction of flow of the commodity is important (for electricity measurements this includes current, energy, power, and demand).
Indication of a "harmonic" or "interharmonic" basis for the measurement. Value 0 in 'numerator' and 'denominator' means not applicable.
Time period of interest that reflects how the reading is viewed or captured over a long period of time.
Identifies "what" is being measured, as refinement of 'commodity'. When combined with 'unit', it provides detail to the unit of measure. For example, 'energy' with a unit of measure of 'kWh' indicates to the user that active energy is being measured, while with 'kVAh' or 'kVArh', it indicates apparent energy and reactive energy, respectively. 'power' can be combined in a similar way with various power units of measure: Distortion power ('distortionVoltAmperes') with 'kVA' is different from 'power' with 'kVA'.
Time attribute inherent or fundamental to the reading value (as opposed to 'macroPeriod' that supplies an "adjective" to describe aspects of a time period with regard to the measurement). It refers to the way the value was originally measured and not to the frequency at which it is reported or presented. For example, an hourly interval of consumption data would have value 'hourly' as an attribute. However in the case of an hourly sampled voltage value, the meterReadings schema would carry the 'hourly' interval size information.
Metering-specific multiplier.
Metering-specific phase code.
Time of use (TOU) bucket the reading value is attributed to. Value 0 means not applicable.
Metering-specific unit.
Channel reporting/collecting register values with this type information.
Pending calculation that produced this reading type.
The motivation of an act.
The motivation of an act.
Reference to the superclass object.
The motivation of an act in coded form.
The textual explanation corresponding to the reason code.
undocumented
undocumented
Record of total receipted payment from customer.
Record of total receipted payment from customer.
Reference to the superclass object.
True if this receipted payment is manually bankable, otherwise it is an electronic funds transfer.
Receipted amount with rounding, date and note.
Cashier shift during which this receipt was recorded.
Vendor shift during which this receipt was recorded.
A reclose sequence (open and close) is defined for each possible reclosure of a breaker.
A reclose sequence (open and close) is defined for each possible reclosure of a breaker.
Reference to the superclass object.
Indicates the time lapse before the reclose step will execute a reclose.
Indicates the ordinal position of the reclose step relative to other steps in the sequence.
A breaker may have zero or more automatic reclosures after a trip occurs.
Pole-mounted fault interrupter with built-in phase and ground relays, current transformer (CT), and supplemental controls.
Pole-mounted fault interrupter with built-in phase and ground relays, current transformer (CT), and supplemental controls.
Reference to the superclass object.
Properties of recloser assets.
Properties of recloser assets.
Reference to the superclass object.
True if device has ground trip capability.
True if normal status of ground trip is enabled.
Ground trip rating.
Phase trip rating.
Total number of phase reclose operations.
Reconditioning information for an asset.
Reconditioning information for an asset.
Reference to the superclass object.
Date and time this reconditioning (or a major overhaul) has been performed.
undocumented
This class is used for handling the accompanying annotations, time stamp, author, etc.
This class is used for handling the accompanying annotations, time stamp, author, etc. of designs, drawings and maps. A red line can be associated with any Location object.
Reference to the superclass object.
undocumented
A device that indicates or records units of the commodity or other quantity measured.
A device that indicates or records units of the commodity or other quantity measured.
Reference to the superclass object.
If true, the data it produces is calculated or measured by a device other than a physical end device/meter. Otherwise, any data streams it produces are measured by the hardware of the end device/meter itself.
Number of digits (dials on a mechanical meter) to the left of the decimal place; default is normally 5.
Number of digits (dials on a mechanical meter) to the right of the decimal place.
Clock time interval for register to beging/cease accumulating time of usage (e.g., start at 8:00 am, stop at 5:00 pm).
Name used for the time of use tier (also known as bin or bucket). For example, "peak", "off-peak", "TOU Category A", etc.
End device function metering quantities displayed by this register.
Model of a generator that is registered to participate in the market
Model of a generator that is registered to participate in the market
Reference to the superclass object.
Capacity Factor
Cold start time.
Name of the Combined Cycle Plant (valid for Combined Cyle modes or configurations)
undocumented
Constrained Output Generator (COG) Indicator (Yes/No), per Generating Resource
undocumented
Some long-start up time units may need to receive start up instruction before DA market results are available. Long-Start resources may be either physical resources within the control with start-up times greater than 18 hours or the long-start contractual inter-tie commitment that shall be completed by 6 am one-day ahead. Therefore, there is a need for a process to determine the commitment of such resources before the DA market.
Values: Natural Gas Based Resource, Non Natural Gas Based Resource "NG" - Natural-Gas-Based Resource - a Resource that is powered by Natural Gas "NNG" - Non-Natural-Gas-Based Resource - a Resouce that is powered by some other fuel than Natural Gas
High limit for secondary (AGC) control
Hot-to-intermediate time (Seasonal)
Hot start time.
Intermediate-to-cold time (Seasonal)
Intermediate start time.
Provides an indication that this resource is intending to participate in the intermittent resource program.
Certifies resources for use in MSS Load Following Down
Certifies resources for use in MSS Load Following Up
Low limit for secondary (AGC) control
Regulation down response rate in MW per minute
undocumented
Maximum Dependable Capacity (MNDC).
undocumented
The registered maximum Minimum Load Cost of a Generating Resource registered with a Cost Basis of "Bid Cost".
max pumping level of a hydro pump unit
Maximum time this device can be shut down.
maximum start ups per day
Maximum weekly Energy (Seasonal)
Maximum weekly starts (seasonal parameter)
Maximum allowable spinning reserve. Spinning reserve will never be considered greater than this value regardless of the current operating point.
This is the maximum operating MW limit the dispatcher can enter for this unit
minimum load cost. Value is (currency/hr)
The cost for the fuel required to get a Generating Resource to operate at the minimum load level
This is the minimum operating MW limit the dispatcher can enter for this unit.
Flag to indicate that this unit is a resource adequacy resource and must offer.
MW value stated on the nameplate of the Generator -- the value it potentially could provide.
The portion of the Operating Cost of a Generating Resource that is not related to fuel cost.
Combined Cycle operating mode.
undocumented
The minimum down time for the pump in a pump storage unit.
The minimum up time aspect for the pump in a pump storage unit
The cost to shutdown a pump during the pump aspect of a pump storage unit.
The shutdown time (minutes) of the pump aspect of a pump storage unit.
undocumented
Pumping factor for pump storage units, conversion factor between generating and pumping.
undocumented
Quick start flag (Yes/No)
Regulation up response rate in MW per minute
undocumented
Ramp curve type: 0 - Fixed ramp rate independent of rate function unit MW output 1 - Static ramp rates as a function of unit MW output only 2 - Dynamic ramp rates as a function of unit MW output and ramping time
Ramping mode 0: ignore ramping limits 1: 20-minute ramping rule 2: 60-minute ramping rule
0 = Unit is not on regulation 1 = Unit is on AGC and regulating 2 = Unit is suppose to be on regulation but it is not under regulation now
For the outage scheduling services
CCGT90 Combined Cycle greater than 90 MW CCLE90 Combined Cycle less than or equal to 90 MW CLLIG Coal and Lignite DSL Diesel GASSTM Gas-Steam GSNONR Gas Steam Non-Reheat Boiler GSREH Gas Steam Reheat Boiler GSSUP Gas Steam Supercritical Boiler HYDRO Hydro NUC Nuclear RENEW Renewable SCGT90 Simple Cycle greater than 90 MW SCLE90 Simple Cycle less than or equal to 90 MW WIND Wind PS Pumped Storage
River System the Resource is tied to.
undocumented
Is the Resource Synchronous Condenser capable Resource?
Generating unit type: Combined Cycle, Gas Turbine, Hydro Turbine, Other, Photovoltaic, Hydro Pump-Turbine, Reciprocating Engine, Steam Turbine, Synchronous Condenser, Wind Turbine
Use limit flag: indicates if the use-limited resource is fully scheduled (or has some slack for real-time dispatch) (Y/N)
undocumented
undocumented
undocumented
undocumented
undocumented
Reliability must not run (RMNR) flag: indicated whether the RMR unit is set as an RMNR in the current market
Reliability must run (RMR) flag: indicates whether the unit is RMR; Indicates whether the unit is RMR: N' - not an RMR unit '1' - RMR Condition 1 unit '2' - RMR Condition 2 unit
undocumented
Indicates the RMR Manual pre-determination status [Y/N]
undocumented
undocumented
undocumented
undocumented
Reliability must take (RMT) flag (Yes/No): indicates whether the unit is RMT
undocumented
undocumented
undocumented
undocumented
This class represents the inter tie resource.
This class represents the inter tie resource.
Reference to the superclass object.
indicate the direction (export/import) of an intertie resource
Under each major product type, the commodity type can be applied to further specify the type.
Flag to indicated whether this Inter-tie is a DC Tie.
check if the inter-tie resource is registered for the dynamic interchange..
The registered upper bound of minimum hourly block for an Inter-Tie Resource
undocumented
undocumented
Model of a load that is registered to participate in the market (demand reduction)
Model of a load that is registered to participate in the market (demand reduction)
Reference to the superclass object.
Flag to indicate that the Resource is Block Load pseudo resource (‘Y’, ‘ N’)
Flag to indicate that a Load Resource is part of a DSR Load
Qualification status (used for DSR qualification)
Non-participating load registry as a MSS load
Maximum Base Load (MW), per Participating Load Resource
Maximum Deployment time (seconds)
Maximum Number of Daily Load Curtailments
maximum load reduction
Maxiimum Load Reduction Time (min), per Participating Load Resource
Maximum weekly deployments
Minimum MW for a load reduction (e.g., MW rating of a discrete pump. This attribute may be used also in the LoadBid class. The reason that the attribute is also modeled in this class is that it is resource attribute and needs to be persistently stored.
minimum load reduction cost. Single number for the load
Shortest period load reduction shall be maintained before load can be restored to normal levels. This attribute may be used also in the LoadBid class. The reason that the attribute is also modeled in this class is that it is resource attribute and needs to be persistently stored.
Minimum Load Reduction Time (min), per Participating Load Resource
Shortest time that load shall be left at normal levels before a new load reduction. This attribute may be used also in the LoadBid class. The reason that the attribute is also modeled in this class is that it is resource attribute and needs to be persistently stored.
Participating Load flag: indicates whether the load resource is participates in load reduction actions.
Time period that is required from an order to reduce a load to the time that it takes to get to the minimum load reduction. This attribute may be used also in the LoadBid class. The reason that the attribute is also modeled in this class is that it is resource attribute and needs to be persistently stored.
CLR Controllable Load NCLR Non-Controllable Load
undocumented
undocumented
undocumented
A Non-Participating Load Resource aggregation scheme with resource-specific Distribution Factors that are submitted with the Bid and for which the distributed Energy is settled at the relevant Distribution Location marginal prices.
A resource that is registered through the market participant registration system.
A resource that is registered through the market participant registration system. Examples include generating unit, load, and non-physical generator or load.
Reference to the superclass object.
Resource Commercial Operation Date.
contingent operating reserve availiability (Yes/No). Resource is availiable to participate with capacity in contingency dispatch.
Dispatch flag: indicates whether the resource is dispatchable (Y/N) It is move to the RegisteredResource class for the participating load dispatch purpose
end effective date
flexible offer flag (Y/N)
Indicates need to dispatch before the start of the operating hour. Only relevent in Real-Time Market. Applies to generation, intertie and participating load resource. Value (Y/N)
a flag to indicate if a resource is an aggregated resource
Indication of the last time this item was modified/versioned.
Market Participation flag: indicates whether the resource participate in the market (Y/N)
maximum base self schedule quantity
maximum on time after start up
minimum number of consecutive hours a resource shall be dispatched if bid is accepted
minimum off time after shut down
minimum on time after start up
Must offer flag: indicates whether the unit is subject to the must offer provisions (Y/N)
Flag to indicate that the Resource is not participating in the Market Operations.
Indication that the registered resource is a Point of Delivery (YES) resource which implies there is a POD Loss Factor.
Price setting flag: indicates whether a resource is capable of setting the Market Clearing Price (Y) for the DA market, and if not, indicates whether the resource shall submit bids for energy at $ 0 (S) or not (N) Initially in the RegisteredGenerator class. It wasmove to the RegisteredResource class for the participating load dispatch purpose
Price setting flag: indicates whether a resource is capable of setting the Market Clearing Price (Y) for the RT market, and if not, indicates whether the resource shall submit bids for energy at $ 0 (S) or not (N) Initially in the RegisteredGenerator class. It wasmove to the RegisteredResource class for the participating load dispatch purpose
Registration Status of resource - Active, Mothballed, Planned, or Decommissioned.
Indication that this resource participates inthe resource adequacy function.
start effective date
Indication that this resource is associated with an Adjacent Control Area
Indication that the resource participates in the optimization process by default.
undocumented
undocumented
undocumented
Indication that this resource is associated with an Embedded Control area
undocumented
undocumented
undocumented
LMPM flag: indicates whether the resource is subject to the LMPM test (Yes/No)
undocumented
undocumented
A registered resource injects power at one or more connectivity nodes related to a pnode
undocumented
undocumented
undocumented
undocumented
SMPM flag: indicates whether the resource is subject to the SMPM test (Yes/No)
undocumented
undocumented
The schedule has time points where the time between them is constant.
The schedule has time points where the time between them is constant.
Reference to the superclass object.
The time for the last time point.
The time between each pair of subsequent regular time points in sequence order.
Time point for a schedule where the time between the consecutive points is constant.
Time point for a schedule where the time between the consecutive points is constant.
Reference to the superclass object.
The position of the regular time point in the sequence. Note that time points don't have to be sequential, i.e. time points may be omitted. The actual time for a RegularTimePoint is computed by multiplying the associated regular interval schedule's time step with the regular time point sequence number and adding the associated schedules start time.
The first value at the time. The meaning of the value is defined by the derived type of the associated schedule.
The second value at the time. The meaning of the value is defined by the derived type of the associated schedule.
Regular interval schedule containing this time point.
A type of conducting equipment that can regulate a quantity (i.e.
A type of conducting equipment that can regulate a quantity (i.e. voltage or flow) at a specific point in the network.
Reference to the superclass object.
Specifies the regulation status of the equipment. True is regulating, false is not regulating.
The regulating control scheme in which this equipment participates.
Specifies a set of equipment that works together to control a power system quantity such as voltage or flow.
Specifies a set of equipment that works together to control a power system quantity such as voltage or flow. Remote bus voltage control is possible by specifying the controlled terminal located at some place remote from the controlling equipment.
Reference to the superclass object.
The regulation is performed in a discrete mode. This applies to equipment with discrete controls, e.g. tap changers and shunt compensators.
The flag tells if regulation is enabled.
The regulating control mode presently available. This specification allows for determining the kind of regulation without need for obtaining the units from a schedule.
Phase voltage controlling this regulator, measured at regulator location.
This is a deadband used with discrete control to avoid excessive update of controls like tap changers and shunt compensator banks while regulating. The units of those appropriate for the mode.
The target value specified for case input. This value can be used for the target value without the use of schedules. The value has the units appropriate to the mode attribute.
Specify the multiplier for used for the targetValue.
The terminal associated with this regulating control. The terminal is associated instead of a node, since the terminal could connect into either a topological node (bus in bus-branch model) or a connectivity node (detailed switch model). Sometimes it is useful to model regulation at a terminal of a bus bar object since the bus bar can be present in both a bus-branch model or a model with switch detail.
This class represents the physical characteristc of a generator regarding the regulating limit
This class represents the physical characteristc of a generator regarding the regulating limit
Reference to the superclass object.
undocumented
undocumented
undocumented
Special requirements and/or regulations may pertain to certain types of assets or work.
Special requirements and/or regulations may pertain to certain types of assets or work. For example, fire protection and scaffolding.
Reference to the superclass object.
External reference to regulation, if applicable.
A pre-established pattern over time for a controlled variable, e.g., busbar voltage.
A pre-established pattern over time for a controlled variable, e.g., busbar voltage.
Reference to the superclass object.
Regulating controls that have this Schedule.
Information regarding the experienced and expected reliability of a specific asset, type of asset, or asset model.
Information regarding the experienced and expected reliability of a specific asset, type of asset, or asset model.
Reference to the superclass object.
Mean time to repair (MTTR - hours).
Momentary failure rate (temporary failures/kft-year).
undocumented
undocumented
Remedial Action Scheme (RAS), Special Protection Schemes (SPS), System Protection Schemes (SPS) or System Integrity Protection Schemes (SIPS).
Remedial Action Scheme (RAS), Special Protection Schemes (SPS), System Protection Schemes (SPS) or System Integrity Protection Schemes (SIPS).
Reference to the superclass object.
The status of the class set by operation or by signal. Optional field that will override other status fields.
Kind of Remedial Action Scheme (RAS)
The default/normal value used when other active signal/values are missing.
undocumented
Details of remote connect and disconnect function.
Details of remote connect and disconnect function.
Reference to the superclass object.
Setting of the timeout elapsed time.
Voltage limit on customer side of RCD switch above which the connect should not be made.
Limit of energy before disconnect.
Start date and time to accumulate energy for energy usage limiting.
Warning energy limit, used to trigger event code that energy usage is nearing limit.
True if the RCD switch has to be armed before a connect action can be initiated.
True if the RCD switch has to be armed before a disconnect action can be initiated.
True if the energy usage is limited and the customer will be disconnected if they go over the limit.
True if load limit has to be checked to issue an immediate disconnect (after a connect) if load is over the limit.
True if voltage limit has to be checked to prevent connect if voltage is over the limit.
Load limit above which the connect should either not take place or should cause an immediate disconnect.
True if pushbutton has to be used for connect.
Remote controls are ouputs that are sent by the remote unit to actuators in the process.
Remote controls are ouputs that are sent by the remote unit to actuators in the process.
Reference to the superclass object.
The maximum set point value accepted by the remote control point.
The minimum set point value accepted by the remote control point.
Set to true if the actuator is remotely controlled.
The Control for the RemoteControl point.
Supports connection to a terminal associated with a remote bus from which an input signal of a specific type is coming.
Supports connection to a terminal associated with a remote bus from which an input signal of a specific type is coming.
Reference to the superclass object.
Type of input signal.
Discontinuous excitation control model using this remote input signal.
Power Factor or VAr controller Type I model using this remote input signal.
Power system stabilizer model using this remote input signal.
Remote terminal with which this input signal is associated.
Underexcitation limiter model using this remote input signal.
Voltage compensator model using this remote input signal.
The wind plant using the remote signal.
Wind generator Type 1 or Type 2 model using this remote input signal.
Wind turbine Type 3 or 4 models using this remote input signal.
For a RTU remote points correspond to telemetered values or control outputs.
For a RTU remote points correspond to telemetered values or control outputs. Other units (e.g. control centers) usually also contain calculated values.
Reference to the superclass object.
Remote unit this point belongs to.
Remote sources are state variables that are telemetered or calculated within the remote unit.
Remote sources are state variables that are telemetered or calculated within the remote unit.
Reference to the superclass object.
The smallest change in value to be reported.
The time interval between scans.
The maximum value the telemetry item can return.
The minimum value the telemetry item can return.
Link to the physical telemetered point associated with this measurement.
A remote unit can be a RTU, IED, substation control system, control center etc.
A remote unit can be a RTU, IED, substation control system, control center etc. The communication with the remote unit can be through various standard protocols (e.g. IEC 61870, IEC 61850) or non standard protocols (e.g. DNP, RP570 etc.). A remote unit contain remote data points that might be telemetered, collected or calculated. The RemoteUnit class inherit PowerSystemResource. The intention is to allow RemotUnits to have Measurements. These Measurements can be used to model unit status as operational, out of service, unit failure etc.
Reference to the superclass object.
Type of remote unit.
A reporting group is used for various ad-hoc groupings used for reporting.
A reporting group is used for various ad-hoc groupings used for reporting.
Reference to the superclass object.
Power system resources which belong to this reporting group.
Reporting super group to which this reporting group belongs.
A reporting super group, groups reporting groups for a higher level report.
A reporting super group, groups reporting groups for a higher level report.
Reference to the superclass object.
Reserve demand curve.
Reserve demand curve. Models maximum quantities of reserve required per Market Region and models a reserve demand curve for the minimum quantities of reserve. The ReserveDemandCurve is a relationship between unit operating reserve price in $/MWhr (Y-axis) and unit reserves in MW (X-axis).
Reference to the superclass object.
Region requirement maximum limit
Reserve requirement type that the max and curve apply to. For example, operating reserve, regulation and contingency.
undocumented
undocumented
Requirements for minimum amount of reserve and/or regulation to be supplied by a set of qualified resources.
Requirements for minimum amount of reserve and/or regulation to be supplied by a set of qualified resources.
Reference to the superclass object.
Market product associated with reserve requirement must be a reserve or regulation product.
undocumented
undocumented
A curve relating reserve requirement versus time, showing the values of a specific reserve requirement for each unit of the period covered.
A curve relating reserve requirement versus time, showing the values of a specific reserve requirement for each unit of the period covered. The curve can be based on "absolute" time or on "normalized' time.
Reference to the superclass object.
undocumented
A water storage facility within a hydro system, including: ponds, lakes, lagoons, and rivers.
A water storage facility within a hydro system, including: ponds, lakes, lagoons, and rivers. The storage is usually behind some type of dam.
Reference to the superclass object.
Storage volume between the full supply level and the normal minimum operating level.
The reservoir's energy storage rating in energy for given head conditions.
Full supply level, above which water will spill. This can be the spillway crest level or the top of closed gates.
Total capacity of reservoir.
Normal minimum operating level below which the penstocks will draw air.
River outlet works for riparian right releases or other purposes.
The spillway water travel delay to the next downstream reservoir.
Type of spillway gate, including parameters.
The flow capacity of the spillway in cubic meters per second.
The length of the spillway crest.
Spillway crest level above which water will spill.
A reservoir may spill into a downstream reservoir.
A reservoir may have a water level target schedule.
Ancillary Services that a resource is qualified to provide.
Ancillary Services that a resource is qualified to provide.
Reference to the superclass object.
Certified capacity for associated resource and market type and ancillary service type product
Ancillary Service Qualification end date
market type
Status of the qualification ('Y' = Active, 'N' = Inactive)
Ancillary Service Qualification effective from date
Type of service based on ResourceAncillaryServiceType enumeration
RegisteredResources are qualified for resource ancillary service types (which include market product types as well as other types such as BlackStart) by the association to the class ResourceAncillaryServiceQualification.
Models details of bid and offer market clearing.
Models details of bid and offer market clearing. Class indicates whether a contingency is active and whether the automatic dispatching system is active for this interval of the market solution
Reference to the superclass object.
Indication that the system is currently operating in a contingency mode.
undocumented
Model of market results, instruction for resource.
Model of market results, instruction for resource. Contains details of award as attributes
Reference to the superclass object.
For DA Energy: Not Applicable; For DA AS: DA AS market award; For RT Energy: Not Applicable; For RT AS: RT AS market award (excluding DA AS market or self-proviison awards)
For DA Energy: Total Schedule = DA market schedule + DA self-schedule award; For DA AS: DA Ancillary Service Awards = DA AS market award + DA AS self-provision award; For RT Energy: Total Schedule = RT market schedule + RT self-schedule award; For RT AS: RT Ancillary Service Awards = RT AS self-provision award + RT AS market award + DA AS market award + DA AS self-provision award;
Marginal Price ($/MW) for the commodity (Regulation Up, Regulation Down, Spinning Reserve, or Non-spinning reserve) for pricing run.
Congestion component of Location Marginal Price (LMP) in monetary units per MW.
Cost component of Locational Marginal Pricing (LMP) in monetary units per MW.
The tier2 mw added by dispatcher action Market results of the synchronized reserve market
Unit max output for dispatch; bid in economic maximum
Unit min output for dispatch; bid in economic minimum
Effective Regulation Down Limit (MW)
Effective Regulation Up Limit
Locational marginal price value
Loss component of Location Marginal Price (LMP) in monetary units per MW.
Indicates if an award was manually blocked (Y/N). Valid for Spinning and Non-spinning.
Indicator (Yes / No) that this resource set the price for this dispatch / schedule.
Identifes if the unit was set to must run by the market participant responsible for bidding in the unit
Unit no-load cost in case of energy commodity
Optimal Bid cost
Optimal Bid production payment based on LMP
Optimal Bid production margin
Time the manual data entry occured.
Provides the ability for the grid operator to override items, such as spin capacity requirements, prior to running the algorithm. This value is market product based (spin, non-spin, reg up, reg down, or RUC).
For DA Energy: DA total self-schedule award; For DA AS: DA AS self-provision award; For RT Energy: RT total self-schedule award; For RT AS: RT AS self-provision award (excluding DA AS market or self-provision awards)
Unit start up cost in case of energy commodity
In or out status of resource
Total bid revenue (startup_cost + no_load_cost + bid_pay)
undocumented
undocumented
undocumented
undocumented
undocumented
Energy bid for generation, load, or virtual type for the whole of the market-trading period (i.e., one day in day ahead market or one hour in the real time market)
Energy bid for generation, load, or virtual type for the whole of the market-trading period (i.e., one day in day ahead market or one hour in the real time market)
Reference to the superclass object.
Aggregation flag 0: individual resource level 1: Aggregated node location 2: Aggregated price location)
undocumented
Energy product (commodity) type: 'En' - Energy 'Ru' - Regulation Up 'Rd' - Regulation Dn 'Sr' - Spinning Reserve 'Nr' - Non-Spinning Reserve 'Or' - Operating Reserve
contingent operating reserve availiability (Yes/No). Resource is availiable to participate with capacity only in contingency dispatch.
A Yes indicates that this bid was created by the ISO.
Maximum amount of energy per day which can be produced during the trading period in MWh
Minimum amount of energy per day which has to be produced during the trading period in MWh
Market Separation Flag 'Y' - Enforce market separation constraints for this bid 'N' - Don't enforce market separation constraints for this bid.
minimum number of consecutive hours a resource shall be dispatched if bid is accepted
Resource loading curve type 1 - step-wise continuous loading 2 - piece-wise linear continuous loading 3 - block loading
Maximum number of shutdowns per day.
Maximum number of shutdowns per week.
Maximum number of startups per day.
Maximum number of startups per week.
True if bid is virtual. Bid is assumed to be non-virtual if attribute is absent
undocumented
This class model the various capacities of a resource.
This class model the various capacities of a resource. A resource may have numbers of capacities related to operating, ancillary services, energy trade and so forth. The types are but not limited to:
Reference to the superclass object.
capacity type The types are but not limited to: Regulation Up Regulation Dn Spinning Reserve Non-Spinning Reserve FOO capacity MOO capacity
default capacity
maximum capacity
minimum capacity
This class represent the resource certification for a specific product type.
This class represent the resource certification for a specific product type. For example, a resource is certified for Non-Spinning reserve for RTM.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
Model of market results, including cleaing result of resources.
Model of market results, including cleaing result of resources. Associated with ResourceDispatchResults.
Reference to the superclass object.
The ResourceDispatchResults class provides market results that can be provided to a SC.
The ResourceDispatchResults class provides market results that can be provided to a SC. The specific data provided consists of several indicators such as contingency flags, blocked start up, and RMR dispatch. It also provides the projected overall and the regulating status of the resource.
Reference to the superclass object.
Blocked Dispatch Indicator (Yes/No)
Block sending DOP to ADS (Y/N)
Contingent Operating Reserve Indicator (Yes/No). Resource participating with AS capacity in contingency dispatch.
indicate which limit is the constraints
resource energy ramping lower limit
maximum ramp rate
The upper operating limit incorporating any derate used by the RTD for the Binding Interval.
The lower operating limit incorporating any derate used by the RTD for the Binding Interval.
Penalty Dispatch Indicator (Yes / No) indicating an un-economic adjustment.
The upper regulating limit incorporating any derate used by the RTD for the Binding Interval.
The lower regulating limit incorporating any derate used by the RTD for the Binding Interval.
Unit Commitment Status (On/Off/Starting)
Resource total upward schedule. total schedule = En + all AS per resource per interval
undocumented
undocumented
undocumented
resource energy ramping upper limit
undocumented
undocumented
A logical grouping of resources that are used to model location of types of requirements for ancillary services such as spinning reserve zones, regulation zones, etc.
A logical grouping of resources that are used to model location of types of requirements for ancillary services such as spinning reserve zones, regulation zones, etc.
Reference to the superclass object.
Status of this group.
Type of this group.
Ancillary service requirements for a market.
Ancillary service requirements for a market.
Reference to the superclass object.
undocumented
undocumented
Model of market clearing results for resources that bid to follow load
Model of market clearing results for resources that bid to follow load
Reference to the superclass object.
weighted average for RTPD and RTCD and same for RTID
undocumented
undocumented
Unique instruction id per instruction, assigned by the SC and provided to ADS. ADS passes through.
The start of the time interval for which requirement is defined.
undocumented
undocumented
To model the Operation and Maintenance (O and M) costs of a generation resource.
To model the Operation and Maintenance (O and M) costs of a generation resource.
Reference to the superclass object.
Percentage of Fuel Index Price (gas) for operating above Low Sustained Limit (LSL)
Percentage of Fuel Oil Price (FOP) for operating above Low Sustained Limit (LSL)
Verifiable O&M Cost ($), Cold Startup
Verifiable O&M Cost ($), Hot Startup
Verifiable O&M Cost ($), Intermediate Startup
Verifiable O&M Cost ($/MWh), LSL
Percentage of Solid Fuel for operating above Low Sustained Limit (LSL)
undocumented
To model the startup costs of a generation resource.
To model the startup costs of a generation resource.
Reference to the superclass object.
Verifiable Cold Start Up Fuel (MMBtu per start)
Verifiable Hot Start Up Fuel (MMBtu per start)
Verifiable Intermediate Start Up Fuel (MMBtu per start)
Minimum-Energy fuel, MMBtu/MWh
Percentage of Fuel Index Price (gas) for cold startup
Percentage of Fuel Index Price (gas) for hot startup
Percentage of Fuel Index Price (gas) for intermediate startup
Percentage of FIP (gas) for operating at LSL
Percentage of Fuel Oil Price (FOP) for cold startup
Percentage of Fuel Oil Price (FOP) for hot startup
Percentage of Fuel Oil Price (FOP) for intermediate startup
Percentage of FOP (oil) for operating at LSL
Percentage of Solid Fuel for cold startup
Percentage of Solid Fuel for hot startup
Percentage of Solid Fuel for intermedite startup
Percentage of Solid Fuel for operating at LSL
undocumented
This class is defined to describe the verifiable costs associated with a generation resource.
This class is defined to describe the verifiable costs associated with a generation resource.
Reference to the superclass object.
undocumented
undocumented
undocumented
A right-of-way (ROW) is for land where it is lawful to use for a public road, an electric power line, etc.
A right-of-way (ROW) is for land where it is lawful to use for a public road, an electric power line, etc. Note that the association to Location, Asset, Organisation, etc. for the Grant is inherited from Agreement, a type of Document.
Reference to the superclass object.
Property related information that describes the ROW's land parcel. For example, it may be a deed book number, deed book page number, and parcel number.
All land properties this right of way applies to.
Enumeration of potential roles that might be played by one object relative to another.
Enumeration of potential roles that might be played by one object relative to another.
Reference to the superclass object.
undocumented
Type of role.
A rotating machine which may be used as a generator or motor.
A rotating machine which may be used as a generator or motor.
Reference to the superclass object.
Active power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Reactive power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
Power factor (nameplate data). It is primarily used for short circuit data exchange according to IEC 60909.
Nameplate apparent power rating for the unit. The attribute shall have a positive value.
Rated voltage (nameplate data, Ur in IEC 60909-0). It is primarily used for short circuit data exchange according to IEC 60909.
A synchronous machine may operate as a generator and as such becomes a member of a generating unit.
The synchronous machine drives the turbine which moves the water from a low elevation to a higher elevation. The direction of machine rotation for pumping may or may not be the same as for generating.
Abstract parent class for all synchronous and asynchronous machine standard models.
Abstract parent class for all synchronous and asynchronous machine standard models.
Reference to the superclass object.
Damping torque coefficient (D). A proportionality constant that, when multiplied by the angular velocity of the rotor poles with respect to the magnetic field (frequency), results in the damping torque. This value is often zero when the sources of damping torques (generator damper windings, load damping effects, etc.) are modelled in detail. Typical Value = 0.
Inertia constant of generator or motor and mechanical load (H) (>0). This is the specification for the stored energy in the rotating mass when operating at rated speed. For a generator, this includes the generator plus all other elements (turbine, exciter) on the same shaft and has units of MW*sec. For a motor, it includes the motor plus its mechanical load. Conventional units are per unit on the generator MVA base, usually expressed as MW*second/MVA or just second. This value is used in the accelerating power reference frame for operator training simulator solutions. Typical Value = 3.
Saturation factor at rated terminal voltage (S1) (> or =0). Not used by simplified model. Defined by defined by S(E1) in the SynchronousMachineSaturationParameters diagram. Typical Value = 0.02.
Saturation factor at 120% of rated terminal voltage (S12) (> or =S1). Not used by the simplified model, defined by S(E2) in the SynchronousMachineSaturationParameters diagram. Typical Value = 0.12.
Stator leakage reactance (Xl) (> or =0). Typical Value = 0.15.
Stator (armature) resistance (Rs) (> or =0). Typical Value = 0.005.
Route that is followed, for example by service crews.
Route that is followed, for example by service crews.
Reference to the superclass object.
undocumented
Classification by utility's work management standards and practices.
undocumented
Contains information about the update from SCADA
Contains information about the update from SCADA
Reference to the superclass object.
time of the update from SCADA
SVC asset allows the capacitive and inductive ratings for each phase to be specified individually if required.
SVC asset allows the capacitive and inductive ratings for each phase to be specified individually if required.
Reference to the superclass object.
Maximum capacitive reactive power.
Maximum inductive reactive power.
Document restricting or authorising works on electrical equipment (for example a permit to work, sanction for test, limitation of access, or certificate of isolation), defined based upon organisational practices.
Document restricting or authorising works on electrical equipment (for example a permit to work, sanction for test, limitation of access, or certificate of isolation), defined based upon organisational practices.
Reference to the superclass object.
Switching plan to which this safety document applies.
A time scheduled value for apparent power limit.
A time scheduled value for apparent power limit.
Reference to the superclass object.
The apparent power limit value for the scheduled time.
A current limit that is scheduled.
A current limit that is scheduled.
Reference to the superclass object.
The current flow limit value applicable at the scheduled time.
An event to trigger one or more activities, such as reading a meter, recalculating a bill, requesting work, when generating units must be scheduled for maintenance, when a transformer is scheduled to be refurbished, etc.
An event to trigger one or more activities, such as reading a meter, recalculating a bill, requesting work, when generating units must be scheduled for maintenance, when a transformer is scheduled to be refurbished, etc.
Reference to the superclass object.
Duration of the scheduled event, for example, the time to ramp between values.
undocumented
Type of scheduled event.
undocumented
Specification for this scheduled event.
Schedule parameters for an activity that is to occur, is occurring, or has completed.
Schedule parameters for an activity that is to occur, is occurring, or has completed.
Reference to the superclass object.
Estimated date and time for activity execution (with earliest possibility of activity initiation and latest possibility of activity completion).
Requested date and time interval for activity execution.
undocumented
undocumented
A limit that is applicable during a scheduled time period.
A limit that is applicable during a scheduled time period.
Reference to the superclass object.
undocumented
The season for which the scheduled limits applies. If not specified, then applicable ot any season.
A voltage limit value for a scheduled time.
A voltage limit value for a scheduled time.
Reference to the superclass object.
The voltage limit value for the scheduled time.
Market participants could be represented by Scheduling Coordinators (SCs) that are registered with the RTO/ISO.
Market participants could be represented by Scheduling Coordinators (SCs) that are registered with the RTO/ISO. One participant could register multiple SCs with the RTO/ISO. Many market participants can do business with the RTO/ISO using a single SC. One SC could schedule multiple generators. A load scheduling point could be used by multiple SCs. Each SC could schedule load at multiple scheduling points. An inter-tie scheduling point can be used by multiple SCs. Each SC can schedule interchange at multiple inter-tie scheduling points.
Reference to the superclass object.
This is the short name or Scheduling Coordinator ID field.
undocumented
undocumented
Describing users of a Scheduling Coordinator
Describing users of a Scheduling Coordinator
Reference to the superclass object.
undocumented
Login ID Expiration Date
Login ID
Assigned roles (these are roles with either Read or Read/Write privileges on different Market Systems)
Login ID Effective Date
Connection to other organizations at the boundary of the ISO/RTO.
Connection to other organizations at the boundary of the ISO/RTO.
Reference to the superclass object.
End effective date.
Start effective date.
undocumented
Physically controls access to AssetContainers.
Physically controls access to AssetContainers.
Reference to the superclass object.
Date and time this seal has been applied.
Condition of seal.
Kind of seal.
(reserved word) Seal number.
Asset container to which this seal is applied.
A specified time period of the year.
A specified time period of the year.
Reference to the superclass object.
Date season ends.
Date season starts.
A time schedule covering a 24 hour period, with curve data for a specific type of season and day.
A time schedule covering a 24 hour period, with curve data for a specific type of season and day.
Reference to the superclass object.
DayType for the Schedule.
Season for the Schedule.
Automatic switch that will lock open to isolate a faulted section.
Automatic switch that will lock open to isolate a faulted section. It may, or may not, have load breaking capability. Its primary purpose is to provide fault sectionalising at locations where the fault current is either too high, or too low, for proper coordination of fuses.
Reference to the superclass object.
Typically provided by RTO systems, constraints identified in both base case and critical contingency cases have to be transferred.
Typically provided by RTO systems, constraints identified in both base case and critical contingency cases have to be transferred. A constraint has N (>=1) constraint terms. A term is represented by an
Reference to the superclass object.
undocumented
undocumented
undocumented
Typical for regional transmission operators (RTOs), these constraints include transmission as well as generation group constraints identified in both base case and critical contingency cases.
Typical for regional transmission operators (RTOs), these constraints include transmission as well as generation group constraints identified in both base case and critical contingency cases.
Reference to the superclass object.
Actual branch or group of branches MW flow (only for transmission constraints)
Maximum MW limit
Minimum MW limit (only for transmission constraints).
undocumented
undocumented
undocumented
Binding security constrained clearing results posted for a given settlement period.
Binding security constrained clearing results posted for a given settlement period.
Reference to the superclass object.
Optimal MW flow
Binding MW limit.
Security constraint shadow price.
Model of Self Schedules Results.
Model of Self Schedules Results. Includes self schedule MW,and type of self schedule for each self schedule type included in total self schedule MW value found in ResourceAwardInstruction.
Reference to the superclass object.
Cleared value for the specific self schedule type listed.
Self schedule breakdown type.
undocumented
Optionally, this curve expresses elasticity of the associated requirement.
Optionally, this curve expresses elasticity of the associated requirement. For example, used to reduce requirements when clearing price exceeds reasonable values when the supply quantity becomes scarce. For example, a single point value of $1000/MW for a spinning reserve will cause a reduction in the required spinning reserve.
Reference to the superclass object.
undocumented
This class describe devices that transform a measured quantity into signals that can be presented at displays, used in control or be recorded.
This class describe devices that transform a measured quantity into signals that can be presented at displays, used in control or be recorded.
Reference to the superclass object.
A Series Compensator is a series capacitor or reactor or an AC transmission line without charging susceptance.
A Series Compensator is a series capacitor or reactor or an AC transmission line without charging susceptance. It is a two terminal device.
Reference to the superclass object.
Positive sequence resistance.
Zero sequence resistance.
Describe if a metal oxide varistor (mov) for over voltage protection is configured at the series compensator.
The maximum current the varistor is designed to handle at specified duration.
The dc voltage at which the varistor start conducting.
Positive sequence reactance.
Zero sequence reactance.
Limit based on most restrictive series equipment limit.
Limit based on most restrictive series equipment limit. A specification of of equipment that determines the calculated operational limit values based upon other equipment and their ratings. The most restrictive limit connected in series within the group is used. The physical connection based on switch status for example may also impact which elements in the group are considered. Any equipment in the group that are presently connected in series with the equipment of the directly associated operational limit are used. This provides a means to indicate which potentially series equipment limits are considered for a computed operational limit. The operational limit of the same operational limit type is assumed to be used from the grouped equipment. It is also possible to make assumptions or calculations regarding how flow might split if the equipment is not simply in series.
Reference to the superclass object.
Category of service provided to the customer.
Category of service provided to the customer.
Reference to the superclass object.
Kind of service.
A service guarantee, often imposed by a regulator, defines conditions that, if not satisfied, will result in the utility making a monetary payment to the customer.
A service guarantee, often imposed by a regulator, defines conditions that, if not satisfied, will result in the utility making a monetary payment to the customer. Note that guarantee's identifier is in the 'name' attribute and the status of the guarantee is in the 'Status.status' attribute.
Reference to the superclass object.
Period in which this service guantee applies.
True if utility must autmatically pay the specified amount whenever the condition is not satisified, otherwise customer must make a claim to receive payment.
Amount to be paid by the service provider to the customer for each violation of the 'serviceRequirement'.
Explanation of the requirement and conditions for satisfying it.
A real estate location, commonly referred to as premises.
A real estate location, commonly referred to as premises.
Reference to the superclass object.
Method for the service person to access this service location. For example, a description of where to obtain a key if the facility is unmanned and secured.
True if inspection is needed of facilities at this service location. This could be requested by a customer, due to suspected tampering, environmental concerns (e.g., a fire in the vicinity), or to correct incompatible data.
Problems previously encountered when visiting or performing work on this location. Examples include: bad dog, violent customer, verbally abusive occupant, obstructions, safety hazards, etc.
Multiplier applied at the usage point.
Multiplier applied at the usage point.
Reference to the superclass object.
Kind of multiplier.
Multiplier value.
Usage point applying this multiplier.
The defined termination points of a transmission path (down to distribution level or to a customer - generation or consumption or both).
The defined termination points of a transmission path (down to distribution level or to a customer - generation or consumption or both). Service points are defined from the viewpoint of the transmission service. Each service point is contained within (or on the boundary of) an interchange area. A service point is source or destination of a transaction.
Reference to the superclass object.
Summary counts of service points affected by an outage.
Summary counts of service points affected by an outage. These counts are sometimes referred to as total and critical customer count.
Reference to the superclass object.
Number of critical service (delivery) points affected by an outage.
Number of all service (delivery) points affected by an outage.
Organisation that provides services to customers.
Organisation that provides services to customers.
Reference to the superclass object.
Unique transaction reference prefix number issued to an entity by the International Organization for Standardization for the purpose of tagging onto electronic financial transactions, as defined in ISO/IEC 7812-1 and ISO/IEC 7812-2.
Kind of supplier.
An analog control that issue a set point value.
An analog control that issue a set point value.
Reference to the superclass object.
Normal value for Control.value e.g. used for percentage scaling.
The value representing the actuator output.
Specifies a settlement run.
Specifies a settlement run.
Reference to the superclass object.
The trade date on which the settlement is run.
undocumented
Generally referring to a period of operation or work performed.
Generally referring to a period of operation or work performed. Whether the shift is open/closed can be derived from attributes 'activityInterval.start' and 'activityInterval.end'.
Reference to the superclass object.
Interval for activity of this shift.
Total of amounts receipted during this shift that can be manually banked (cash and cheques for example). Values are obtained from Receipt attributes:
Total of amounts receipted during this shift that cannot be manually banked (card payments for example). Values are obtained from Receipt attributes:
Cumulative amount in error due to process rounding not reflected in receiptsGrandTotal. Values are obtained from Receipt attributes:
Cumulative total of transacted amounts during this shift. Values are obtained from transaction:
Cumulative amount in error due to process rounding not reflected in transactionsGandTotal. Values are obtained from Transaction attributes:
The patterns of shifts worked by people or crews.
The patterns of shifts worked by people or crews.
Reference to the superclass object.
Type of assignement intended to be worked on this shift, for example, temporary, standard, etc.
Number of cycles for a temporary shift.
undocumented
Date and time interval for which this shift pattern is valid (when it became effective and when it expires).
Short-circuit test results determine mesh impedance parameters.
Short-circuit test results determine mesh impedance parameters. They include load losses and leakage impedances. For three-phase windings, the excitation can be a positive sequence (the default) or a zero sequence. There shall be at least one grounded winding.
Reference to the superclass object.
Tap step number for the energised end of the test pair.
Tap step number for the grounded end of the test pair.
Leakage impedance measured from a positive-sequence or single-phase short-circuit test.
Leakage impedance measured from a zero-sequence short-circuit test.
Load losses from a positive-sequence or single-phase short-circuit test.
Load losses from a zero-sequence short-circuit test.
Transformer end that voltage is applied to in this short-circuit test. The test voltage is chosen to induce rated current in the energised end.
A shunt capacitor or reactor or switchable bank of shunt capacitors or reactors.
A shunt capacitor or reactor or switchable bank of shunt capacitors or reactors. A section of a shunt compensator is an individual capacitor or reactor. A negative value for reactivePerSection indicates that the compensator is a reactor. ShuntCompensator is a single terminal device. Ground is implied.
Reference to the superclass object.
Time delay required for the device to be connected or disconnected by automatic voltage regulation (AVR).
Used for Yn and Zn connections. True if the neutral is solidly grounded.
The maximum number of sections that may be switched in.
The voltage at which the nominal reactive power may be calculated. This should normally be within 10% of the voltage at which the capacitor is connected to the network.
The normal number of sections switched in.
The type of phase connection, such as wye or delta.
Shunt compensator sections in use. Starting value for steady state solution. Non integer values are allowed to support continuous variables. The reasons for continuous value are to support study cases where no discrete shunt compensators has yet been designed, a solutions where a narrow voltage band force the sections to oscillate or accommodate for a continuous solution as input.
The switch on count since the capacitor count was last reset or initialized.
The date and time when the capacitor bank was last switched on.
Voltage sensitivity required for the device to regulate the bus voltage, in voltage/reactive power.
The state for the number of shunt compensator sections in service.
Distribution capacitor bank control settings.
Distribution capacitor bank control settings.
Reference to the superclass object.
For VAR, amp, or power factor locally controlled shunt impedances, the flow direction: in, out.
The size of the individual units that make up the bank.
Kind of control (if any).
For locally controlled shunt impedances which have a voltage override feature, the high voltage override value. If the voltage is above this value, the shunt impedance will be turned off regardless of the other local controller settings.
Kind of local controller.
Upper control setting.
Lower control setting.
True if the locally controlled capacitor has voltage override capability.
For locally controlled shunt impedances which have a voltage override feature, the low voltage override value. If the voltage is below this value, the shunt impedance will be turned on regardless of the other local controller settings.
IdmsShuntImpedanceData.maxNumSwitchOps.
True if open is normal status for a fixed capacitor bank, otherwise normal status is closed.
For VAR, amp, or power factor locally controlled shunt impedances, the index of the regulation branch.
For VAR, amp, or power factor locally controlled shunt impedances, the end of the branch that is regulated. The field has the following values: from side, to side, and tertiary (only if the branch is a transformer).
(For VAR, amp, or power factor locally controlled shunt impedances) Kind of regulation branch.
Phases that are measured for controlling the device.
Time interval between consecutive switching operations.
True if regulated voltages are measured line to line, otherwise they are measured line to ground.
undocumented
Optimal Power Flow or State Estimator Filter Bank Data for OTS.
Optimal Power Flow or State Estimator Filter Bank Data for OTS. This is used for RealTime, Study and Maintenance Users
Reference to the superclass object.
The current status for the Voltage Control Capacitor 1= Connected 0 = Disconnected
The desired voltage for the Voltage Control Capacitor
The injection of reactive power of the filter bank in the NA solution or VCS reactive power production
Voltage control capacitor step position
Indicator if the voltage control this is regulating True = Yes, False = No
undocumented
Properties of shunt capacitor, shunt reactor or switchable bank of shunt capacitor or reactor assets.
Properties of shunt capacitor, shunt reactor or switchable bank of shunt capacitor or reactor assets.
Reference to the superclass object.
Maximum allowed apparent power loss.
Rated current.
Rated reactive power.
Rated voltage.
undocumented
Single phase of a multi-phase shunt compensator when its attributes might be different per phase.
Single phase of a multi-phase shunt compensator when its attributes might be different per phase.
Reference to the superclass object.
The maximum number of sections that may be switched in for this phase.
For the capacitor phase, the normal number of sections switched in.
Phase of this shunt compensator component. If the shunt compensator is wye connected, the connection is from the indicated phase to the central ground or neutral point. If the shunt compensator is delta connected, the phase indicates a shunt compensator connected from the indicated phase to the next logical non-neutral phase.
Shunt compensator of this shunt compensator phase.
Relationship between the rate in gross active power/minute (Y-axis) at which a unit should be shutdown and its present gross MW output (X-axis).
Relationship between the rate in gross active power/minute (Y-axis) at which a unit should be shutdown and its present gross MW output (X-axis).
Reference to the superclass object.
Fixed shutdown cost.
The date and time of the most recent generating unit shutdown.
A thermal generating unit may have a shutdown curve.
Simple end device function distinguished by 'kind'.
Simple end device function distinguished by 'kind'. Use this class for instances that cannot be represented by another end device function specialisations.
Reference to the superclass object.
Kind of this function.
Proficiency level of a craft, which is required to operate or maintain a particular type of asset and/or perform certain types of work.
Proficiency level of a craft, which is required to operate or maintain a particular type of asset and/or perform certain types of work.
Reference to the superclass object.
Interval between the certification and its expiry.
Date and time the skill became effective.
Level of skill for a Craft.
undocumented
undocumented
undocumented
A solar thermal generating unit.
A solar thermal generating unit.
Reference to the superclass object.
Specification can be used for various purposes relative to an asset, a logical device (PowerSystemResource), location, etc.
Specification can be used for various purposes relative to an asset, a logical device (PowerSystemResource), location, etc. Examples include documents supplied by manufacturers such as asset installation instructions, asset maintenance instructions, etc.
Reference to the superclass object.
Stage of a remedial action scheme.
Stage of a remedial action scheme.
Reference to the superclass object.
The priority of the stage. 0 = don t care (default) 1 = highest priority. 2 is less than 1 and so on. A stage with higher priority needs be activated before a lower stage can be activated.
undocumented
Condition that is triggered either by TriggerCondition of by gate condition within a stage and has remedial action-s.
Condition that is triggered either by TriggerCondition of by gate condition within a stage and has remedial action-s.
Reference to the superclass object.
The status of the class set by operation or by signal. Optional field that will override other status fields.
The default/normal value used when other active signal/values are missing.
Priority of trigger. 0 = don t care (default) 1 = highest priority. 2 is less than 1 and so on. A trigger with the highest priority will trigger first.
undocumented
undocumented
undocumented
undocumented
undocumented
The Standard Industrial Classification (SIC) are the codes that identify the type of products/service an industry is involved in, and used for statutory reporting purposes.
The Standard Industrial Classification (SIC) are the codes that identify the type of products/service an industry is involved in, and used for statutory reporting purposes. For example, in the USA these codes are located by the federal government, and then published in a book entitled "The Standard Industrial Classification Manual". The codes are arranged in a hierarchical structure.
Reference to the superclass object.
Standard alphanumeric code assigned to a particular product/service within an industry.
The quantity of ignition fuel (Y-axis) used to restart and repay the auxiliary power consumed versus the number of hours (X-axis) the unit was off line.
The quantity of ignition fuel (Y-axis) used to restart and repay the auxiliary power consumed versus the number of hours (X-axis) the unit was off line.
Reference to the superclass object.
Type of ignition fuel.
The unit's startup model may have a startup ignition fuel curve.
The quantity of main fuel (Y-axis) used to restart and repay the auxiliary power consumed versus the number of hours (X-axis) the unit was off line.
The quantity of main fuel (Y-axis) used to restart and repay the auxiliary power consumed versus the number of hours (X-axis) the unit was off line.
Reference to the superclass object.
Type of main fuel.
The unit's startup model may have a startup main fuel curve.
Rate in gross active power/minute (Y-axis) at which a unit can be loaded versus the number of hours (X-axis) the unit was off line.
Rate in gross active power/minute (Y-axis) at which a unit can be loaded versus the number of hours (X-axis) the unit was off line.
Reference to the superclass object.
The startup ramp rate in gross for a unit that is on hot standby.
The unit's startup model may have a startup ramp curve.
Startup costs and time as a function of down time.
Startup costs and time as a function of down time. Relationship between unit startup cost (Y1-axis) vs. unit elapsed down time (X-axis).
Reference to the superclass object.
undocumented
The energy consumption of a generating resource to complete a start-up from the StartUpEnergyCurve.
The energy consumption of a generating resource to complete a start-up from the StartUpEnergyCurve. Definition of the StartUpEnergyCurve includes, xvalue as the cooling time and y1value as the MW value.
Reference to the superclass object.
undocumented
The fuel consumption of a Generating Resource to complete a Start-Up.(x=cooling time) Form Startup Fuel Curve.
The fuel consumption of a Generating Resource to complete a Start-Up.(x=cooling time) Form Startup Fuel Curve. xAxisData -> cooling time, y1AxisData -> MBtu
Reference to the superclass object.
undocumented
Startup time curve as a function of down time, where time is specified in minutes.
Startup time curve as a function of down time, where time is specified in minutes. Relationship between unit startup time (Y1-axis) vs. unit elapsed down time (X-axis).
Reference to the superclass object.
undocumented
Unit start up characteristics depending on how long the unit has been off line.
Unit start up characteristics depending on how long the unit has been off line.
Reference to the superclass object.
Fixed maintenance cost.
The amount of heat input per time uint required for hot standby operation.
Incremental maintenance cost.
The minimum number of hours the unit must be down before restart.
The minimum number of hours the unit must be operating before being allowed to shut down.
The opportunity cost associated with the return in monetary unit. This represents the restart's "share" of the unit depreciation and risk of an event which would damage the unit.
Total miscellaneous start up costs.
The date and time of the most recent generating unit startup.
Startup priority within control area where lower numbers indicate higher priorities. More than one unit in an area may be assigned the same priority.
The unit's auxiliary active power consumption to maintain standby mode.
The unit's startup model may have a startup ignition fuel curve.
The unit's startup model may have a startup main fuel curve.
The unit's startup model may have a startup ramp curve.
A thermal generating unit may have a startup model.
An abstract class for state variables.
An abstract class for state variables.
Reference to the superclass object.
A facility for providing variable and controllable shunt reactive power.
A facility for providing variable and controllable shunt reactive power. The SVC typically consists of a stepdown transformer, filter, thyristor-controlled reactor, and thyristor-switched capacitor arms.
Reference to the superclass object.
Maximum available capacitive reactance.
Maximum available inductive reactance.
Reactive power injection. Load sign convention is used, i.e. positive sign means flow out from a node.
SVC control mode.
The characteristics slope of an SVC defines how the reactive power output changes in proportion to the difference between the regulated bus voltage and the voltage setpoint.
The reactive power output of the SVC is proportional to the difference between the voltage at the regulated bus and the voltage setpoint. When the regulated bus voltage is equal to the voltage setpoint, the reactive power output is zero.
Station supply with load derived from the station output.
Station supply with load derived from the station output.
Reference to the superclass object.
Current status information relevant to an entity.
Current status information relevant to an entity.
Reference to the superclass object.
Date and time for which status 'value' applies.
Reason code or explanation for why an object went to the current status 'value'.
Pertinent information regarding the current 'value', as free form text.
Status value at 'dateTime'; prior status changes may have been kept in instances of activity records associated with the object to which this status applies.
The cogeneration plant's steam sendout schedule in volume per time unit.
The cogeneration plant's steam sendout schedule in volume per time unit.
Reference to the superclass object.
A cogeneration plant has a steam sendout schedule.
Steam supply for steam turbine.
Steam supply for steam turbine.
Reference to the superclass object.
Rating of steam supply.
Steam turbines may have steam supplied by a steam supply.
Steam turbine.
Steam turbine.
Reference to the superclass object.
Crossover time constant.
First reheater time constant.
Second reheater time constant.
Fraction of power from shaft 1 high pressure turbine output.
Fraction of power from shaft 1 intermediate pressure turbine output.
Fraction of power from shaft 1 first low pressure turbine output.
Fraction of power from shaft 1 second low pressure turbine output.
Fraction of power from shaft 2 high pressure turbine output.
Fraction of power from shaft 2 intermediate pressure turbine output.
Fraction of power from shaft 2 first low pressure turbine output.
Fraction of power from shaft 2 second low pressure turbine output.
Steam chest time constant.
General purpose street address information.
General purpose street address information.
Reference to the superclass object.
Status of this address.
Street detail.
Town detail.
Street details, in the context of address.
Street details, in the context of address.
Reference to the superclass object.
Additional address information, for example a mailstop.
(if applicable) In certain cases the physical location of the place of interest does not have a direct point of entry from the street, but may be located inside a larger structure such as a building, complex, office block, apartment, etc.
(if applicable) Utilities often make use of external reference systems, such as those of the town-planner's department or surveyor general's mapping system, that allocate global reference codes to streets.
Name of the street.
Designator of the specific location on the street.
Prefix to the street name. For example: North, South, East, West.
Suffix to the street name. For example: North, South, East, West.
Number of the apartment or suite.
Type of street. Examples include: street, circle, boulevard, avenue, road, drive, etc.
True if this street is within the legal geographical boundaries of the specified town (default).
Streetlight asset.
Streetlight asset.
Reference to the superclass object.
Length of arm. Note that a new light may be placed on an existing arm.
Lamp kind.
Power rating of light.
Pole to which thiss streetlight is attached.
StringMeasurement represents a measurement with values of type string.
StringMeasurement represents a measurement with values of type string.
Reference to the superclass object.
StringMeasurementValue represents a measurement value of type string.
StringMeasurementValue represents a measurement value of type string.
Reference to the superclass object.
The value to supervise.
Measurement to which this value is connected.
Quantity with string value (when it is not important whether it is an integral or a floating point number) and associated unit information.
Quantity with string value (when it is not important whether it is an integral or a floating point number) and associated unit information.
Reference to the superclass object.
undocumented
undocumented
undocumented
Construction holding assets such as conductors, transformers, switchgear, etc.
Construction holding assets such as conductors, transformers, switchgear, etc. Where applicable, number of conductors can be derived from the number of associated wire spacing instances.
Reference to the superclass object.
Date fumigant was last applied.
Name of fumigant.
Visible height of structure above ground level for overhead construction (e.g., Pole or Tower) or below ground level for an underground vault, manhole, etc. Refer to associated DimensionPropertiesInfo for other types of dimensions.
Material this structure is made of.
Maximum rated voltage of the equipment that can be mounted on/contained within the structure.
True if weeds are to be removed around asset.
Date weed were last removed.
Support for structure assets.
Support for structure assets.
Reference to the superclass object.
(if anchor) Kind of anchor.
(if anchor) Number of rods used.
(if anchor) Length of rod used.
Direction of this support structure.
Kind of structure support.
Length of this support structure.
Size of this support structure.
undocumented
An area defined for the purpose of tracking interchange with surrounding areas via tie points; may or may not serve as a control area.
An area defined for the purpose of tracking interchange with surrounding areas via tie points; may or may not serve as a control area.
Reference to the superclass object.
Market area short name, which is the regulation zone. It references AGC regulation zone name.
Loss estimate constant coefficient
Used in conjunction with the InternalCA flag. If the InternalCA flag is YES, this flag does not apply. If the InternaCA flag is NO, this flag provides an indication of AdjacentCA (NO) or Embedded CA (YES).
end effective date
A Yes/No indication that this control area is contained internal to the system.
Loss estimate linear coefficient
Indication that this control area is the local control area.
Maximum amount of self schedule MWs allowed for an embedded control area.
Minimum amount of self schedule MW allowed for an embedded control area.
Loss estimate quadratic coefficient
start effective date
undocumented
undocumented
The interchange area may operate as a control area
undocumented
A subset of a geographical region of a power system network model.
A subset of a geographical region of a power system network model.
Reference to the superclass object.
The geographical region to which this sub-geographical region is within.
The class is the second level in a hierarchical structure for grouping of loads for the purpose of load flow load scaling.
The class is the second level in a hierarchical structure for grouping of loads for the purpose of load flow load scaling.
Reference to the superclass object.
The LoadArea where the SubLoadArea belongs.
Once-through subcritical boiler.
Once-through subcritical boiler.
Reference to the superclass object.
Price curve for specifying the cost of energy (X) at points in time (y1) according to a prcing structure, which is based on a tariff.
Price curve for specifying the cost of energy (X) at points in time (y1) according to a prcing structure, which is based on a tariff.
Reference to the superclass object.
A collection of equipment for purposes other than generation or utilization, through which electric energy in bulk is passed for the purposes of switching or modifying its characteristics.
A collection of equipment for purposes other than generation or utilization, through which electric energy in bulk is passed for the purposes of switching or modifying its characteristics.
Reference to the superclass object.
The SubGeographicalRegion containing the substation.
List of resources that can be substituted for within the bounds of a Contract definition.
List of resources that can be substituted for within the bounds of a Contract definition. This class has a precedence and a resource.
Reference to the superclass object.
An indicator of the order a resource should be substituted. The lower the number the higher the precedence.
undocumented
undocumented
Once-through supercritical boiler.
Once-through supercritical boiler.
Reference to the superclass object.
Shunt device, installed on the network, usually in the proximity of electrical equipment in order to protect the said equipment against transient voltage transients caused by lightning or switching activity.
Shunt device, installed on the network, usually in the proximity of electrical equipment in order to protect the said equipment against transient voltage transients caused by lightning or switching activity.
Reference to the superclass object.
Properties of surge arrester.
Properties of surge arrester.
Reference to the superclass object.
Maximum continuous power frequency voltage allowed on the surge arrester.
If true, the arrester has a polymer housing, porcelain otherwise.
Residual voltage during an 8x20 microsecond current impulse at the nominal discharge current level.
Determines the arrester energy discharge capability. Choices are limited to 0 (none) through 5 (highest) by IEC 60099. Classes 1..3 require a 10-kA nominal discharge current. Classes 4..5 require a 20-kA nominal discharge current. Lower nominal discharge currents must use class 0.
The lightning discharge current used to classify the arrester. Choices are limited to 1.5, 2.5, 5, 10, and 20 kA by IEC 60099.
Fault current level at which all parts of the failed arrester lie within a circle prescribed by IEC 60099.
The temporary overvoltage (TOV) level at power frequency that the surge arrester withstands for 10 seconds.
Residual voltage during a current impulse with front time of 1 microsecond, and magnitude equal to the nominal discharge current level.
Residual voltage during a current impulse with front time of at least 30 microseconds, and magnitude specified in IEC 60099 for the line discharge class. Does not apply to line discharge class 0.
The SvInjection is reporting the calculated bus injection minus the sum of the terminal flows.
The SvInjection is reporting the calculated bus injection minus the sum of the terminal flows. The terminal flow is positive out from the bus (load sign convention) and bus injection has positive flow into the bus. SvInjection may have the remainder after state estimation or slack after power flow calculation.
Reference to the superclass object.
The active power injected into the bus in addition to injections from equipment terminals. Positive sign means injection into the TopologicalNode (bus).
The reactive power injected into the bus in addition to injections from equipment terminals. Positive sign means injection into the TopologicalNode (bus).
The topological node associated with the flow injection state variable.
State variable for power flow.
State variable for power flow. Load convention is used for flow direction. This means flow out from the TopologicalNode into the equipment is positive.
Reference to the superclass object.
The active power flow. Load sign convention is used, i.e. positive sign means flow out from a TopologicalNode (bus) into the conducting equipment.
The reactive power flow. Load sign convention is used, i.e. positive sign means flow out from a TopologicalNode (bus) into the conducting equipment.
The terminal associated with the power flow state variable.
State variable for the number of sections in service for a shunt compensator.
State variable for the number of sections in service for a shunt compensator.
Reference to the superclass object.
The number of sections in service as a continous variable. To get integer value scale with ShuntCompensator.bPerSection.
The shunt compensator for which the state applies.
State variable for status.
State variable for status.
Reference to the superclass object.
The in service status as a result of topology processing.
The conducting equipment associated with the status state variable.
State variable for transformer tap step.
State variable for transformer tap step. This class is to be used for taps of LTC (load tap changing) transformers, not fixed tap transformers.
Reference to the superclass object.
The floating point tap position. This is not the tap ratio, but rather the tap step position as defined by the related tap changer model and normally is constrained to be within the range of minimum and maximum tap positions.
The tap changer associated with the tap step state.
State variable for voltage.
State variable for voltage.
Reference to the superclass object.
The voltage angle of the topological node complex voltage with respect to system reference.
The voltage magnitude of the topological node.
The topological node associated with the voltage state.
A generic device designed to close, or open, or both, one or more electric circuits.
A generic device designed to close, or open, or both, one or more electric circuits. All switches are two terminal devices including grounding switches.
Reference to the superclass object.
The attribute is used in cases when no Measurement for the status value is present. If the Switch has a status measurement the Discrete.normalValue is expected to match with the Switch.normalOpen.
The attribute tells if the switch is considered open when used as input to topology processing.
The maximum continuous current carrying capacity in amps governed by the device material and construction.
Branch is retained in a bus branch model. The flow through retained switches will normally be calculated in power flow.
The switch on count since the switch was last reset or initialized.
The date and time when the switch was last switched on.
Composite switch to which this Switch belongs.
Current outage of this protective device.
Action changing status of this switch.
Action on switch as a switching step.
Action on switch as a switching step.
Reference to the superclass object.
Switching action to perform.
Switch that is the object of this switch action.
Planned outage for whose scope this switch action applies.
Group to which this step belongs.
Switch data.
Switch data.
Reference to the superclass object.
The maximum fault current a breaking device can break safely under prescribed conditions of use.
If true, it is a single phase switch.
If true, the switch is not ganged (i.e., a switch phase may be operated separately from other phases).
Rated current.
Rated voltage.
Single phase of a multi-phase switch when its attributes might be different per phase.
Single phase of a multi-phase switch when its attributes might be different per phase.
Reference to the superclass object.
The attribute tells if the switch is considered closed when used as input to topology processing.
Used in cases when no Measurement for the status value is present. If the SwitchPhase has a status measurement the Discrete.normalValue is expected to match with this value.
Phase of this SwitchPhase on the side with terminal sequence number equal 1. Should be a phase contained in that terminal’s phases attribute.
Phase of this SwitchPhase on the side with terminal sequence number equal 2. Should be a phase contained in that terminal’s Terminal.phases attribute.
The switch of the switch phase.
A schedule of switch positions.
A schedule of switch positions. If RegularTimePoint.value1 is 0, the switch is open. If 1, the switch is closed.
Reference to the superclass object.
A SwitchSchedule is associated with a Switch.
Optimal Power Flow or State Estimator Circuit Breaker Status.
Optimal Power Flow or State Estimator Circuit Breaker Status.
Reference to the superclass object.
Circuit Breaker Status (closed or open) of the circuit breaker from the power flow.
undocumented
A sequence of grouped or atomic steps intended to: - de-energise equipment or part of the network for safe work, and/or - bring back in service previously de-energised equipment or part of the network.
A sequence of grouped or atomic steps intended to: - de-energise equipment or part of the network for safe work, and/or - bring back in service previously de-energised equipment or part of the network.
Reference to the superclass object.
Purpose of this plan, such as whether it is to move the state from normal to some abnormal condition, or to restore the normal state after an abnormal condition, or to perform some kind of optimisation such as correction of overload, voltage control, etc.
Ranking in comparison to other switching plans.
Outage that will be eliminated when this switching plan gets executed.
Atomic switching step; can be part of a switching step group, or of the switching plan.
Atomic switching step; can be part of a switching step group, or of the switching plan.
Reference to the superclass object.
Free text description of this activity.
Actual date and time of this switching step.
If true, the sequence number serves for presentation purposes only, and the activity itself may be executed at any time.
Planned date and time of this switching step.
Order of this activity in the sequence of activities within the switching plan.
Crew member responsible for this switching step.
Operator responsible for this switching step.
A logical step, grouping atomic switching steps that are important to distinguish when they may change topology (e.g.
A logical step, grouping atomic switching steps that are important to distinguish when they may change topology (e.g. placing a jumper between two cuts).
Reference to the superclass object.
If true, the sequence number serves for presentation purposes only, and the activity itself may be executed at any time.
Order of this activity in the sequence of activities within the switching plan.
Switching plan to which this group belongs.
A device that operates when two AC circuits are within the desired limits of frequency, phase angle, and voltage, to permit or to cause the paralleling of these two circuits.
A device that operates when two AC circuits are within the desired limits of frequency, phase angle, and voltage, to permit or to cause the paralleling of these two circuits. Used to prevent the paralleling of non-synchronous topological islands.
Reference to the superclass object.
The maximum allowable voltage vector phase angle difference across the open device.
The maximum allowable frequency difference across the open device.
The maximum allowable difference voltage across the open device.
An electromechanical device that operates with shaft rotating synchronously with the network.
An electromechanical device that operates with shaft rotating synchronously with the network. It is a single machine operating either as a generator or synchronous condenser or pump.
Reference to the superclass object.
Time delay required when switching from Automatic Voltage Regulation (AVR) to Manual for a lagging MVAr violation.
Time delay required when switching from Automatic Voltage Regulation (AVR) to Manual for a leading MVAr violation.
Default base reactive power value. This value represents the initial reactive power that can be used by any application function.
Active power consumed when in condenser mode operation.
Temperature or pressure of coolant medium
Method of cooling the machine.
Indicates whether or not the generator is earthed. Used for short circuit data exchange according to IEC 60909
Generator star point earthing resistance (Re). Used for short circuit data exchange according to IEC 60909
Generator star point earthing reactance (Xe). Used for short circuit data exchange according to IEC 60909
Steady-state short-circuit current (in A for the profile) of generator with compound excitation during 3-phase short circuit.
Time delay required when switching from Manual to Automatic Voltage Regulation. This value is used in the accelerating power reference frame for powerflow solutions
Maximum reactive power limit. This is the maximum (nameplate) limit for the unit.
Maximum voltage limit for the unit.
Minimum reactive power limit for the unit.
Minimum voltage limit for the unit.
Factor to calculate the breaking current (Section 4.5.2.1 in the IEC 60909-0). Used only for single fed short circuit on a generator (Section 4.3.4.2. in the IEC 60909-0).
Current mode of operation.
Percent of the coordinated reactive control that comes from this machine.
Equivalent resistance (RG) of generator. RG is considered for the calculation of all currents, except for the calculation of the peak current ip. Used for short circuit data exchange according to IEC 60909
Zero sequence resistance of the synchronous machine.
Negative sequence resistance.
Priority of unit for use as powerflow voltage phase angle reference bus selection. 0 = don t care (default) 1 = highest priority. 2 is less than 1 and so on.
Direct-axis subtransient reactance saturated, also known as Xd"sat.
Direct-axes saturated synchronous reactance (xdsat); reciprocal of short-circuit ration. Used for short circuit data exchange, only for single fed short circuit on a generator. (Section 4.3.4.2. in the IEC 60909-0).
Saturated Direct-axis transient reactance. The attribute is primarily used for short circuit calculations according to ANSI.
Type of rotor, used by short circuit applications, only for single fed short circuit according to IEC 60909.
Modes that this synchronous machine can operate in.
Range of generator voltage regulation (PG in the IEC 60909-0) used for calculation of the impedance correction factor KG defined in IEC 60909-0 This attribute is used to describe the operating voltage of the generating unit.
Zero sequence reactance of the synchronous machine.
Negative sequence reactance.
The default reactive capability curve for use by a synchronous machine.
Synchronous machine dynamics model used to describe dynamic behavior of this synchronous machine.
All synchronous machine detailed types use a subset of the same data parameters and input/output variables.
All synchronous machine detailed types use a subset of the same data parameters and input/output variables. The several variations differ in the following ways:
Reference to the superclass object.
Ratio (Exciter voltage/Generator voltage) of Efd bases of exciter and generator models. Typical Value = 1.
Excitation base system mode. It should be equal to the value of WLMDV given by the user. WLMDV is the per unit ratio between the field voltage and the excitation current: Efd = WLMDV*Ifd. Typical Value = ifag.
Q-axis saturation factor at 120% of rated terminal voltage (S12q) (>=S1q). Typical Value = 0.12.
Q-axis saturation factor at rated terminal voltage (S1q) (>= 0). Typical Value = 0.02.
Synchronous machine whose behaviour is described by reference to a standard model expressed in one of the following forms:
Synchronous machine whose behaviour is described by reference to a standard model expressed in one of the following forms:
<font color="#0f0f0f">or by definition of a user-defined model.</font> <font color="#0f0f0f"> </font><font color="#0f0f0f">Note: It is a common practice to represent small generators by a negative load rather than by a dynamic generator model when performing dynamics simulations. In this case a SynchronousMachine in the static model is not represented by anything in the dynamics model, instead it is treated as ordinary load.</font>
Reference to the superclass object.
Excitation system model associated with this synchronous machine model.
Mechanical load model associated with this synchronous machine model.
Synchronous machine to which synchronous machine dynamics model applies.
Turbine-governor model associated with this synchronous machine model.
The electrical equations for all variations of the synchronous models are based on the SynchronousEquivalentCircuit diagram for the direct and quadrature axes.
The electrical equations for all variations of the synchronous models are based on the SynchronousEquivalentCircuit diagram for the direct and quadrature axes.
Equations for conversion between Equivalent Circuit and Time Constant Reactance forms: Xd = Xad + Xl X�d = Xl + Xad * Xfd / (Xad + Xfd) X�d = Xl + Xad * Xfd * X1d / (Xad * Xfd + Xad * X1d + Xfd * X1d) Xq = Xaq + Xl X�q = Xl + Xaq * X1q / (Xaq+ X1q) X�q = Xl + Xaq * X1q* X2q / (Xaq * X1q + Xaq * X2q + X1q * X2q) T�do = (Xad + Xfd) / (omega0 * Rfd) T�do = (Xad * Xfd + Xad * X1d + Xfd * X1d) / (omega0 * R1d * (Xad + Xfd) T�qo = (Xaq + X1q) / (omega0 * R1q) T�qo = (Xaq * X1q + Xaq * X2q + X1q * X2q)/ (omega0 * R2q * (Xaq + X1q) Same equations using CIM attributes from SynchronousMachineTimeConstantReactance class on left of = sign and SynchronousMachineEquivalentCircuit class on right (except as noted): xDirectSync = xad + RotatingMachineDynamics.statorLeakageReactance xDirectTrans = RotatingMachineDynamics.statorLeakageReactance + xad * xfd / (xad + xfd) xDirectSubtrans = RotatingMachineDynamics.statorLeakageReactance + xad * xfd * x1d / (xad * xfd + xad * x1d + xfd * x1d) xQuadSync = xaq + RotatingMachineDynamics.statorLeakageReactance xQuadTrans = RotatingMachineDynamics.statorLeakageReactance + xaq * x1q / (xaq+ x1q) xQuadSubtrans = RotatingMachineDynamics.statorLeakageReactance + xaq * x1q* x2q / (xaq * x1q + xaq * x2q + x1q * x2q) tpdo = (xad + xfd) / (2*pi*nominal frequency * rfd) tppdo = (xad * xfd + xad * x1d + xfd * x1d) / (2*pi*nominal frequency * r1d * (xad + xfd) tpqo = (xaq + x1q) / (2*pi*nominal frequency * r1q) tppqo = (xaq * x1q + xaq * x2q + x1q * x2q)/ (2*pi*nominal frequency * r2q * (xaq + x1q). Are only valid for a simplified model where "Canay" reactance is zero.
Reference to the superclass object.
D-axis damper 1 winding resistance.
Q-axis damper 1 winding resistance.
Q-axis damper 2 winding resistance.
Field winding resistance.
D-axis damper 1 winding leakage reactance.
Q-axis damper 1 winding leakage reactance.
Q-axis damper 2 winding leakage reactance.
D-axis mutual reactance.
Q-axis mutual reactance.
Differential mutual (�Canay�) reactance.
Field winding leakage reactance.
The simplified model represents a synchronous generator as a constant internal voltage behind an impedance (Rs + jXp) as shown in the Simplified diagram.
The simplified model represents a synchronous generator as a constant internal voltage behind an impedance (Rs + jXp) as shown in the Simplified diagram. Since internal voltage is held constant, there is no Efd input and any excitation system model will be ignored. There is also no Ifd output.
Reference to the superclass object.
Synchronous machine detailed modelling types are defined by the combination of the attributes SynchronousMachineTimeConstantReactance.modelType and SynchronousMachineTimeConstantReactance.rotorType.
Synchronous machine detailed modelling types are defined by the combination of the attributes SynchronousMachineTimeConstantReactance.modelType and SynchronousMachineTimeConstantReactance.rotorType. Parameter notes:
The parameters used for models expressed in time constant reactance form include:
Reference to the superclass object.
Saturation loading correction factor (Ks) (>= 0). Used only by Type J model. Typical Value = 0.
Type of synchronous machine model used in Dynamic simulation applications.
Type of rotor on physical machine.
Damping time constant for �Canay� reactance. Typical Value = 0.
Direct-axis transient rotor time constant (T'do) (> Tdo). Typical Value = 5.
Direct-axis subtransient rotor time constant (Tdo) (> 0). Typical Value = 0.03.
Quadrature-axis subtransient rotor time constant (Tqo) (> 0). Typical Value = 0.03.
Quadrature-axis transient rotor time constant (T'qo) (> Tqo). Typical Value = 0.5.
Direct-axis subtransient reactance (unsaturated) (Xd) (> Xl). Typical Value = 0.2.
Direct-axis synchronous reactance (Xd) (>= X'd). The quotient of a sustained value of that AC component of armature voltage that is produced by the total direct-axis flux due to direct-axis armature current and the value of the AC component of this current, the machine running at rated speed. Typical Value = 1.8.
Direct-axis transient reactance (unsaturated) (X'd) (> =Xd). Typical Value = 0.5.
Quadrature-axis subtransient reactance (Xq) (> Xl). Typical Value = 0.2.
Quadrature-axis synchronous reactance (Xq) (> =X'q). The ratio of the component of reactive armature voltage, due to the quadrature-axis component of armature current, to this component of current, under steady state conditions and at rated frequency. Typical Value = 1.6.
Quadrature-axis transient reactance (X'q) (> =Xq). Typical Value = 0.3.
Synchronous machine whose dynamic behaviour is described by a user-defined model.
Synchronous machine whose dynamic behaviour is described by a user-defined model.
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
This class models the system distribution factors.
This class models the system distribution factors. This class needs to be used along with the HostControlArea and the ConnectivityNode to show the distribution of each individual party.
Reference to the superclass object.
Used to calculate load "participation" of a connectivity node in an host control area
undocumented
undocumented
Transmission Access Charge Area.
Transmission Access Charge Area. Charges assessed, on behalf of the Participating Transmission Owner, to parties who require access to the controlled grid.
Reference to the superclass object.
end effective date
start effective date
This class describe the sending (providing) side in a bilateral ICCP data exchange.
This class describe the sending (providing) side in a bilateral ICCP data exchange. Hence the ICCP bilateral (table) descriptions are created by exchanging ICCPProvider data between the parties.
Reference to the superclass object.
Specifies the version of the Bilateral Table configuration that is being exchanged.
Used to indicate if the Provider is responsible for initiating the TASE.2 connection. If the value is TRUE, the provider is responsible for establishing the association. If the value is FALSE, the peer provider of the Bilateral Table will need to establish the association.
Specifies the ICC scope name that the remote can use to access the information in the Bilateral Table if the information is not VCC scoped. This value may not be null.
Specifies the version of the TASE.2 that is needed to access the Bilateral Table information via TASE.2
A Transmission Right(TR) can be a chain of TR's or on individual.
A Transmission Right(TR) can be a chain of TR's or on individual. When a transmission right is not a chain, this is formally the ETC/TOR Entitlement for each ETC/TOR contract with the inclusion of CVR(Converted Rights) as an ETC. This is the sum of all entitlements on all related transmission interfaces for the same TR.
Reference to the superclass object.
The entitlement
Operating date and hour when the entitlement applies
undocumented
Action on operation tag as a switching step.
Action on operation tag as a switching step.
Reference to the superclass object.
Kind of tag action.
Tag associated with this tag action.
Group to which this step belongs.
Relationship between tailbay head loss hight (y-axis) and the total discharge into the power station's tailbay volume per time unit (x-axis) .
Relationship between tailbay head loss hight (y-axis) and the total discharge into the power station's tailbay volume per time unit (x-axis) . There could be more than one curve depending on the level of the tailbay reservoir or river level.
Reference to the superclass object.
A hydro generating unit has a tailbay loss curve.
Mechanism for changing transformer winding tap positions.
Mechanism for changing transformer winding tap positions.
Reference to the superclass object.
Specifies the regulation status of the equipment. True is regulating, false is not regulating.
Highest possible tap step position, advance from neutral. The attribute shall be greater than lowStep.
For an LTC, the delay for initial tap changer operation (first step change)
Lowest possible tap step position, retard from neutral
Specifies whether or not a TapChanger has load tap changing capabilities.
The neutral tap step position for this winding. The attribute shall be equal or greater than lowStep and equal or less than highStep.
Voltage at which the winding operates at the neutral tap setting.
The tap step position used in "normal" network operation for this winding. For a "Fixed" tap changer indicates the current physical tap setting.
Tap changer position. Starting step for a steady state solution. Non integer values are allowed to support continuous tap variables. The reasons for continuous value are to support study cases where no discrete tap changers has yet been designed, a solutions where a narrow voltage band force the tap step to oscillate or accommodate for a continuous solution as input.
For an LTC, the delay for subsequent tap changer operation (second and later step changes)
The tap step state associated with the tap changer.
The regulating control scheme in which this tap changer participates.
Describes behavior specific to tap changers, e.g.
Describes behavior specific to tap changers, e.g. how the voltage at the end of a line varies with the load level and compensation of the voltage drop by tap adjustment.
Reference to the superclass object.
Maximum allowed regulated voltage on the PT secondary, regardless of line drop compensation. Sometimes referred to as first-house protection.
If true, the line drop compensation is to be applied.
Line drop compensator resistance setting for normal (forward) power flow.
Line drop compensator reactance setting for normal (forward) power flow.
Line drop compensator resistance setting for reverse power flow.
Line drop compensator reactance setting for reverse power flow.
Optimal Power Flow or State Estimator Phase Shifter Data.
Optimal Power Flow or State Estimator Phase Shifter Data. This is used for RealTime, Study and Maintenance Users. SE Solution Phase Shifter Measurements from the last run of SE
Reference to the superclass object.
True means the phase shifter is regulating.
Phase Shifter Desired MW. The active power regulation setpoint of the phase shifter
The desired voltage for the LTC
The maximum phase angle shift of the phase shifter
The minimum phase angle shift of the phase shifter
Phase Shifter Angle. The solved phase angle shift of the phase shifter
Tap position of the phase shifter, high-side tap position of the transformer, or low-side tap position of the transformer
Indicator if the LTC transformer is regulating True = Yes, False = No
undocumented
Tap changer data.
Tap changer data.
Reference to the superclass object.
Basic Insulation Level (BIL) expressed as the impulse crest voltage of a nominal wave, typically 1.2 X 50 microsecond. This is a measure of the ability of the insulation to withstand very high voltage surges.
Built-in current transformer primary rating.
Built-in current transducer ratio.
Frequency at which the ratings apply.
Highest possible tap step position, advance from neutral.
Whether this tap changer has under load tap changing capabilities.
Lowest possible tap step position, retard from neutral.
The neutral tap step position for the winding.
Voltage at which the winding operates at the neutral tap setting.
Built-in voltage transducer ratio.
Rated apparent power.
Rated current.
Rated voltage.
Phase shift per step position.
Tap step increment, in per cent of rated voltage, per step position.
A pre-established pattern over time for a tap step.
A pre-established pattern over time for a tap step.
Reference to the superclass object.
A TapSchedule is associated with a TapChanger.
Tape shield cable data.
Tape shield cable data.
Reference to the superclass object.
Percentage of the tape shield width that overlaps in each wrap, typically 10% to 25%.
Thickness of the tape shield, before wrapping.
Reservoir water level targets from advanced studies or "rule curves".
Reservoir water level targets from advanced studies or "rule curves". Typically in one hour increments for up to 10 days.
Reference to the superclass object.
High target level limit, above which the reservoir operation will be penalized.
Low target level limit, below which the reservoir operation will be penalized.
A reservoir may have a water level target schedule.
Document, approved by the responsible regulatory agency, listing the terms and conditions, including a schedule of prices, under which utility services will be provided.
Document, approved by the responsible regulatory agency, listing the terms and conditions, including a schedule of prices, under which utility services will be provided. It has a unique number within the state or province. For rate schedules it is frequently allocated by the affiliated Public utilities commission (PUC).
Reference to the superclass object.
(if tariff became inactive) Date tariff was terminated.
Date tariff was activated.
All tariff profiles using this tariff.
A schedule of charges; structure associated with Tariff that allows the definition of complex tarif structures such as step and time of use when used in conjunction with TimeTariffInterval and Charge.
A schedule of charges; structure associated with Tariff that allows the definition of complex tarif structures such as step and time of use when used in conjunction with TimeTariffInterval and Charge. Inherited 'status.value' is defined in the context of the utility's business rules, for example: active, inactive, etc.
Reference to the superclass object.
The frequency at which the tariff charge schedule is repeated. Examples are: once off on a specified date and time; hourly; daily; weekly; monthly; 3-monthly; 6-monthly; 12-monthly; etc. At the end of each cycle, the business rules are reset to start from the beginning again.
All consumption tariff intervals used to define this tariff profile.
All time tariff intervals used to define this tariff profile.
Telephone number.
Telephone number.
Reference to the superclass object.
Area or region code.
(if applicable) City code.
Country code.
(if applicable) Extension for this telephone number.
Main (local) part of this telephone number.
A point on a table of limit verses temperature.
A point on a table of limit verses temperature.
Reference to the superclass object.
The scaling of the operational limit in percent.
The temperature of the table point.
undocumented
This is a table lookup that provides limit values corresponding to a temperature input.
This is a table lookup that provides limit values corresponding to a temperature input.
Reference to the superclass object.
This describes the coefficients of a polynomial function that has temperature as input and calculates limit values as output.
This describes the coefficients of a polynomial function that has temperature as input and calculates limit values as output.
Reference to the superclass object.
The polinomial coefficent of power 0.
The polinomial coefficent of power 1.
The polinomial coefficent of power 2.
The polinomial coefficent of power 3.
The polinomial coefficent of power 4.
Models 10-Minutes Auxillary Data
Models 10-Minutes Auxillary Data
Reference to the superclass object.
undocumented
undocumented
undocumented
Tender is what is "offered" by the customer towards making a payment and is often more than the required payment (hence the need for 'change').
Tender is what is "offered" by the customer towards making a payment and is often more than the required payment (hence the need for 'change'). The payment is thus that part of the Tender that goes towards settlement of a particular transaction.
Reference to the superclass object.
Amount tendered by customer.
Difference between amount tendered by customer and the amount charged by point of sale.
Kind of tender from customer.
Card used to tender payment.
Cheque used to tender payment.
Receipt that recorded this receiving of a payment in the form of tenders.
An AC electrical connection point to a piece of conducting equipment.
An AC electrical connection point to a piece of conducting equipment. Terminals are connected at physical connection points called connectivity nodes.
Reference to the superclass object.
Represents the normal network phasing condition. If the attribute is missing three phases (ABC or ABCN) shall be assumed.
undocumented
The conducting equipment of the terminal. Conducting equipment have terminals that may be connected to other conducting equipment terminals via connectivity nodes or topological nodes.
The connectivity node to which this terminal connects with zero impedance.
The power flow state variable associated with the terminal.
The topological node associated with the terminal. This can be used as an alternative to the connectivity node path to topological node, thus making it unneccesary to model connectivity nodes in some cases. Note that the if connectivity nodes are in the model, this association would probably not be used as an input specification.
A constraint term associated with a specific terminal on a physical piece of equipment.
A constraint term associated with a specific terminal on a physical piece of equipment.
Reference to the superclass object.
undocumented
Test results, usually obtained by a lab or other independent organisation.
Test results, usually obtained by a lab or other independent organisation.
Reference to the superclass object.
Conclusion drawn from test results.
Identifier of specimen used in inspection or test.
Date and time the specimen was received by the lab.
A diagram object for placing free-text or text derived from an associated domain object.
A diagram object for placing free-text or text derived from an associated domain object.
Reference to the superclass object.
The text that is displayed by this text diagram object.
A generating unit whose prime mover could be a steam turbine, combustion turbine, or diesel engine.
A generating unit whose prime mover could be a steam turbine, combustion turbine, or diesel engine.
Reference to the superclass object.
Operating and maintenance cost for the thermal unit.
A thermal generating unit may be a member of a compressed air energy storage plant.
A thermal generating unit may be a member of a cogeneration plant.
A thermal generating unit may be a member of a combined cycle plant.
A thermal generating unit may have a heat input curve.
A thermal generating unit may have a heat rate curve.
A thermal generating unit may have an incremental heat rate curve.
A thermal generating unit may have a shutdown curve.
A thermal generating unit may have a startup model.
A flow specification in terms of location and direction for a control area.
A flow specification in terms of location and direction for a control area.
Reference to the superclass object.
True if the flow into the terminal (load convention) is also flow into the control area. For example, this attribute should be true if using the tie line terminal further away from the control area. For example to represent a tie to a shunt component (like a load or generator) in another area, this is the near end of a branch and this attribute would be specified as false.
The control area of the tie flows.
The terminal to which this tie flow belongs.
Site of an interface between interchange areas.
Site of an interface between interchange areas. The tie point can be a network branch (e.g., transmission line or transformer) or a switching device. For transmission lines, the interchange area boundary is usually at a designated point such as the middle of the line. Line end metering is then corrected for line losses.
Reference to the superclass object.
The MW rating of the tie point.
Interval between two times.
Interval between two times.
Reference to the superclass object.
End time of this interval.
Start time of this interval.
A point in time within a sequence of points in time relative to a time schedule.
A point in time within a sequence of points in time relative to a time schedule.
Reference to the superclass object.
Absolute date and time for this time point. For calendar-based time point, it is typically manually entered, while for interval-based or sequence-based time point it is derived.
(if interval-based) A point in time relative to scheduled start time in 'TimeSchedule.scheduleInterval.start'.
(if sequence-based) Relative sequence number for this time point.
Status of this time point.
Interval defining the window of time that this time point is valid (for example, seasonal, only on weekends, not on weekends, only 8:00 am to 5:00 pm, etc.).
Time schedule owning this time point.
Description of anything that changes through time.
Description of anything that changes through time. Time schedule is used to perform a single-valued function of time. Use inherited 'type' attribute to give additional information on this schedule, such as: periodic (hourly, daily, weekly, monthly, etc.), day of the month, by date, calendar (specific times and dates).
Reference to the superclass object.
True if this schedule is deactivated (disabled).
The offset from midnight (i.e., 0 h, 0 min, 0 s) for the periodic time points to begin. For example, for an interval meter that is set up for five minute intervals ('recurrencePeriod'=300=5 min), setting 'offset'=120=2 min would result in scheduled events to read the meter executing at 2 min, 7 min, 12 min, 17 min, 22 min, 27 min, 32 min, 37 min, 42 min, 47 min, 52 min, and 57 min past each hour.
Interval at which the scheduled action repeats (e.g., first Monday of every month, last day of the month, etc.).
Duration between time points, from the beginning of one period to the beginning of the next period. Note that a device like a meter may have multiple interval periods (e.g., 1 min, 5 min, 15 min, 30 min, or 60 min).
Schedule date and time interval.
A set of regular time-ordered measurements or values of quantitative nature of an individual or collective phenomenon taken at successive, in most cases equidistant, periods / points of time.
A set of regular time-ordered measurements or values of quantitative nature of an individual or collective phenomenon taken at successive, in most cases equidistant, periods / points of time.
Reference to the superclass object.
The identification of the nature of the time series.
An indicator stating that the TimeSeries, identified by the mRID, is cancelled as well as all the values sent in a previous version of the TimeSeries in a previous document.
The coded representation of the type of curve being described.
Identification of the object that is the common dominator used to aggregate a time series.
The type of the product such as Power, energy, reactive power, transport capacity that is the subject of the time series.
Version of the time series.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
One of a sequence of time intervals defined in terms of real time.
One of a sequence of time intervals defined in terms of real time. It is typically used in association with TariffProfile to define the intervals in a time of use tariff structure, where startDateTime simultaneously determines the starting point of this interval and the ending point of the previous interval.
Reference to the superclass object.
A sequential reference that defines the identity of this interval and its relative position with respect to other intervals in a sequence of intervals.
A real time marker that defines the starting time (typically it is the time of day) for this interval. The interval extends to the start of the next interval or until it is reset to the start of the first interval by TariffProfile.tariffCycle.
All charges used to define this time tariff interval.
Tool asset.
Tool asset.
Reference to the superclass object.
(if applicable) Date the tool was last calibrated.
An electrically connected subset of the network.
An electrically connected subset of the network. Topological islands can change as the current network state changes: e.g. due to
Reference to the superclass object.
The angle reference for the island. Normally there is one TopologicalNode that is selected as the angle reference for each island. Other reference schemes exist, so the association is typically optional.
For a detailed substation model a topological node is a set of connectivity nodes that, in the current network state, are connected together through any type of closed switches, including jumpers.
For a detailed substation model a topological node is a set of connectivity nodes that, in the current network state, are connected together through any type of closed switches, including jumpers. Topological nodes change as the current network state changes (i.e., switches, breakers, etc. change state).
Reference to the superclass object.
The active power injected into the bus at this location in addition to injections from equipment. Positive sign means injection into the TopologicalNode (bus).
The reactive power injected into the bus at this location in addition to injections from equipment. Positive sign means injection into the TopologicalNode (bus).
The island for which the node is an angle reference. Normally there is one angle reference node for each island.
The base voltage of the topologocial node.
The connectivity node container to which the toplogical node belongs.
The reporting group to which the topological node belongs.
The injection flows state variables associated with the topological node.
The state voltage associated with the topological node.
A topological node belongs to a topological island.
Tower asset.
Tower asset. Dimensions of the Tower are specified in associated DimensionsInfo class.
Reference to the superclass object.
Construction structure on the tower.
Town details, in the context of address.
Town details, in the context of address.
Reference to the superclass object.
Town code.
Name of the country.
Town name.
Town section. For example, it is common for there to be 36 sections per township.
Name of the state or province.
Inter Scheduling Coordinator Trades to model financial trades which may impact settlement
Inter Scheduling Coordinator Trades to model financial trades which may impact settlement
Reference to the superclass object.
The validated and current market accepted trade amount of a physical energy trade.
MW quantity submitted by counter SC for the same trade
The Depend On IST Name points to the unique IST Name in the chain of physical energy trades.
Time and date the trade was last modified.
undocumented
Start time and date for which trade applies.
Stop time and date for which trade is applicable.
undocumented
Timestamp of submittal of submit From Scheduling Coordinator Trade to Market Participant Bid Submittal
Userid of the submit From Scheduling Coordinator trade
undocumented
Timestamp of submittal of submit To Scheduling Coordinator Trade to Market Participant Bid Submittal
Userid of the submit To Scheduling Coordinator trade
tradeQuantity: If tradeType = IST, The amount of an Energy Trade. If tradeType = AST, The amount of an Ancillary Service Obligation Trade.
Resulting status of the trade following the rule engine processing.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
Trade error and warning messages associated with the rule engine processing of the submitted trade.
Trade error and warning messages associated with the rule engine processing of the submitted trade.
Reference to the superclass object.
hour wihthin the trade for which the error applies
error message
Priority number for the error message
Timestamp of logged error/warning message
Rule identifier which triggered the error/warning message
hour wihthin the trade for which the error applies
undocumented
TradeType TradeProduct IST (InterSC Trade) PHY (Physical Energy Trade) IST APN (Energy Trades at Aggregated Pricing Nodes) IST CPT (Converted Physical Energy Trade) AST (Ancilliary Services Trade) RUT (Regulation Up Trade) AST RDT (Regulation Down Trade) AST SRT (Spinning Reserve Trade) AST NRT (Non-Spinning Reserve Trade) UCT (Unit Commitment Trade) null
TradeType TradeProduct IST (InterSC Trade) PHY (Physical Energy Trade) IST APN (Energy Trades at Aggregated Pricing Nodes) IST CPT (Converted Physical Energy Trade) AST (Ancilliary Services Trade) RUT (Regulation Up Trade) AST RDT (Regulation Down Trade) AST SRT (Spinning Reserve Trade) AST NRT (Non-Spinning Reserve Trade) UCT (Unit Commitment Trade) null
Reference to the superclass object.
PHY (Physical Energy Trade); APN (Energy Trades at Aggregated Pricing Nodes); CPT (Converted Physical Energy Trade); RUT (Regulation Up Trade); RDT (Regulation Down Trade); SRT (Spinning Reserve Trade); NRT (Non-Spinning Reserve Trade)
IST - InterSC Trade; AST - Ancilliary Services Trade; UCT - Unit Commitment Trade
Models prices at Trading Hubs, interval based
Models prices at Trading Hubs, interval based
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
Models prices at Trading Hubs
Models prices at Trading Hubs
Reference to the superclass object.
Utilizes the Market type. For DA, the price is hourly. For RTM the price is a 5 minute price.
undocumented
undocumented
The record of details of payment for service or token sale.
The record of details of payment for service or token sale.
Reference to the superclass object.
Formal reference for use with diverse payment (traffic fine for example).
Reference to the entity that is the source of 'amount' (for example: customer for token purchase; or supplier for free issue token).
Kind of transaction.
Transaction amount, rounding, date and note for this transaction line.
Reference to the entity that is the recipient of 'amount' (for example, supplier for service charge payment; or tax receiver for VAT).
(if 'kind' is transactionReversal) Reference to the original transaction that is being reversed by this transaction.
Actual amount of service units that is being paid for.
Number of service units not reflected in 'serviceUnitsEnergy' due to process rounding or truncating errors.
Auxiliary account for this payment transaction.
Cashier shift during which this transaction was recorded.
Customer account for this payment transaction.
Meter for this vending transaction.
Pricing structure applicable for this transaction.
The receipted payment for which this transaction has been recorded.
Vendor shift during which this transaction was recorded.
Bilateral or scheduled transactions for energy and ancillary services considered by market clearing process
Bilateral or scheduled transactions for energy and ancillary services considered by market clearing process
Reference to the superclass object.
Set true if this is a demand transaction.
Set true if this is a dispatchable transaction.
Set true if this is a willing to pay transaction. This flag is used to determine whether a schedule is willing-to-pay-congestion or not.
undocumented
undocumented
undocumented
Contains the intervals relavent for the associated TransactionBidResults.
Contains the intervals relavent for the associated TransactionBidResults. For example, Day Ahead cleared results for the transaction bids for each interval of the market day.
Reference to the superclass object.
Contains the cleared results for each TransactionBid submitted to and accepted by the market.
Contains the cleared results for each TransactionBid submitted to and accepted by the market.
Reference to the superclass object.
The market transaction megawatt
The price of the market transaction
undocumented
undocumented
The entity that ultimately executes the transaction and which is in control of the process; typically this is embodied in secure software running on a server that may employ secure hardware encryption devices for secure transaction processing.
The entity that ultimately executes the transaction and which is in control of the process; typically this is embodied in secure software running on a server that may employ secure hardware encryption devices for secure transaction processing.
Reference to the superclass object.
A Transfer Interface is made up of branches such as transmission lines and transformers.
A Transfer Interface is made up of branches such as transmission lines and transformers.
Reference to the superclass object.
undocumented
undocumented
TNA Interface Definitions from OPF for VSA
TNA Interface Definitions from OPF for VSA
Reference to the superclass object.
The margin for the interface
Post Transfer MW for step
Transfer Interface + Limit Attribute Usage: The absoloute of the maximum flow on the transfer interface. This is a positive MW value.
undocumented
undocumented
undocumented
The transformer core admittance.
The transformer core admittance. Used to specify the core admittance of a transformer in a manner that can be shared among power transformers.
Reference to the superclass object.
Magnetizing branch susceptance (B mag). The value can be positive or negative.
Zero sequence magnetizing branch susceptance.
Magnetizing branch conductance (G mag).
Zero sequence magnetizing branch conductance.
Transformer end datasheet used to calculate this core admittance.
A conducting connection point of a power transformer.
A conducting connection point of a power transformer. It corresponds to a physical transformer winding terminal. In earlier CIM versions, the TransformerWinding class served a similar purpose, but this class is more flexible because it associates to terminal but is not a specialization of ConductingEquipment.
Reference to the superclass object.
Core shunt magnetizing susceptance in the saturation region.
Number for this transformer end, corresponding to the end's order in the power transformer vector group or phase angle clock number. Highest voltage winding should be 1. Each end within a power transformer should have a unique subsequent end number. Note the transformer end number need not match the terminal sequence number.
(for Yn and Zn connections) True if the neutral is solidly grounded.
The reference voltage at which the magnetizing saturation measurements were made
Core magnetizing saturation curve knee flux level.
(for Yn and Zn connections) Resistance part of neutral impedance where 'grounded' is true.
(for Yn and Zn connections) Reactive part of neutral impedance where 'grounded' is true.
Base voltage of the transformer end. This is essential for PU calculation.
Core admittance of this transformer end, representing magnetising current and core losses. The full values of the transformer should be supplied for one transformer end only.
Phase tap changer associated with this transformer end.
Ratio tap changer associated with this transformer end.
(accurate for 2- or 3-winding transformers only) Pi-model impedances of this transformer end. By convention, for a two winding transformer, the full values of the transformer should be entered on the high voltage end (endNumber=1).
Terminal of the power transformer to which this transformer end belongs.
Transformer end data.
Transformer end data.
Reference to the superclass object.
Kind of connection.
Apparent power that the winding can carry under emergency conditions (also called long-term emergency power).
Number for this transformer end, corresponding to the end's order in the PowerTransformer.vectorGroup attribute. Highest voltage winding should be 1.
Basic insulation level voltage rating.
Winding phase angle where 360 degrees are represented with clock hours, so the valid values are {0, ..., 11}. For example, to express the second winding in code 'Dyn11', set attributes as follows: 'endNumber'=2, 'connectionKind' = Yn and 'phaseAngleClock' = 11.
DC resistance.
Normal apparent power rating.
Rated voltage: phase-phase for three-phase windings, and either phase-phase or phase-neutral for single-phase windings.
Apparent power that this winding can carry for a short period of time (in emergency).
Core admittance calculated from this transformer end datasheet, representing magnetising current and core losses. The full values of the transformer should be supplied for one transformer end info only.
All mesh impedances between this 'from' and other 'to' transformer ends.
Transformer star impedance calculated from this transformer end datasheet.
Transformer tank data that this end description is part of.
Transformer mesh impedance (Delta-model) between transformer ends.
Transformer mesh impedance (Delta-model) between transformer ends. The typical case is that this class describes the impedance between two transformer ends pair-wise, i.e. the cardinalities at both tranformer end associations are 1. But in cases where two or more transformer ends are modeled the cardinalities are larger than 1.
Reference to the superclass object.
Resistance between the 'from' and the 'to' end, seen from the 'from' end.
Zero-sequence resistance between the 'from' and the 'to' end, seen from the 'from' end.
Reactance between the 'from' and the 'to' end, seen from the 'from' end.
Zero-sequence reactance between the 'from' and the 'to' end, seen from the 'from' end.
From end this mesh impedance is connected to. It determines the voltage reference.
'from' transformer end datasheet this mesh impedance is calculated from. It determines the voltage reference.
Common information captured during transformer inspections and/or diagnostics.
Common information captured during transformer inspections and/or diagnostics. Note that some properties may be measured through other means and therefore have measurement values in addition to the observed values recorded here.
Reference to the superclass object.
Bushing temperature.
Dissolved Gas Analysis. Typical values are: Acceptable, Overheating, Corona, Sparking, Arcing.
Frequency Response Analysis. Typical values are: acceptable, slight movement, significant movement, failed, near failure. A graphic of the response diagram, which is a type of document, may be associated with this analysis through the recursive document relationship of the ProcedureDataSet.
Overall measure of furfural in oil and mechanical strength of paper. DP, the degree of polymerization, is the strength of the paper. Furfural is a measure of furfural compounds, often expressed in parts per million.
Hotspot oil temperature.
Oil Quality Analysis-Color.
Oil Quality Analysis-Dielectric Strength.
Oil Quality Analysis- inter facial tension (IFT) - number-Dynes/CM.
The level of oil in the transformer.
Oil Quality Analysis-Neutralization Number - Number - Mg KOH.
Pump vibration, with typical values being: nominal, high.
undocumented
Top oil temperature.
Water Content expressed in parts per million.
undocumented
undocumented
Transformer star impedance (Pi-model) that accurately reflects impedance for transformers with 2 or 3 windings.
Transformer star impedance (Pi-model) that accurately reflects impedance for transformers with 2 or 3 windings. For transformers with 4 or more windings, you must use TransformerMeshImpedance class.
Reference to the superclass object.
Resistance of the transformer end.
Zero sequence series resistance of the transformer end.
Positive sequence series reactance of the transformer end.
Zero sequence series reactance of the transformer end.
Transformer end datasheet used to calculate this transformer star impedance.
An assembly of two or more coupled windings that transform electrical power between voltage levels.
An assembly of two or more coupled windings that transform electrical power between voltage levels. These windings are bound on a common core and place in the same tank. Transformer tank can be used to model both single-phase and 3-phase transformers.
Reference to the superclass object.
Bank this transformer belongs to.
Transformer tank end represents an individual winding for unbalanced models or for transformer tanks connected into a bank (and bank is modelled with the PowerTransformer).
Transformer tank end represents an individual winding for unbalanced models or for transformer tanks connected into a bank (and bank is modelled with the PowerTransformer).
Reference to the superclass object.
Describes the phases carried by a conducting equipment.
Transformer this winding belongs to.
Set of transformer tank data, from an equipment library.
Set of transformer tank data, from an equipment library.
Reference to the superclass object.
Power transformer data that this tank description is part of.
Test result for transformer ends, such as short-circuit, open-circuit (excitation) or no-load test.
Test result for transformer ends, such as short-circuit, open-circuit (excitation) or no-load test.
Reference to the superclass object.
Base power at which the tests are conducted, usually equal to the rateds of one of the involved transformer ends.
Temperature at which the test is conducted.
This class models the transmission (either a transmission interface or a POR/POD pair) capacity including Total Transfer Capacity (TTC), Operating Transfer Capacity (OTC), and Capacity Benefit Margin (CBM)
This class models the transmission (either a transmission interface or a POR/POD pair) capacity including Total Transfer Capacity (TTC), Operating Transfer Capacity (OTC), and Capacity Benefit Margin (CBM)
Reference to the superclass object.
Capacity Benefit Margin (CBM) is used by Markets to calculate the transmission interface limits. This number could be manually or procedurally determined. The CBM is defined per transmission interface (branch group).
The Operational Transmission Capacity (OTC) is the transmission capacity under the operating condition during a specific time period, incorporating the effects of derates and current settings of operation controls. The OTCs for all transmission interface (branch group) are always provided regardless of outage or switching conditions.
Operating date & hour when the entitlement applies
Total Transmission Capacity
undocumented
undocumented
The Operational Transmission Capacity (OTC) 15 minute Emergency Limit
The Operational Transmission Capacity (OTC) Emergency Limit.
point of delivery
point of receipt
A corridor containing one or more rights of way
A corridor containing one or more rights of way
Reference to the superclass object.
This is formally called the branch group ETC/TOR entitlement with the inclusion of CVR as ETC.
This is formally called the branch group ETC/TOR entitlement with the inclusion of CVR as ETC. Is used to represent the entitlements. This could be also used to represent the TR entitlement on a POR/POD.
Reference to the superclass object.
the entitlement
Operating date and hour when the entitlement applies
undocumented
undocumented
point of delivery
point of receipt
An electrical connection, link, or line consisting of one or more parallel transmission elements between two areas of the interconnected electric systems, or portions thereof.
An electrical connection, link, or line consisting of one or more parallel transmission elements between two areas of the interconnected electric systems, or portions thereof. TransmissionCorridor and TransmissionRightOfWay refer to legal aspects. The TransmissionPath refers to the segments between a TransmissionProvider's ServicePoints.
Reference to the superclass object.
The available transmission capability of a transmission path for the reference direction.
Flag which indicates if the transmission path is also a designated interconnection "parallel path".
The total transmission capability of a transmission path in the reference direction.
A transmission path has a "point-of-delivery" service point
A TransmissionPath is contained in a TransmissionCorridor.
A transmission path has a "point-of-receipt" service point
Provider of the transmission capacity (interconnecting wires between Generation and Consumption) required to fulfill and Energy Transaction's energy exchange.
Provider of the transmission capacity (interconnecting wires between Generation and Consumption) required to fulfill and Energy Transaction's energy exchange. Posts information for transmission paths and AvailableTransmissionCapacities on a reservation node. Buys and sells its products and services on the same reservation node.
Reference to the superclass object.
A transmission reservation is obtained from the OASIS system to reserve transmission for a specified time period, transmission path and transmission product.
A transmission reservation is obtained from the OASIS system to reserve transmission for a specified time period, transmission path and transmission product.
Reference to the superclass object.
undocumented
undocumented
undocumented
undocumented
undocumented
Allows chaining of TransmissionContractRights.
Allows chaining of TransmissionContractRights. Many individual contract rights can be included in the definition of a TransmissionRightChain. A TransmissionRightChain is also defined as a TransmissionContractRight itself.
Reference to the superclass object.
end effective date
start effective date
undocumented
undocumented
A collection of transmission lines that are close proximity to each other.
A collection of transmission lines that are close proximity to each other.
Reference to the superclass object.
A transmission right-of-way is a member of a transmission corridor
A conditions that can trigger remedial actions.
A conditions that can trigger remedial actions.
Reference to the superclass object.
undocumented
undocumented
Turbine Load Controller model developed in the WECC.
Turbine Load Controller model developed in the WECC. This model represents a supervisory turbine load controller that acts to maintain turbine power at a set value by continuous adjustment of the turbine governor speed-load reference. This model is intended to represent slow reset 'outer loop' controllers managing the action of the turbine governor.
Reference to the superclass object.
Controller dead band (db). Typical Value = 0.
Maximum control error (Emax) (note 4). Typical Value = 0.02.
Frequency bias gain (Fb). Typical Value = 0.
Frequency bias flag (Fbf). true = enable frequency bias false = disable frequency bias. Typical Value = false.
Maximum turbine speed/load reference bias (Irmax) (note 3). Typical Value = 0.
Integral gain (Ki). Typical Value = 0.
Proportional gain (Kp). Typical Value = 0.
Base for power values (MWbase) (>0). Unit = MW.
Power controller flag (Pbf). true = enable load controller false = disable load controller. Typical Value = false.
Power controller setpoint (Pmwset) (note 1). Unit = MW. Typical Value = 0.
Type of turbine governor reference (Type). true = speed reference governor false = load reference governor. Typical Value = true.
Power transducer time constant (Tpelec). Typical Value = 0.
Turbine-governor function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Turbine-governor function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Asynchronous machine model with which this turbine-governor model is associated.
Turbine load controller providing input to this turbine-governor.
Turbine-governor function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Turbine-governor function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Turbine load controller function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Turbine load controller function block whose behavior is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Turbine-governor controlled by this turbine load controller.
Turbine load controller function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Turbine load controller function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Catalogue of generic types of assets (TypeAsset) that may be used for design purposes.
Catalogue of generic types of assets (TypeAsset) that may be used for design purposes. It is not associated with a particular manufacturer.
Reference to the superclass object.
undocumented
Documentation for a generic material item that may be used for design, work and other purposes.
Documentation for a generic material item that may be used for design, work and other purposes. Any number of MaterialItems manufactured by various vendors may be used to perform this TypeMaterial.
Reference to the superclass object.
The type of cost to which this Material Item belongs.
The estimated unit cost of this type of material, either for a unit cost or cost per unit length. Cost is for material or asset only and does not include labor to install/construct or configure it.
The value, unit of measure, and multiplier for the quantity.
True if item is a stock item (default).
This model can be derived from UnderexcLimIEEE2.
This model can be derived from UnderexcLimIEEE2. The limit characteristic (look �up table) is a single straight-line, the same as UnderexcLimIEEE2 (see Figure 10.4 (p 32), IEEE 421.5-2005 Section 10.2).
Reference to the superclass object.
Gain Under excitation limiter (Kui). Typical Value = 0.1.
Segment P initial point (P0). Typical Value = 0.
Segment P end point (P1). Typical Value = 1.
Segment Q initial point (Q0). Typical Value = -0.31.
Segment Q end point (Q1). Typical Value = -0.1.
Maximum error signal (VUImax). Typical Value = 1.
Minimum error signal (VUImin). Typical Value = 0.
The class represents the Type UEL1 model which has a circular limit boundary when plotted in terms of machine reactive power vs.
The class represents the Type UEL1 model which has a circular limit boundary when plotted in terms of machine reactive power vs. real power output. Reference: IEEE UEL1 421.5-2005 Section 10.1.
Reference to the superclass object.
UEL center setting (KUC). Typical Value = 1.38.
UEL excitation system stabilizer gain (KUF). Typical Value = 3.3.
UEL integral gain (KUI). Typical Value = 0.
UEL proportional gain (KUL). Typical Value = 100.
UEL radius setting (KUR). Typical Value = 1.95.
UEL lead time constant (TU1). Typical Value = 0.
UEL lag time constant (TU2). Typical Value = 0.05.
UEL lead time constant (TU3). Typical Value = 0.
UEL lag time constant (TU4). Typical Value = 0.
UEL maximum limit for operating point phasor magnitude (VUCMAX). Typical Value = 5.8.
UEL integrator output maximum limit (VUIMAX).
UEL integrator output minimum limit (VUIMIN).
UEL output maximum limit (VULMAX). Typical Value = 18.
UEL output minimum limit (VULMIN). Typical Value = -18.
UEL maximum limit for radius phasor magnitude (VURMAX). Typical Value = 5.8.
The class represents the Type UEL2 which has either a straight-line or multi-segment characteristic when plotted in terms of machine reactive power output vs.
The class represents the Type UEL2 which has either a straight-line or multi-segment characteristic when plotted in terms of machine reactive power output vs. real power output. Reference: IEEE UEL2 421.5-2005 Section 10.2. (Limit characteristic lookup table shown in Figure 10.4 (p 32) of the standard).
Reference to the superclass object.
UEL terminal voltage exponent applied to real power input to UEL limit look-up table (k1). Typical Value = 2.
UEL terminal voltage exponent applied to reactive power output from UEL limit look-up table (k2). Typical Value = 2.
Gain associated with optional integrator feedback input signal to UEL (KFB). Typical Value = 0.
UEL excitation system stabilizer gain (KUF). Typical Value = 0.
UEL integral gain (KUI). Typical Value = 0.5.
UEL proportional gain (KUL). Typical Value = 0.8.
Real power values for endpoints (P0). Typical Value = 0.
Real power values for endpoints (P1). Typical Value = 0.3.
Real power values for endpoints (P10).
Real power values for endpoints (P2). Typical Value = 0.6.
Real power values for endpoints (P3). Typical Value = 0.9.
Real power values for endpoints (P4). Typical Value = 1.02.
Real power values for endpoints (P5).
Real power values for endpoints (P6).
Real power values for endpoints (P7).
Real power values for endpoints (P8).
Real power values for endpoints (P9).
Reactive power values for endpoints (Q0). Typical Value = -0.31.
Reactive power values for endpoints (Q1). Typical Value = -0.31.
Reactive power values for endpoints (Q10).
Reactive power values for endpoints (Q2). Typical Value = -0.28.
Reactive power values for endpoints (Q3). Typical Value = -0.21.
Reactive power values for endpoints (Q4). Typical Value = 0.
Reactive power values for endpoints (Q5).
Reactive power values for endpoints (Q6).
Reactive power values for endpoints (Q7).
Reactive power values for endpoints (Q8).
Reactive power values for endpoints (Q9).
UEL lead time constant (TU1). Typical Value = 0.
UEL lag time constant (TU2). Typical Value = 0.
UEL lead time constant (TU3). Typical Value = 0.
UEL lag time constant (TU4). Typical Value = 0.
Time constant associated with optional integrator feedback input signal to UEL (TUL). Typical Value = 0.
Real power filter time constant (TUP). Typical Value = 5.
Reactive power filter time constant (TUQ). Typical Value = 0.
Voltage filter time constant (TUV). Typical Value = 5.
UEL integrator output maximum limit (VUIMAX). Typical Value = 0.25.
UEL integrator output minimum limit (VUIMIN). Typical Value = 0.
UEL output maximum limit (VULMAX). Typical Value = 0.25.
UEL output minimum limit (VULMIN). Typical Value = 0.
<font color="#0f0f0f">Allis-Chalmers minimum excitation limiter.</font>
<font color="#0f0f0f">Allis-Chalmers minimum excitation limiter.</font>
Reference to the superclass object.
Minimum excitation limit slope (K) (>0).
Differential gain (Kf2).
Minimum excitation limit gain (Km).
Minimum excitation limit value (MELMAX).
Differential time constant (Tf2) (>0).
Minimum excitation limit time constant (Tm).
<font color="#0f0f0f">Westinghouse minimum excitation limiter.</font>
<font color="#0f0f0f">Westinghouse minimum excitation limiter.</font>
Reference to the superclass object.
Differential gain (Kf2).
Minimum excitation limit gain (Km).
Minimum excitation limit value (MELMAX).
Excitation center setting (Qo).
Excitation radius (R).
Differential time constant (Tf2) (>0).
Minimum excitation limit time constant (Tm).
Underexcitation limiter function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Underexcitation limiter function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Excitation system model with which this underexcitation limiter model is associated.
Remote input signal used by this underexcitation limiter model.
Underexcitation limiter function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Underexcitation limiter function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Underground structure.
Underground structure.
Reference to the superclass object.
True if vault is ventilating.
True if vault is ventilating.
Primary material of underground structure.
Date sealing warranty expires.
Resource status at the end of a given clearing period.
Resource status at the end of a given clearing period.
Reference to the superclass object.
Cumulative energy production over trading period.
Cumulative number of status changes of the resource.
Number of start ups in the Operating Day until the end of previous hour.
'true' if the GeneratingUnit is currently On-Line
Resource MW output at the end of previous clearing period.
Resource status at the end of previous clearing period: 0 - off-line 1 - on-line production 2 - in shutdown process 3 - in startup process
Time and date for resourceStatus
Time in market trading intervals the resource is in the state as of the end of the previous clearing period.
Time interval
undocumented
The identification of the unit name for the time series quantities.
The identification of the unit name for the time series quantities.
Reference to the superclass object.
The coded representation of the unit.
undocumented
Unknown element.
Unknown element.
Default parsed element, when no other more specific class applies.
Reference to the superclass object.
Internal contents of the XML element with the unrecognized name.
The line number on which the unknown XML element starts, in Spark this is relative to the split being processed.
The starting character position of the unknown XML element, in Spark this is relative to the split being processed.
The ending character position of the unknown XML element, in Spark this is relative to the split being processed.
The way material and assets are used to perform a certain type of work task.
The way material and assets are used to perform a certain type of work task. The way is described in text in the inheritied description attribute.
Reference to the superclass object.
undocumented
undocumented
Logical or physical point in the network to which readings or events may be attributed.
Logical or physical point in the network to which readings or events may be attributed. Used at the place where a physical or virtual meter may be located; however, it is not required that a meter be present.
Reference to the superclass object.
Tracks the lifecycle of the metering installation at a usage point with respect to readiness for billing via advanced metering infrastructure reads.
True if as a result of an inspection or otherwise, there is a reason to suspect that a previous billing may have been performed with erroneous data. Value should be reset once this potential discrepancy has been resolved.
State of the usage point with respect to connection to the network.
Estimated load.
True if grounded.
If true, this usage point is a service delivery point, i.e., a usage point where the ownership of the service changes hands.
If true, this usage point is virtual, i.e., no physical location exists in the network where a meter could be located to collect the meter readings. For example, one may define a virtual usage point to serve as an aggregation of usage for all of a company's premises distributed widely across the distribution territory. Otherwise, the usage point is physical, i.e., there is a logical point in the network where a meter could be located to collect meter readings.
If true, minimal or zero usage is expected at this usage point for situations such as premises vacancy, logical or physical disconnect. It is used for readings validation and estimation.
Nominal service voltage.
Outage region in which this usage point is located.
Phase code. Number of wires and specific nominal phases can be deduced from enumeration literal values. For example, ABCN is three-phase, four-wire, s12n (splitSecondary12N) is single-phase, three-wire, and s1n and s2n are single-phase, two-wire.
Current flow that this usage point is configured to deliver.
Active power that this usage point is configured to deliver.
Cycle day on which the meter for this usage point will normally be read. Usually correlated with the billing cycle.
Identifier of the route to which this usage point is assigned for purposes of meter reading. Typically used to configure hand held meter reading systems prior to collection of reads.
Remarks about this usage point, for example the reason for it being rated with a non-nominal priority.
Priority of service for this usage point. Note that usage points at the same service location can have different priorities.
Customer agreement regulating this service delivery point.
All equipment connecting this usage point to the electrical grid.
Service category delivered by this usage point.
Service location where the service delivered by this usage point is consumed.
ServiceSupplier (utility) utilising this usage point to deliver a service.
Location of this usage point.
Abstraction for management of group communications within a two-way AMR system or the data for a group of related usage points.
Abstraction for management of group communications within a two-way AMR system or the data for a group of related usage points. Commands can be issued to all of the usage points that belong to a usage point group using a defined group address and the underlying AMR communication infrastructure.
Reference to the superclass object.
Type of this group.
All usage points in this group.
Location of an individual usage point.
Location of an individual usage point.
Reference to the superclass object.
Method for the service person to access this usage point location. For example, a description of where to obtain a key if the facility is unmanned and secured.
Remarks about this location.
Problems previously encountered when visiting or performing work at this location. Examples include: bad dog, violent customer, verbally abusive occupant, obstructions, safety hazards, etc.
Generic name-value pair class, with optional sequence number and units for value; can be used to model parts of information exchange when concrete types are not known in advance.
Generic name-value pair class, with optional sequence number and units for value; can be used to model parts of information exchange when concrete types are not known in advance.
Reference to the superclass object.
Name of an attribute.
Sequence number for this attribute in a list of attributes.
Value of an attribute, including unit information.
undocumented
undocumented
undocumented
Transaction for which this snapshot has been recorded.
The class represents IEEE Voltage Adjuster which is used to represent the voltage adjuster in either a power factor or var control system.
The class represents IEEE Voltage Adjuster which is used to represent the voltage adjuster in either a power factor or var control system. Reference: IEEE Standard 421.5-2005 Section 11.1.
Reference to the superclass object.
Rate at which output of adjuster changes (ADJ_SLEW). Unit = sec./PU. Typical Value = 300.
Time that adjuster pulses are off (TAOFF). Typical Value = 0.5.
Time that adjuster pulses are on (TAON). Typical Value = 0.1.
Set high to provide a continuous raise or lower (VADJF).
Maximum output of the adjuster (VADJMAX). Typical Value = 1.1.
Minimum output of the adjuster (VADJMIN). Typical Value = 0.9.
<font color="#0f0f0f">The class represents the terminal voltage transducer and the load compensator as defined in the IEEE Std 421.5-2005, Section 4.
<font color="#0f0f0f">The class represents the terminal voltage transducer and the load compensator as defined in the IEEE Std 421.5-2005, Section 4. This model is common to all excitation system models described in the IEEE Standard. </font>
Reference to the superclass object.
<font color="#0f0f0f">Resistive component of compensation of a generator (Rc).</font>
<font color="#0f0f0f">Time constant which is used for the combined voltage sensing and compensation signal (Tr).</font>
<font color="#0f0f0f">Reactive component of compensation of a generator (Xc).</font>
<font color="#0f0f0f">The class represents the terminal voltage transducer and the load compensator as defined in the IEEE Std 421.5-2005, Section 4.
<font color="#0f0f0f">The class represents the terminal voltage transducer and the load compensator as defined in the IEEE Std 421.5-2005, Section 4. This model is designed to cover the following types of compensation: </font>
Reference to the superclass object.
<font color="#0f0f0f">Time constant which is used for the combined voltage sensing and compensation signal (Tr).</font>
Describes the translation of a set of values into a name and is intendend to facilitate cusom translations.
Describes the translation of a set of values into a name and is intendend to facilitate cusom translations. Each ValueAliasSet has a name, description etc. A specific Measurement may represent a discrete state like Open, Closed, Intermediate etc. This requires a translation from the MeasurementValue.value number to a string, e.g. 0->"Invalid", 1->"Open", 2->"Closed", 3->"Intermediate". Each ValueToAlias member in ValueAliasSet.Value describe a mapping for one particular value to a name.
Reference to the superclass object.
Describes the translation of one particular value into a name, e.g.
Describes the translation of one particular value into a name, e.g. 1 as "Open".
Reference to the superclass object.
The value that is mapped.
The ValueAliasSet having the ValueToAlias mappings.
Vehicle asset.
Vehicle asset.
Reference to the superclass object.
Date and time the last odometer reading was recorded.
Odometer reading of this vehicle as of the 'odometerReadingDateTime'. Refer to associated ActivityRecords for earlier readings.
Kind of usage of the vehicle.
The entity that owns the point of sale and contracts with the cashier to receipt payments and vend tokens using the payment system.
The entity that owns the point of sale and contracts with the cashier to receipt payments and vend tokens using the payment system. The vendor has a private contract with and is managed by the merchant which is a type of organisation. The vendor is accountable to the merchant for revenue collected, and the merchant is in turn accountable to the supplier.
Reference to the superclass object.
The operating shift for a vendor during which the vendor may transact against the merchant's account.
The operating shift for a vendor during which the vendor may transact against the merchant's account. It aggregates transactions and receipts during the shift and periodically debits a merchant account. The totals in vendor shift should always be the sum of totals aggregated in all cashier shifts that were open under the particular vendor shift.
Reference to the superclass object.
The amount that is to be debited from the merchant account for this vendor shift. This amount reflects the sum(PaymentTransaction.transactionAmount).
If true, merchantDebitAmount has been debited from MerchantAccount; typically happens at the end of VendorShift when it closes.
Merchant account this vendor shift periodically debits (based on aggregated transactions).
Vendor that opens and owns this vendor shift.
A type of limit that indicates if it is enforced and, through association, the organisation responsible for setting the limit.
A type of limit that indicates if it is enforced and, through association, the organisation responsible for setting the limit.
Reference to the superclass object.
True if limit is enforced.
undocumented
undocumented
undocumented
Layers are typically used for grouping diagram objects according to themes and scales.
Layers are typically used for grouping diagram objects according to themes and scales. Themes are used to display or hide certain information (e.g., lakes, borders), while scales are used for hiding or displaying information depending on the current zoom level (hide text when it is too small to be read, or when it exceeds the screen size). This is also called de-cluttering.
Reference to the superclass object.
The drawing order for this layer. The higher the number, the later the layer and the objects within it are rendered.
Voltage adjuster function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Voltage adjuster function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Power Factor or VAr controller Type I model with which this voltage adjuster is associated.
<font color="#0f0f0f">Voltage adjuster</font> function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
<font color="#0f0f0f">Voltage adjuster</font> function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Voltage compensator function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Voltage compensator function block whose behaviour is described by reference to a standard model <font color="#0f0f0f">or by definition of a user-defined model.</font>
Reference to the superclass object.
Excitation system model with which this voltage compensator is associated.
Remote input signal used by this voltage compensator model.
Voltage compensator function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Voltage compensator function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
An area of the power system network which is defined for secondary voltage control purposes.
An area of the power system network which is defined for secondary voltage control purposes. A voltage control zone consists of a collection of substations with a designated bus bar section whose voltage will be controlled.
Reference to the superclass object.
A VoltageControlZone is controlled by a designated BusbarSection.
A VoltageControlZone may have a voltage regulation schedule.
A collection of equipment at one common system voltage forming a switchgear.
A collection of equipment at one common system voltage forming a switchgear. The equipment typically consist of breakers, busbars, instrumentation, control, regulation and protection devices as well as assemblies of all these.
Reference to the superclass object.
The bus bar's high voltage limit
The bus bar's low voltage limit
The base voltage used for all equipment within the voltage level.
The substation of the voltage level.
Operational limit applied to voltage.
Operational limit applied to voltage.
Reference to the superclass object.
Limit on voltage. High or low limit nature of the limit depends upon the properties of the operational limit type.
The P-Q capability curve for a voltage source converter, with P on x-axis and Qmin and Qmax on y1-axis and y2-axis.
The P-Q capability curve for a voltage source converter, with P on x-axis and Qmin and Qmax on y1-axis and y2-axis.
Reference to the superclass object.
DC side of the voltage source converter (VSC).
DC side of the voltage source converter (VSC).
Reference to the superclass object.
Angle between uf and uc. Converter state variable used in power flow.
Droop constant; pu value is obtained as D [kV/MW] x Sb / Ubdc.
Compensation constant. Used to compensate for voltage drop when controlling voltage at a distant bus.
The max quotient between the AC converter voltage (Uc) and DC voltage (Ud). A factor typically less than 1. VSC configuration data used in power flow.
The maximum current through a valve. This current limit is the basis for calculating the capability diagram. VSC configuration data.
Kind of control of real power and/or DC voltage.
undocumented
Reactive power sharing factor among parallel converters on Uac control.
Reactive power injection target in AC grid, at point of common coupling.
Voltage target in AC grid, at point of common coupling.
Line-to-line voltage on the valve side of the converter transformer. Converter state variable, result from power flow.
Capability curve of this converter.
Line traps are devices that impede high frequency power line carrier signals yet present a negligible impedance at the main power frequency.
Line traps are devices that impede high frequency power line carrier signals yet present a negligible impedance at the main power frequency.
Reference to the superclass object.
This represents a source of ambient temperature.
This represents a source of ambient temperature.
Reference to the superclass object.
Counter party in a wheeling transaction.
Counter party in a wheeling transaction.
Reference to the superclass object.
undocumented
A unique identifier of a wheeling transaction.
A unique identifier of a wheeling transaction. A wheeling transaction is a balanced Energy exchange among Supply and Demand Resources.
Reference to the superclass object.
undocumented
The constant aerodynamic torque model assumes that the aerodynamic torque is constant.
The constant aerodynamic torque model assumes that the aerodynamic torque is constant. Reference: IEC Standard 61400-27-1 Section 5.6.1.1.
Reference to the superclass object.
Wind turbine type 1A model with which this wind aerodynamic model is associated.
One-dimensional aerodynamic model.
One-dimensional aerodynamic model. Reference: IEC Standard 614000-27-1 Section 5.6.1.2.
Reference to the superclass object.
Aerodynamic gain (ka). It is type dependent parameter.
Initial pitch angle (thetaomega0). It is case dependent parameter.
Wind turbine type 3 model with which this wind aerodynamic model is associated.
Two-dimensional aerodynamic model.
Two-dimensional aerodynamic model. Reference: IEC Standard 614000-27-1 Section 5.6.1.3.
Reference to the superclass object.
Partial derivative of aerodynamic power with respect to changes in WTR speed (dpomega). It is type dependent parameter.
Partial derivative of aerodynamic power with respect to changes in pitch angle (dptheta). It is type dependent parameter.
Partial derivative (dpv1). It is type dependent parameter.
Rotor speed if the wind turbine is not derated (omega0). It is type dependent parameter.
Available aerodynamic power (pavail). It is case dependent parameter.
Blade angle at twice rated wind speed (thetav2). It is type dependent parameter.
Pitch angle if the wind turbine is not derated (theta0). It is case dependent parameter.
Wind turbine type 3 model with which this wind aerodynamic model is associated.
Current limitation model.
Current limitation model. The current limitation model combines the physical limits and the control limits.
Reference to the superclass object.
Maximum continuous current at the wind turbine terminals (imax). It is type dependent parameter.
Maximum current during voltage dip at the wind turbine terminals (imaxdip). It is project dependent parameter.
Partial derivative of reactive current limit (Kpqu). It is type dependent parameter.
Limitation of type 3 stator current (MDFSLim):
Prioritisation of q control during UVRT (Mqpri):
Voltage measurement filter time constant (Tufiltcl). It is type dependent parameter.
Wind turbine voltage in the operation point where zero reactive current can be delivered (upqumax). It is type dependent parameter.
Wind turbine type 3 or 4 model with which this wind control current limitation model is associated.
P control model Type 3.
P control model Type 3. Reference: IEC Standard 61400-27-1 Section 5.6.5.4.
Reference to the superclass object.
Maximum wind turbine power ramp rate (dpmax). It is type dependent parameter.
Maximum ramp rate of wind turbine reference power (dprefmax). It is project dependent parameter.
Minimum ramp rate of wind turbine reference power (dprefmin). It is project dependent parameter.
Ramp limitation of torque, required in some grid codes (dtmax). It is project dependent parameter.
Limitation of torque rise rate during UVRT (dthetamaxUVRT). It is project dependent parameter.
Gain for active drive train damping (KDTD). It is type dependent parameter.
PI controller integration parameter (KIp). It is type dependent parameter.
PI controller proportional gain (KPp). It is type dependent parameter.
Enable UVRT power control mode (MpUVRT). true = 1: voltage control false = 0: reactive power control. It is project dependent parameter.
Offset to reference value that limits controller action during rotor speed changes (omegaoffset). It is case dependent parameter.
Maximum active drive train damping power (pDTDmax). It is type dependent parameter.
Time delay after deep voltage sags (TDVS). It is project dependent parameter.
Minimum electrical generator torque (temin). It is type dependent parameter.
Voltage scaling factor of reset-torque (tuscale). It is project dependent parameter.
Filter time constant for generator speed measurement (Tomegafiltp3). It is type dependent parameter.
Filter time constant for power measurement (Tpfiltp3). It is type dependent parameter.
Time constant in power order lag (Tpord). It is type dependent parameter.
Filter time constant for voltage measurement (Tufiltp3). It is type dependent parameter.
Time constant in speed reference filter (Tomega,ref). It is type dependent parameter.
Voltage limit for hold UVRT status after deep voltage sags (uDVS). It is project dependent parameter.
Voltage dip threshold for P-control (uPdip). Part of turbine control, often different (e.g 0.8) from converter thresholds. It is project dependent parameter.
Active drive train damping frequency (omegaDTD). It can be calculated from two mass model parameters. It is type dependent parameter.
Coefficient for active drive train damping (zeta). It is type dependent parameter.
Wind turbine type 3 model with which this Wind control P type 3 model is associated.
P control model Type 4A.
P control model Type 4A. Reference: IEC Standard 61400-27-1 Section 5.6.5.5.
Reference to the superclass object.
Maximum wind turbine power ramp rate (dpmaxp4A). It is project dependent parameter.
Time constant in power order lag (Tpordp4A). It is type dependent parameter.
Voltage measurement filter time constant (Tufiltp4A). It is type dependent parameter.
Wind turbine type 4A model with which this wind control P type 4A model is associated.
P control model Type 4B.
P control model Type 4B. Reference: IEC Standard 61400-27-1 Section 5.6.5.6.
Reference to the superclass object.
Maximum wind turbine power ramp rate (dpmaxp4B). It is project dependent parameter.
Time constant in aerodynamic power response (Tpaero). It is type dependent parameter.
Time constant in power order lag (Tpordp4B). It is type dependent parameter.
Voltage measurement filter time constant (Tufiltp4B). It is type dependent parameter.
Wind turbine type 4B model with which this wind control P type 4B model is associated.
Pitch angle control model.
Pitch angle control model. Reference: IEC Standard 61400-27-1 Section 5.6.5.2.
Reference to the superclass object.
Maximum pitch positive ramp rate (dthetamax). It is type dependent parameter. Unit = degrees/sec.
Maximum pitch negative ramp rate (dthetamin). It is type dependent parameter. Unit = degrees/sec.
Power PI controller integration gain (KIc). It is type dependent parameter.
Speed PI controller integration gain (KIomega). It is type dependent parameter.
Power PI controller proportional gain (KPc). It is type dependent parameter.
Speed PI controller proportional gain (KPomega). It is type dependent parameter.
Pitch cross coupling gain (KPX). It is type dependent parameter.
Maximum pitch angle (thetamax). It is type dependent parameter.
Minimum pitch angle (thetamin). It is type dependent parameter.
Pitch time constant (ttheta). It is type dependent parameter.
Wind turbine type 3 model with which this pitch control model is associated.
Q control model.
Q control model. Reference: IEC Standard 61400-27-1 Section 5.6.5.7.
Reference to the superclass object.
Maximum reactive current injection during dip (iqh1). It is type dependent parameter.
Maximum reactive current injection (iqmax). It is type dependent parameter.
Minimum reactive current injection (iqmin). It is type dependent parameter.
Post fault reactive current injection (iqpost). It is project dependent parameter.
Reactive power PI controller integration gain (KI,q). It is type dependent parameter.
Voltage PI controller integration gain (KI,u). It is type dependent parameter.
Reactive power PI controller proportional gain (KP,q). It is type dependent parameter.
Voltage PI controller proportional gain (KP,u). It is type dependent parameter.
Voltage scaling factor for UVRT current (Kqv). It is project dependent parameter.
Resistive component of voltage drop impedance (rdroop). It is project dependent parameter.
Power measurement filter time constant (Tpfiltq). It is type dependent parameter.
Length of time period where post fault reactive power is injected (Tpost). It is project dependent parameter.
Time constant in reactive power order lag (Tqord). It is type dependent parameter.
Voltage measurement filter time constant (Tufiltq). It is type dependent parameter.
Voltage dead band lower limit (udb1). It is type dependent parameter.
Voltage dead band upper limit (udb2). It is type dependent parameter.
Maximum voltage in voltage PI controller integral term (umax). It is type dependent parameter.
Minimum voltage in voltage PI controller integral term (umin). It is type dependent parameter.
Voltage threshold for UVRT detection in q control (uqdip). It is type dependent parameter.
User defined bias in voltage reference (uref0), used when MqG is set to voltage control. It is case dependent parameter.
Types of general wind turbine Q control modes (MqG). It is project dependent parameter.
Types of UVRT Q control modes (MqUVRT). It is project dependent parameter.
Inductive component of voltage drop impedance (xdroop). It is project dependent parameter.
Wind turbine type 3 or 4 model with which this reactive control model is associated.
Constant Q limitation model.
Constant Q limitation model. Reference: IEC Standard 61400-27-1 Section 5.6.5.9.
Reference to the superclass object.
Maximum reactive power (qmax). It is type dependent parameter.
Minimum reactive power (qmin). It is type dependent parameter.
Wind generator type 3 or 4 model with which this constant Q limitation model is associated.
QP and QU limitation model.
QP and QU limitation model. Reference: IEC Standard 61400-27-1 Section 5.6.5.10.
Reference to the superclass object.
Power measurement filter time constant for Q capacity (Tpfiltql). It is type dependent parameter.
Voltage measurement filter time constant for Q capacity (Tufiltql). It is type dependent parameter.
Wind generator type 3 or 4 model with which this QP and QU limitation model is associated.
Rotor resistance control model.
Rotor resistance control model. Reference: IEC Standard 61400-27-1 Section 5.6.5.3.
Reference to the superclass object.
Integral gain in rotor resistance PI controller (KIrr). It is type dependent parameter.
Filter gain for generator speed measurement (Komegafilt). It is type dependent parameter.
Filter gain for power measurement (Kpfilt). It is type dependent parameter.
Proportional gain in rotor resistance PI controller (KPrr). It is type dependent parameter.
Maximum rotor resistance (rmax). It is type dependent parameter.
Minimum rotor resistance (rmin). It is type dependent parameter.
Filter time constant for generator speed measurement (Tomegafiltrr). It is type dependent parameter.
Filter time constant for power measurement (Tpfiltrr). It is type dependent parameter.
Wind turbine type 2 model with whitch this wind control rotor resistance model is associated.
The class models a look up table for the purpose of wind standard models.
The class models a look up table for the purpose of wind standard models.
Reference to the superclass object.
Input value (x) for the lookup table function.
Type of the lookup table function.
Output value (y) for the lookup table function.
Sequence numbers of the pairs of the input (x) and the output (y) of the lookup table function.
The current control limitation model with which this wind dynamics lookup table is associated.
The P control type 3 model with which this wind dynamics lookup table is associated.
The QP and QU limitation model with which this wind dynamics lookup table is associated.
The rotor resistance control model with which this wind dynamics lookup table is associated.
The generator type 3B model with which this wind dynamics lookup table is associated.
The pitch control power model with which this wind dynamics lookup table is associated.
The frequency and active power wind plant control model with which this wind dynamics lookup table is associated.
The voltage and reactive power wind plant control model with which this wind dynamics lookup table is associated.
The grid protection model with which this wind dynamics lookup table is associated.
Wind turbine IEC Type 1A.
Wind turbine IEC Type 1A. Reference: IEC Standard 61400-27-1, section 5.5.2.2.
Reference to the superclass object.
Wind aerodynamic model associated with this wind turbine type 1A model.
Wind turbine IEC Type 1B.
Wind turbine IEC Type 1B. Reference: IEC Standard 61400-27-1, section 5.5.2.3.
Reference to the superclass object.
Pitch control power model associated with this wind turbine type 1B model.
Wind turbine IEC Type 2.
Wind turbine IEC Type 2. Reference: IEC Standard 61400-27-1, section 5.5.3.
Reference to the superclass object.
Wind control rotor resistance model associated with wind turbine type 2 model.
Pitch control power model associated with this wind turbine type 2 model.
Parent class supporting relationships to IEC wind turbines Type 3 generator models of IEC type 3A and 3B.
Parent class supporting relationships to IEC wind turbines Type 3 generator models of IEC type 3A and 3B.
Reference to the superclass object.
Maximum active current ramp rate (dipmax). It is project dependent parameter.
Maximum reactive current ramp rate (diqmax). It is project dependent parameter.
Electromagnetic transient reactance (xS). It is type dependent parameter.
Wind turbine type 3 model with which this wind generator type 3 is associated.
IEC Type 3A generator set model.
IEC Type 3A generator set model. Reference: IEC Standard 61400-27-1 Section 5.6.3.2.
Reference to the superclass object.
Current PI controller proportional gain (KPc). It is type dependent parameter.
Current PI controller integration time constant (TIc). It is type dependent parameter.
Wind turbine type 4 model with which this wind generator type 3A model is associated.
IEC Type 3B generator set model.
IEC Type 3B generator set model. Reference: IEC Standard 61400-27-1 Section 5.6.3.3.
Reference to the superclass object.
Crowbar control mode (MWTcwp).
Current generation Time constant (Tg). It is type dependent parameter.
Time constant for crowbar washout filter (Two). It is case dependent parameter.
IEC Type 4 generator set model.
IEC Type 4 generator set model. Reference: IEC Standard 61400-27-1 Section 5.6.3.4.
Reference to the superclass object.
Maximum active current ramp rate (dipmax). It is project dependent parameter.
Maximum reactive current ramp rate (diqmax). It is project dependent parameter.
Minimum reactive current ramp rate (diqmin). It is case dependent parameter.
Time constant (Tg). It is type dependent parameter.
Wind turbine type 4A model with which this wind generator type 4 model is associated.
Wind turbine type 4B model with which this wind generator type 4 model is associated.
A wind driven generating unit.
A wind driven generating unit. May be used to represent a single turbine or an aggregation.
Reference to the superclass object.
The kind of wind generating unit
Two mass model.
Two mass model. Reference: IEC Standard 61400-27-1 Section 5.6.2.1.
Reference to the superclass object.
Drive train damping (cdrt). It is type dependent parameter.
Inertia constant of generator (Hgen). It is type dependent parameter.
Inertia constant of wind turbine rotor (HWTR). It is type dependent parameter.
Drive train stiffness (kdrt). It is type dependent parameter.
Wind generator type 1 or 2 model with which this wind mechanical model is associated.
Wind turbine Type 3 model with which this wind mechanical model is associated.
Wind turbine type 4B model with which this wind mechanical model is associated.
Pitch control power model.
Pitch control power model. Reference: IEC Standard 61400-27-1 Section 5.6.5.1.
Reference to the superclass object.
Rate limit for increasing power (dpmax). It is type dependent parameter.
Rate limit for decreasing power (dpmin). It is type dependent parameter.
Minimum power setting (pmin). It is type dependent parameter.
If pinit < pset then power will ne ramped down to pmin. It is (pset) in the IEC 61400-27-1. It is type dependent parameter.
Lag time constant (T1). It is type dependent parameter.
Voltage measurement time constant (Tr). It is type dependent parameter.
Dip detection threshold (uUVRT). It is type dependent parameter.
Wind turbine type 1B model with which this Pitch control power model is associated.
Wind turbine type 2 model with which this Pitch control power model is associated.
Parent class supporting relationships to wind turbines Type 3 and 4 and wind plant IEC and user defined wind plants including their control models.
Parent class supporting relationships to wind turbines Type 3 and 4 and wind plant IEC and user defined wind plants including their control models.
Reference to the superclass object.
The remote signal with which this power plant is associated.
Frequency and active power controller model.
Frequency and active power controller model. Reference: IEC Standard 61400-27-1 Annex D.
Reference to the superclass object.
Maximum ramp rate of pWTref request from the plant controller to the wind turbines (dprefmax). It is case dependent parameter.
Minimum (negative) ramp rate of pWTref request from the plant controller to the wind turbines (dprefmin). It is project dependent parameter.
Maximum positive ramp rate for wind plant power reference (dpWPrefmax). It is project dependent parameter.
Maximum negative ramp rate for wind plant power reference (dpWPrefmin). It is project dependent parameter.
Plant P controller integral gain (KIWPp). It is project dependent parameter.
Maximum PI integrator term (KIWPpmax). It is project dependent parameter.
Minimum PI integrator term (KIWPpmin). It is project dependent parameter.
Plant P controller proportional gain (KPWPp). It is project dependent parameter.
Power reference gain (KWPpref). It is project dependent parameter.
Maximum pWTref request from the plant controller to the wind turbines (prefmax). It is project dependent parameter.
Minimum pWTref request from the plant controller to the wind turbines (prefmin). It is project dependent parameter.
Lead time constant in reference value transfer function (Tpft). It is project dependent parameter.
Lag time constant in reference value transfer function (Tpfv). It is project dependent parameter.
Filter time constant for frequency measurement (TWPffiltp). It is project dependent parameter.
Filter time constant for active power measurement (TWPpfiltp). It is project dependent parameter.
Wind plant model with which this wind plant frequency and active power control is associated.
Simplified IEC type plant level model.
Simplified IEC type plant level model. Reference: IEC 61400-27-1, Annex D.
Reference to the superclass object.
Wind plant frequency and active power control model associated with this wind plant.
Wind plant model with which this wind reactive control is associated.
Simplified plant voltage and reactive power control model for use with type 3 and type 4 wind turbine models.
Simplified plant voltage and reactive power control model for use with type 3 and type 4 wind turbine models. Reference: IEC Standard 61400-27-1 Annex D.
Reference to the superclass object.
Maximum positive ramp rate for wind turbine reactive power/voltage reference (dxrefmax). It is project dependent parameter.
Maximum negative ramp rate for wind turbine reactive power/voltage reference (dxrefmin). It is project dependent parameter.
Plant Q controller integral gain (KIWPx). It is project dependent parameter.
Maximum reactive Power/voltage reference from integration (KIWPxmax). It is project dependent parameter.
Minimum reactive Power/voltage reference from integration (KIWPxmin). It is project dependent parameter.
Plant Q controller proportional gain (KPWPx). It is project dependent parameter.
Reactive power reference gain (KWPqref). It is project dependent parameter.
Plant voltage control droop (KWPqu). It is project dependent parameter.
Filter time constant for voltage dependent reactive power (Tuqfilt). It is project dependent parameter.
Filter time constant for active power measurement (TWPpfiltq). It is project dependent parameter.
Filter time constant for reactive power measurement (TWPqfiltq). It is project dependent parameter.
Filter time constant for voltage measurement (TWPufiltq). It is project dependent parameter.
Lead time constant in reference value transfer function (Txft). It is project dependent parameter.
Lag time constant in reference value transfer function (Txfv). It is project dependent parameter.
Voltage threshold for UVRT detection in q control (uWPqdip). It is project dependent parameter.
Reactive power/voltage controller mode (MWPqmode). It is case dependent parameter.
Maximum xWTref (qWTref or delta uWTref) request from the plant controller (xrefmax). It is case dependent parameter.
Minimum xWTref (qWTref or deltauWTref) request from the plant controller (xrefmin). It is project dependent parameter.
Wind plant reactive control model associated with this wind plant.
Wind plant function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Wind plant function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
The grid protection model includes protection against over and under voltage, and against over and under frequency.
The grid protection model includes protection against over and under voltage, and against over and under frequency. Reference: IEC Standard 614000-27-1 Section 5.6.6.
Reference to the superclass object.
Maximum rate of change of frequency (dFmax). It is type dependent parameter.
Wind turbine over frequency protection activation threshold (fover). It is project dependent parameter.
Wind turbine under frequency protection activation threshold (funder). It is project dependent parameter.
Zero crossing measurement mode (Mzc). True = 1 if the WT protection system uses zero crossings to detect frequency � otherwise false = 0. It is type dependent parameter.
Time interval of moving average window (TfMA). It is type dependent parameter.
Wind turbine over voltage protection activation threshold (uover). It is project dependent parameter.
Wind turbine under voltage protection activation threshold (uunder). It is project dependent parameter.
Wind generator type 1 or 2 model with which this wind turbine protection model is associated.
Wind generator type 3 or 4 model with which this wind turbine protection model is associated.
Reference frame rotation model.
Reference frame rotation model. Reference: IEC Standard 61400-27-1 Section 5.6.3.5.
Reference to the superclass object.
Time constant for PLL first order filter model (TPLL). It is type dependent parameter.
Voltage below which the angle of the voltage is filtered and possibly also frozen (uPLL1). It is type dependent parameter.
Voltage (uPLL2) below which the angle of the voltage is frozen if uPLL2 is smaller or equal to uPLL1 . It is type dependent parameter.
Wind turbine type 3 or 4 model with which this reference frame rotation model is associated.
Parent class supporting relationships to wind turbines Type 1 and 2 and their control models.
Parent class supporting relationships to wind turbines Type 1 and 2 and their control models.
Reference to the superclass object.
Asynchronous machine model with which this wind generator type 1 or 2 model is associated.
Remote input signal used by this wind generator Type 1 or Type 2 model.
Parent class supporting relationships to IEC wind turbines Type 1 and 2 including their control models.
Parent class supporting relationships to IEC wind turbines Type 1 and 2 including their control models. Generator model for wind turbine of IEC Type 1 or Type 2 is a standard asynchronous generator model.
Reference to the superclass object.
Wind mechanical model associated with this wind generator type 1 or 2 model.
Wind turbune protection model associated with this wind generator type 1 or 2 model.
Parent class supporting relationships to IEC wind turbines Type 3 including their control models.
Parent class supporting relationships to IEC wind turbines Type 3 including their control models.
Reference to the superclass object.
Wind aerodynamic model associated with this wind generator type 3 model.
Wind aerodynamic model associated with this wind turbine type 3 model.
Wind control P type 3 model associated with this wind turbine type 3 model.
Wind control pitch angle model associated with this wind turbine type 3.
Wind generator Type 3 model associated with this wind turbine type 3 model.
Wind mechanical model associated with this wind turbine Type 3 model.
Parent class supporting relationships to wind turbines Type 3 and 4 and wind plant including their control models.
Parent class supporting relationships to wind turbines Type 3 and 4 and wind plant including their control models.
Reference to the superclass object.
Energy Source (current source) with which this wind Type 3 or 4 dynamics model is asoociated.
Remote input signal used by these wind turbine Type 3 or 4 models.
The wind plant with which the wind turbines type 3 or 4 are associated.
Parent class supporting relationships to IEC wind turbines Type 3 and 4 including their control models.
Parent class supporting relationships to IEC wind turbines Type 3 and 4 including their control models.
Reference to the superclass object.
Wind control Q model associated with this wind turbine type 3 or 4 model.
Wind control current limitation model associated with this wind turbine type 3 or 4 model.
Constant Q limitation model associated with this wind generator type 3 or 4 model.
QP and QU limitation model associated with this wind generator type 3 or 4 model.
Wind turbune protection model associated with this wind generator type 3 or 4 model.
Reference frame rotation model associated with this wind turbine type 3 or 4 model.
Parent class supporting relationships to IEC wind turbines Type 4 including their control models.
Parent class supporting relationships to IEC wind turbines Type 4 including their control models.
Reference to the superclass object.
Wind generator type 3A model associated with this wind turbine type 4 model.
Wind turbine IEC Type 4A.
Wind turbine IEC Type 4A. Reference: IEC Standard 61400-27-1, section 5.5.5.3.
Reference to the superclass object.
Wind control P type 4A model associated with this wind turbine type 4A model.
Wind generator type 4 model associated with this wind turbine type 4A model.
Wind turbine IEC Type 4A.
Wind turbine IEC Type 4A. Reference: IEC Standard 61400-27-1, section 5.5.5.2.
Reference to the superclass object.
Wind control P type 4B model associated with this wind turbine type 4B model.
Wind generator type 4 model associated with this wind turbine type 4B model.
Wind mechanical model associated with this wind turbine Type 4B model.
Wind Type 1 or Type 2 function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Wind Type 1 or Type 2 function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Wind Type 3 or Type 4 function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Wind Type 3 or Type 4 function block whose dynamic behaviour is described by <font color="#0f0f0f">a user-defined model.</font>
Reference to the superclass object.
Behaviour is based on proprietary model as opposed to detailed model. true = user-defined model is proprietary with behaviour mutually understood by sending and receiving applications and parameters passed as general attributes false = user-defined model is explicitly defined in terms of control blocks and their input and output signals.
Winding insulation condition as a result of a test.
Winding insulation condition as a result of a test.
Reference to the superclass object.
Status of Winding Insulation Power Factor as of statusDate: Acceptable, Minor Deterioration or Moisture Absorption, Major Deterioration or Moisture Absorption, Failed.
For testType, status of Winding Insulation Resistance as of statusDate. Typical values are: Acceptable, Questionable, Failed.
As of statusDate, the leakage reactance measured at the "from" winding with the "to" winding short-circuited and all other windings open-circuited.
undocumented
undocumented
undocumented
undocumented
Wire data that can be specified per line segment phase, or for the line segment as a whole in case its phases all have the same wire characteristics.
Wire data that can be specified per line segment phase, or for the line segment as a whole in case its phases all have the same wire characteristics.
Reference to the superclass object.
(if there is a different core material) Radius of the central core.
(if used) Number of strands in the steel core.
Geometric mean radius. If we replace the conductor by a thin walled tube of radius GMR, then its reactance is identical to the reactance of the actual conductor.
True if conductor is insulated.
(if insulated conductor) Material used for insulation.
(if insulated conductor) Thickness of the insulation.
Conductor material.
AC resistance per unit length of the conductor at 25 �C.
AC resistance per unit length of the conductor at 50 �C.
AC resistance per unit length of the conductor at 75 �C.
DC resistance per unit length of the conductor at 20 �C.
Outside radius of the wire.
Current carrying capacity of the wire under stated thermal conditions.
Describes the wire gauge or cross section (e.g., 4/0, #2, 336.5).
Number of strands in the conductor.
All per-length parameters calculated from this wire datasheet.
Identification, spacing and configuration of the wires of a conductor with respect to a structure.
Identification, spacing and configuration of the wires of a conductor with respect to a structure.
Reference to the superclass object.
Single phase or neutral designation for the wire with this position.
Signed horizontal distance from the wire at this position to a common reference point.
Signed vertical distance from the wire at this position: above ground (positive value) or burial depth below ground (negative value).
Wire spacing data this wire position belongs to.
Wire spacing data that associates multiple wire positions with the line segment, and allows to calculate line segment impedances.
Wire spacing data that associates multiple wire positions with the line segment, and allows to calculate line segment impedances. Number of phases can be derived from the number of associated wire positions whose phase is not neutral.
Reference to the superclass object.
If true, this spacing data describes a cable.
Number of wire sub-conductors in the symmetrical bundle (typically between 1 and 4).
Distance between wire sub-conductors in a symmetrical bundle.
Usage of the associated wires.
undocumented
undocumented
Document used to request, initiate, track and record work.
Document used to request, initiate, track and record work.
Reference to the superclass object.
Date and time work was requested.
undocumented
undocumented
undocumented
undocumented
Asset used to perform work.
Asset used to perform work.
Reference to the superclass object.
Crew using this work asset.
Billing information for work performed for the customer.
Billing information for work performed for the customer. The history of Work Billing Info, Invoices, and Payments is to be maintained in associated ActivityRecords.
Reference to the superclass object.
Estimated cost for work.
Amount of price on deposit.
Discount from standard price.
Date and time by which payment for bill is expected from client.
Date and time bill was issued to client.
Date payment was received from client.
Amount of bill.
undocumented
undocumented
A collection of all of the individual cost items collected from multiple sources.
A collection of all of the individual cost items collected from multiple sources.
Reference to the superclass object.
Amount in designated currency for work, either a total or an individual element. As defined in the attribute "type," multiple instances are applicable to each work for: planned cost, actual cost, authorized cost, budgeted cost, forecasted cost, other.
True if 'amount' is a debit, false if it is a credit.
Date and time that 'amount' is posted to the work.
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
undocumented
A roll up by cost type for the entire cost of a work order.
A roll up by cost type for the entire cost of a work order. For example, total labor.
Reference to the superclass object.
undocumented
Shadow class for Document, to isolate subclassing from this package.
Shadow class for Document, to isolate subclassing from this package. If any subclass gets normative and needs inheritance, it will inherit directly from Document.
Reference to the superclass object.
A pre-defined set of work steps for a given type of work.
A pre-defined set of work steps for a given type of work.
Reference to the superclass object.
Used to define dependencies of each work flow step, which is for the instance of WorkTask associated with a given instance of WorkFlow.
undocumented
undocumented
Shadow class for IdentifiedObject, to isolate subclassing from this package.
Shadow class for IdentifiedObject, to isolate subclassing from this package. If any subclass gets normative and needs inheritance, it will inherit directly from IdentifiedObject.
Reference to the superclass object.
Information about a particular location for various forms of work.
Information about a particular location for various forms of work.
Reference to the superclass object.
undocumented
A type of ActivityRecord that records information about the status of an item, such as a Work or WorkTask, at a point in time.
A type of ActivityRecord that records information about the status of an item, such as a Work or WorkTask, at a point in time.
Reference to the superclass object.
Estimated percentage of completion of this individual work task or overall work order.
Time schedule specific to work.
Time schedule specific to work.
Reference to the superclass object.
Kind of this work schedule.
Time schedule for this work or work task.
Area divided off from other areas.
Area divided off from other areas. It may be part of the electrical network, a land area where special restrictions apply, weather areas, etc. For weather, it is an area where a set of relatively homogenous weather measurements apply.
Reference to the superclass object.
Kind of this zone.
A unit with valves for three phases, together with unit control equipment, essential protective and switching devices, DC storage capacitors, phase reactors and auxiliaries, if any, used for conversion.
Reference to the superclass object.
Base apparent power of the converter pole.
Converter DC current, also called Id. Converter state variable, result from power flow.
Active power loss in pole at no power transfer. Converter configuration data used in power flow.
The maximum voltage on the DC side at which the converter should operate. Converter configuration data used in power flow.
Min allowed converter DC voltage. Converter configuration data used in power flow.
Number of valves in the converter. Used in loss calculations.
Active power at the point of common coupling. Load sign convention is used, i.e. positive sign means flow out from a node.
The active power loss at a DC Pole = idleLoss + switchingLoss*|Idc| + resitiveLoss*Idc2 For lossless operation Pdc=Pac For rectifier operation with losses Pdc=Pac-lossP For inverter operation with losses Pdc=Pac+lossP Converter state variable used in power flow.
Reactive power at the point of common coupling. Load sign convention is used, i.e. positive sign means flow out from a node.
Rated converter DC voltage, also called UdN. Converter configuration data used in power flow.
Converter configuration data used in power flow. Refer to poleLossP.
Switching losses, relative to the base apparent power 'baseS'. Refer to poleLossP.
Real power injection target in AC grid, at point of common coupling.
Target value for DC voltage magnitude.
Line-to-line converter voltage, the voltage at the AC side of the valve. Converter state variable, result from power flow.
Converter voltage at the DC side, also called Ud. Converter state variable, result from power flow.
Valve threshold voltage, also called Uvalve. Forward voltage drop when the valve is conducting. Used in loss calculations, i.e. the switchLoss depends on numberOfValves * valveU0.
Point of common coupling terminal for this converter DC side. It is typically the terminal on the power transformer (or switch) closest to the AC network. The power flow measurement must be the sum of all flows into the transformer.